ExtenHD X210 User manual
Operation Manual
2x10 HDMI Splitter
Model X210
©2007 Sima Products Corporation
140 Pennsylvania Ave. Bldg #5
Oakmont, PA 15139
www.extenhd.com
ExtenHD™ is a registered trademark of Sima Products Corporation
PN 21767
TM
ExtenHD X210 User Manual ExtenHD X210 User Manual
Page 2 Page 7
One year Limited Warranty
Sima Products Corporation, (“Sima”) warrants that if the accompanying product
proves to be defective to the original purchaser in material or workmanship within
one (1) year from the original retail purchase, the Company will, at the its option,
either repair or replace same without charge (but no cash refund will be made).
What you must do to enforce Warranty
You must deliver, mail or ship the product, together with the original bill of sale, this
limited Warranty statement as proof of warranty coverage to:
Sima Products Corporation
Attn: Customer Service
140 Pennsylvania Ave., Bldg. #5,
Oakmont, PA 15139
Fax: 412-828-3775
It is recommended that you call Sima Products Corporation before sending the unit
in for service.
Limitation of Liability and Remedies
This warranty is void if any defects are caused by abuse, misuse, negligence
or unauthorized repairs. All liability for incidental or consequential damages is
specically excluded. The Company shall have no liability for any damages due to
lost prots, loss of use or anticipated benets, or other incidental, consequential,
special or punitive damages arising from the use of, or the inability to use, this
product, whether arising out of contract, negligence, tort or under any warranty,
even if the Company has been advised of the possibility of such damages. The
Company’s liability for damages in no event shall exceed the amount paid for this
product. The Company neither assumes nor authorizes anyone to assume for it
any other liabilities.
Some states do not allow for the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specic legal rights and you may have other rights, which
vary from state to state.
Caution:
IMPORTANT SAFEGUARDS FOR AUDIO PRODUCTS. PLEASE READ CAREFULLY THE
FOLLOWING IMPORTANT SAFEGUARDS THAT ARE APPLICABLE TO YOUR EQUIPMENT
1. Read instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain instructions - The safety and operating instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.
4. Follow instructions - Follow all operating and use instructions.
5. Water and Moisture - the appliance should not be used near water - for example: near a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement or near a swimming pool.
6. Ventilation - The appliance should be located so that its location or position does not interfere with proper ventilation. For
example: the appliance should not be situated on a bed, sofa, rug or similar surface that may block the ventilation openings.
7. Heat - keep away from heat sources such as radiators, registers, stoves or other heat-producing appliances .
8. Power sources - the appliance should be connected to a power supply only of the type described in the operating
instructions or as marked on the appliance.
9. Grounding or polarization. - Precautions should be taken so that the polarization or grounding means of the appliance is
not defeated. Caution: To prevent electric shock, match the wide blade of this plug to the wide slot, fully insert. Do not
use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent
blade exposure.
10. Power cord Protection - Power supply cords should be routed so they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and where they exit from
the appliance.
11. Cleaning - Wipe unit with a damp cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning
solvents or strong detergents.
12. Nonuse periods - The power cord of the appliance should be unplugged from the outlet when left unused for a long
period of time.
13. Object and Liquid entry - Care should be taken so that objects do not fall and liquids are not spilled into the enclosure
through openings.
14. Damage requiring service - The appliance should be serviced by qualied personnel when: the power cord has been
damaged, objects have fallen or liquids spilled into the appliance, the appliance has been exposed to rain, does not appear to
operate normally or exhibits a marked change in performance or the unit has been dropped or the enclosure damaged.
15. Service - The user should not attempt to service the appliance beyond that described in the operating manual. All other
servicing should be referred to qualied service personnel.
Notice to Users
The system may cause interference to a TV or radio even when it is operating properly. To determine whether the system is
causing the interference, turn it off. If the interference goes away, the system is causing the interference.
NOTE: This equipment has been tested and found to comply with the limits for
a class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be deter-mined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is needed.
•Contact your dealer for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two Conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment
©2007 by Sima Products Corp. All rights reserved. No part of this publication may be
reproduced or transmitted in any form or by any means without prior written permission
from Sima Products Corp.
ExtenHD X210 User Manual ExtenHD X210 User Manual
Introduction
ExtenHD X210 is a high performance 2 input-10 output HDMI splitter
with separate optical audio and remote control. It allows you to
connect up to 2 HDMI source and 10 HDMI displays. The 10 HDMI
outputs are identical.
Features
Two HDMI sources to connect up to 10 HDMI displays
simultaneously
HDCP keysets allows each output to work independently when
connecting to a HDMI display.
Splits a HDMI source up to 10 outputs without signal loss.
Supports DVI source and DVI display by using HDMI to/from DVI
adaptor cable.
Supports a wide range of PC and HDTV resolutions from VGA
to UXGA and 480p to 1080p. Maximum resolution bandwidth
165MHz.
Can be cascaded for more outputs
Each of the buffered output can run up to 20 Meters
@1600x1200.
Support multi channel audio.
Full HDCP Compliant.
Separate toslink output.
•
•
•
•
•
•
•
•
•
•
Connection and Installation Diagram
Page 6 Page 3
DVD or Set-Top-Box
PC
DVI to
HDMI
Cable
HDMI display
HDMI
Cable
LCD TV
HDMI
HDMI
Cable
HDTV
HDMI
HDMI
HDMI
HDMI
OPTICAL
IN
1 2
RS232
HDMI IN
EDID
STD TV
1
HDMI IN
2
HDMI OUT
1
HDMI OUT
2
HDMI OUT
3
HDMI OUT
4
HDMI OUT
5
HDMI OUT
6
HDMI OUT
7
HDMI OUT
8
HDMI OUT
9
HDMI OUT
10
OPTICAL
OUT
1 2
DC 5V
DVD
Toslink
Cable
Toslink
Cable
Amplifier
Toslink
Cable
Toslink
Cable
or or
Amplifier
Amplifier
X210 Specications
Frequency bandwidth: 1.65Gbps(single link)
Inputs: - 2x HDMI female ports (Type A connector)
- 2x Optical audio input
Output: - 10 x HDMI female port (signal link)
- 2 x Optical audio output
Power: 5VDC universal power supply
ExtenHD X210 User Manual ExtenHD X210 User Manual
Remote Control Sensor.
AUDIO IN Select/Indicator: Press the “AUDIO IN” button
sequentially to switch to your desired input audio source (HDMI,
OPTICAL 1 and OPTICAL 2), the LED will illuminate to indicate
which input source is selected.
HDMI IN Select/Indicator: Press the “HDMI IN” button
sequentially to switch to your desired input audio/video source
(HDMI 1 and HDMI 2), the LED will illuminate to indicate which
input source is selected.
HDCP Indicator: The LED will illuminate when the selected
HDMI input source is HDCP-protected.
HDMI/DVI Indicator: The LED will illuminate when the selected
HDMI input source is originally from an HDMI output, the LED will
not illuminate when the selected HDMI input source is originally
from a DVI output.
SYNC Indicator: The LED will illuminate when the selected
HDMI IN connects to an HDMI or DVI output correctly.
Key Lock: Press and hold the “POWER” button for 5 seconds
will enter the Key Lock mode, Key Lock LED will illuminate and all
buttons will not function. Press and hold the “POWER” button for
5 seconds again to disable the Key Lock mode.
POWER Switch/Indicator: Press the “POWER” button to turn
on/off the power, the LED will illuminate when the power is turned
on.
1.
2.
3.
4.
5.
6.
7.
8.
Page 4 Page 5
1 2
CHDMI-210T 2x10 HDMI SPLITTER
HDMI
INT HDCP KEY LOCKHDMI/DVI
AUDIO IN HDMI IN POWER
HDMI 1 HDMI 2 SYNC1 2
OPTICAL
34 5 6 7 8
OPTICAL
IN
1 2
RS232
HDMI IN
EDID
STD TV
1
HDMI IN
2
HDMI OUT
1
HDMI OUT
2
HDMI OUT
3
HDMI OUT
4
HDMI OUT
5
HDMI OUT
6
HDMI OUT
7
HDMI OUT
8
HDMI OUT
9
HDMI OUT
10
OPTICAL
OUT
1 2
DC 5V
Real Cable
1 2 3 6 75
4
EDID Control Jumper: Default factory setting is TV, leave as is if
the display is properly. Switch to STD if the display has problems.
HDMI Inputs 1 and 2: Connect each of the input ports to the HDMI
or DVI output of your source equipment such as DVD player or set-
top-box.
OPTICAL inputs 1 and 2: Connect each of the input ports to the
audio output of your source equipment such as DVD player or
amplier, using Toslink (optical ber) cable.
OPTICAL Outputs 1 and 2: Connect each of the output ports to
the audio equipment such as amplier using Toslink (optical ber)
cable. When both connected, the OPTICAL outputs 1 and 2 play
identical audio signal simultaneously.
RS232: 9-pin D-Sub connector for connecting to your PC or other
control console for remote control.
HDMI Outputs 1 to 10: Connect each of the output ports to the
HDMI display. When more than one output connected, the HDMI
outputs play identical audio/video signal simultaneously.
Power: Plug the 5V DC power supply into the CHDMI-210T and
connect the adaptor to AC wall outlet.
1.
2.
3.
4.
5.
6.
7.
1
2
1
3
POWER: Press the button to turn on/off the unit.
Input Select for HDMI: Press “1” button to switch
the HDMI input between HDMI IN 1 and HDMI IN 2.
Input Select for AUDIO: Press “2” button to select
HDMI INT audio input, press “3” button to select
OPTICAL 1 input, and press “4” button to select
OPTICAL 2 input
1.
2.
3.
Operation Controls and Functions
Front Panel
Rear Panel
Remote Control
Table of contents
