Extech Instruments FM200 User manual

User Manual
Formaldehyde Thermo-Hygrometer
Model FM200
Additional User Manual Translations available at www.extech.com
www. .com [e-mail]1.800.561.8187

EXTECH INSTRUMENTS
2FM200-en-GB_V1.8 3/17
Introduction
Thank you for selecting the Extech Instruments Model FM200. The FM200 measures
Formaldehyde CH2O (HCHO) concentration, Air Temperature, and Relative Humidity. The alarm
feature alerts the user when the Formaldehyde 0.08ppm limit is exceeded.
This device is shipped fully tested and calibrated and, with proper use, will provide years of
reliable service. Please visit our website (www.extech.com) to check for the latest version of this
User Guide, Product Updates,
Features
•Measures Formaldehyde, Temperature, and Relative Humidity
•Built-in fan to quickly intake gas via pliable tube
•Pliable tube available for restricting samples
•Triple line, large LCD display
•Display Backlight function for working in dimly lit areas
•Automatic temperature compensation
•Hold function freezes current readings
•Store and recall maximum and minimum readings
•Self-calibration feature
•Auto power off after 15 minutes of inactivity conserves battery energy
•HCHO high alarm threshold setting with audible beeper
•Electrochemical sensor, capable of measuring up to 5ppm of HCHO
•Tripod mount on sensor and meter
www. .com [e-mail]1.800.561.8187

EXTECH INSTRUMENTS
3FM200-en-GB_V1.8 3/17
Meter Description
1. LCD Display
2. HOLD/ Up Arrow Button
3. MODE/ Left Arrow Button
4. SET Button
5. AC adaptor jack
6. Tripod mount (detachable probe also has a
Tripod mount)
7. Probe connection
8. (Power) Button
9. MAX-MIN/ Right arrow
10. UNIT Button
11. Down Arrow / Backlight Button
12. Inlet/Outlet ports for tubing
13. Detachable Probe
14. Probe LED indicators
Note: Battery compartment located on back of the meter. A tripod mounting port is available on
the back of the external probe.
www. .com [e-mail]1.800.561.8187

EXTECH INSTRUMENTS
4FM200-en-GB_V1.8 3/17
Operation
External Probe and Status LED indicators
Attach the External Probe to the connector at the top of the meter. The status indicators on the
Probe will flash red when the Sampling Fan is on, solid red when the Sampling Fan is off, and
green when the Probe is connected to the meter and functioning normally. The user can connect
the supplied tubing to the External Probe’s INLET/OUTLET ports. A Tripod Mount is located on
the back of the External Probe (in addition to the one at the bottom of the meter).
Powering on the meter
Short press the button to power on the meter. Alternatively, use the AC/DC adaptor to power
the meter. When powered on, the meter LCD shows “0000” for a period of time (depending on
the period of time the meter has been inactive). The meter then counts from “9999” down to
“0000”.
Once the meter reaches “0000”, the HCHO level will be shown along with the
Temperature/Humidity readings (Temperature and RH% displays alternate every 3 seconds).
Note: For short term measurements, battery power can be used. For datalogging or long term
usage, use the AC/DC adaptor to conserve battery energy.
Auto Power Off & Disable
The meter will automatically turn off after 15 minutes of inactivity. To disable the auto power off
function: with meter OFF, press and hold the HOLD button first, followed by the button. The
LCD will show “n”, and will then return to normal measurement mode.
Turning the Sampling Fan ON/OFF
Press the SET button to toggle the air sampling fan ON and OFF. When the fan is ON its motion
will generate an audible sound and a vibration.
MAX-MIN Memory
Short press the MAX/MIN button to scroll through Maximum value, Minimum value, and then
back to the normal operating mode. Press and hold the HOLD button to clear the maximum or
minimum memory values (depending on which mode is displaying) and then return to the
normal operating mode as just described. The meter will then begin recording new maximum
and minimum readings.
www. .com [e-mail]1.800.561.8187

EXTECH INSTRUMENTS
5FM200-en-GB_V1.8 3/17
Changing Temperature Units oC/oF
Short press the UNIT button (while the temperature is being displayed) to switch between °C
and °F units.
High Alarm with Beeper
The alarm threshold range is 0.00 to 5.00ppm. The meter defaults to a 0.08ppm HCHO alarm
threshold. To enter the alarm threshold setting mode, press and hold the SET button. Press the
HOLD / button to increase the value or press the / button to decrease the value. Press
the MODE/ button to select the digit to the left and press the / button to select the digit
to the right. Press and hold the SET button to save the changes. The LCD display will show
“SAVE” and return to its normal mode of operation.
Note: A bell icon is shown on the top left corner of the LCD display when the alarm is
armed. Short press the POWER button to arm or disarm the alarm.
www. .com [e-mail]1.800.561.8187

EXTECH INSTRUMENTS
6FM200-en-GB_V1.8 3/17
Hold Function
Press the HOLD button to freeze the current readings on the screen during normal measurement
mode. The HOLD icon will display when HOLD is activated. In the HOLD mode, some functions
are temporarily disabled (MAX/MIN and units selection). Press the HOLD button again to return
to normal operation.
Backlight Function
Press the / button to activate the display backlighting. Power off the meter to disable the
backlight function or press the / button again.
Self-Calibration (HCHO)
Power the meter and hold the MODE button to enter the calibration
mode. “CAL” will begin flashing on the LCD display. Note that the
calibration period is approximately 5 minutes.
IMPORTANT: Please perform the Calibration in an absolutely clean air
environment with no HCHO present.
Temperature and Humidity Offset
While the meter is off, press and hold the MODE + + + buttons all simultaneously until
the LCD shows 0.0°C and SET. Use the HOLD / button to increase the value and the /
button to decrease the value. To skip the temperature adjustment, short press the SET button.
Follow the same steps for the RH% offset. Press and hold the SET button to save the adjustment
values. The LCD will display “SAVE”. To complete the offset, reset the meter (cycle power OFF
then ON).
Note: The maximum offset ranges are ±9.9°C/F and ±9.9%RH.
www. .com [e-mail]1.800.561.8187

EXTECH INSTRUMENTS
7FM200-en-GB_V1.8 3/17
Maintenance
Low Battery
When the battery icon appears on the LCD, the batteries must be replaced.
In a downward motion, slide the rear battery compartment cover off of the meter housing.
Remove the old batteries and replace with new batteries (all of the same type) observing correct
polarity. This meter uses six (6) 1.5V AAA batteries.
Battery Safety Reminders
oPlease dispose of batteries responsibly; observe local, state, and national regulations.
oNever dispose of batteries in a fire; batteries may explode or leak.
oNever mix battery types; install new batteries of the same type.
Error Display Codes
The following errors may appear on the FM200.
ERR-1: Temperature or humidity sensor is damaged or sensor communication error
ERR-2: HCHO, Temperature, or humidity readings are out of range
If the sensor is subjected to a high concentration of HCHO or other sensitive chemicals listed in
the Sensor Cross Sensitivity table, it will read ERR2.
Let the sensor run for a few hours in clean air and the meter will read normal again.
HCHO Level Guidelines (for general reference only)
0.03 ppm Average outdoor level
0.10 ppm Recommend upper limit for residences by ASHRAE , ANSI, EPA, NIOSH for STEL
0.40 ppm Recommended upper limit for residential homes
0.50 ppm OSHA workplace limit
0.75 ppm OSHA TWA limit
0.80 ppm Level at which most people first detect odor
2.00 ppm OSHA STEL limit
www. .com [e-mail]1.800.561.8187

EXTECH INSTRUMENTS
8FM200-en-GB_V1.8 3/17
Specifications
HCHO Measurement Range 0.00 to 5.00ppm
HCHO Accuracy ±25% of reading +0.03ppm (baseline drift)
Accuracy Note: Accuracy meets NIOSH acceptance criterion within
±25% of the true value at 95% confidence level
HCHO Resolution 0.01 ppm
Temp. Measurement range 0°C to 50°C (32°F to 122°F)
Temperature Resolution 0.1°C (0.1°F)
Relative Humidity Range 10 to 90% RH
RH Resolution 0.1% RH
Temperature Accuracy ±1.0°C (2.0°F)
Relative Humidity Accuracy: ±5% (20 to 80%RH) otherwise the accuracy is ±7%
Power AAA batteries x 6 pcs or AC/DC adaptor (supplied)
Meter Dimensions 160 x 60 x 40 mm (6.3 x 2.4 x 1.6 in.)
LCD Dimensions 42 x 33.5mm (1.65 x 1.32 in.)
Weight 181.4 g (6.4 oz.)
Sensor Cross Sensitivity table
Substance
Cross Sensitivity (%)
CO
1
H2S
No Data
H2
0.1
SO2
12
NO2
No Data
NO
No Data
CL2
-3
C2H4
No Data
NH3
0.0
CO2
0.0
Ethanol, methanol
50
Phenol
7
Water Vapor
0.0*
*NB: Within specified range. Step changes in %RH produce short term
transient response
Copyright ©2014-2017 FLIR Systems, Inc.
All rights reserved including the right of reproduction in whole or in part in any form
ISO-9001 Certified
www.extech.com
www. .com [e-mail]1.800.561.8187