ExtraHop Discover 8200 User manual

© 2020 ExtraHop Networks, Inc. All rights reserved.
Deploy the ExtraHop Discover 8200
Appliance
Published: 2020-01-18
This guide explains how to install the rack-mounted EDA 8200 ExtraHop Discover appliance.
Installation prerequisites
To install the Discover appliance, your environment must meet the following requirements:
Appliance
1U of rack space and electrical connections for 2 x 750 W power supplies.
Management
One 10/100/1000 BASE-T network port for appliance management.
Monitoring (capture)
High performance interfaces: One to two network ports for connection to 25 GbE or 10 GbE sources
of packet data.
Management + monitoring interfaces: One to three network ports for connection to 1 GbE sources of
packet data.
Network Access
The TCP 443 port must be open between the Discover appliance and any system that connects to the
appliance for administration through the ExtraHop Admin UI.
For more information about the interfaces on the Extrahop appliance, see the Appliance Hardware FAQ .
Rear panel ports
EDA 8200
• One iDRAC interface port
• One RS-232 serial port to connect a console device
• One VGA port to connect an external display
• Two USB 3.0 ports to connect input devices such as a keyboard and mouse
• Two power ports to connect the appliance to an AC power source
• Four 10/100/1000 BASE-T network ports. Port 1 is the primary management port. Ports 2 - 4 are the
management + monitor ports.
• Two 25 GbE-capable ports on two network adapters. Ports 5 and 6 are the high performance monitoring
(capture) interfaces.

Deploy the ExtraHop Discover 8200 Appliance 2
Supported packet source connectivity
The Discover 8200 can accept packets through monitoring ports 2 through 6. The ports can be connected
according to the table below.
Discover 8200
Appliance Connector
Peer Connector for
Packet Source
Customer-Supplied
Cabling
Supported Operating
Speeds
Transceiver-based Connectivity
25 GbE SFP28 SR
transceiver
Multi-mode fiber
LC connectors
25 Gbps, 10 Gbps25 GbE SFP28 SR
transceiver
10 GbE SFP+ SR
transceiver
Multi-mode fiber
LC connectors
10 Gbps
Direct Attach Connectivity
Customer-supplied SFP28 DAC cable, such as the Mellanox MCP2M00-Axxx
series
25 Gpbs
Customer-supplied RJ45 Ethernet cable 1 Gbps
Set up the appliance
1. Rack mount the Discover appliance.
Install the Discover appliance in your data center with the included rack-mounting kit. The mounting kit
supports most four-post racks with either round or square holes.
2. Connect port 1 to your management network.
The EDA 8200 appliance has four 10/100/1000 BASE-T network ports. With a network patch cable,
connect the management port on the Discover appliance to your management network. Port 1 is the
default management port on the EDA 8200.
3. Connect the monitoring port.
With the appropriate network cable, connect a monitoring port on the Discover appliance to a network
tap or mirror port on the switch.
4. Optional: Connect the iDRAC port.
To enable remote management of the Discover appliance, connect your management network to the
iDRAC port with a network patch cable.
5. Install the front bezel.
You must install the front bezel if you want to configure the appliance through the LCD display.
Insert the USB connector on the right side of the bezel into the USB port on the front of the appliance.
Press and hold the release button on the left end of the bezel and push the bezel flush with the appliance
until it snaps into place.
6. Connect the power cords.
Connect the two supplied power cords to the power supplies on the back of the appliance, and then plug
the cords into a power outlet. If the appliance does not power on automatically, press the power button
on the front-right of the appliance.

Deploy the ExtraHop Discover 8200 Appliance 3
Configure the management IP address
DHCP is enabled by default on the ExtraHop appliance. When you power on the appliance, interface 1
attempts to acquire an IP address through DHCP. If successful, the IP address appears on the home screen of
the LCD.
If your network does not support DHCP, you can configure a static IP address through the LCD menu on the
front panel or through the command-line interface (CLI).
Configure a static IP address through the LCD
Complete the following steps to manually configure an IP address through the front bezel LCD controls.
1. Make sure that the default management interface is connected to the network and the link status is
active.
2. Press the select button (#) to begin.
3. Press the down arrow button to select Network, and then press the select button.
4. Press the down arrow to DHCP and then press the select button.
5. Press the down arrow to select No, and then press the select button to disable DHCP.
6. Press the down arrow to select Set static IP, and then press the select button.
7. Press the left or right arrows to select the first digit to change, and then press the up or down arrows to
change the digit to the desired number. Repeat this step for each digit you need to change. After you
configure the desired IP address, press the select button.
8. On the Network mask screen, press the left or right arrows to select the first digit to change, and then
press the up or down arrows to change the digit to the desired number. Repeat this step for each digit
you need to change. After you configure the desired network mask, press the select button.
9. On the Default gateway screen, press the left or right arrows to select the first digit to change, and
then press the up or down arrows to change the digit to the desired number. Repeat this step for each
digit you need to change. After you configure the desired default gateway, press the select button.
10. Confirm your modified network settings on the Settings saved screen, and then press any button to
return to the Network Menu.
11. Press the down arrow and scroll to Set DNS servers, and then press the select button.
12. Press the left or right arrows on the DNS1 screen to select the first digit to change, and then press the
up or down arrows to change the digit to the desired number. Repeat this step for each digit you need to
change, and then press the select button to continue to the DNS2 screen.
13. Configure a second DNS server.
14. Confirm the DNS settings on the Settings saved screen, and then press any button to return to the
Network Menu.
15. Press the down arrow twice until ← Back appears, and then press the select button.
16. Press the down arrow twice to select iDRAC. Configure the iDRAC DHCP, IP, mask, gateway, and DNS in
the same manner as the IP address.
17. Press the X button to return to the main menu.
Configure an IP address through the CLI
You can access the CLI by connecting a USB keyboard and SVGA monitor to the appliance or through an
RS-232 serial cable and a terminal-emulator program. The terminal emulator must be set to 115200 bps with
8 data bits, no parity, 1 stop bit (8N1), and hardware flow control should be disabled.
1. Establish a connection to the ExtraHop appliance.
2. At the login prompt, type shell and then press ENTER.

Deploy the ExtraHop Discover 8200 Appliance 4
3. At the password prompt, type the system serial number and then press ENTER. The serial number is
printed on a label on the back of the appliance. The serial number can also be found on the LCD display
on the front of the appliance in the Info section.
4. Enable privileged commands:
enable
5. At the password prompt, type the serial number, and then press ENTER.
6. Enter configuration mode:
configure
7. Enter the interface configuration mode:
interface
8. Run the ip command and specify the IP address and DNS settings in the following format: ip ipaddr
<ip_address> <netmask> <gateway> <dns_server>
For example:
ip ipaddr 10.10.2.14 255.255.0.0 10.10.1.253 10.10.1.254
9. Leave the interface configuration section:
exit
10. Save the running config file:
running_config save
11. Type y and then press ENTER.
Configure the Discover appliance
After you configure an IP address for the Discover appliance, open a web browser and navigate to the
ExtraHop Web UI through the configured IP address. Accept the license agreement and then log in with the
setup user account. The password is the system serial number that appears in the Info section of the LCD
display and on the label on the back of the appliance.. Enter the product key to license the appliance.
After the appliance is licensed, and you have verified that traffic is detected, complete the recommended
procedures in the post-deployment checklist .