Extreme Networks Pure Aluminum Dog Door User manual

Contact us at 1-800-531-3527 www.extremedogdoor.com
“Life is Better With Freedom”
DOG DOOR
DOG DOOR
Owner’s Manual
DOG DOORDOG DOOR

Activate Your 5-Year Warranty
1. Order #
2. Date of Purchase
3. Phone Number
4. E-mail address
You will need the following information ready to register:
eXtreme Dog Door
CONGRATULATIONS!
Register Your New
To register, go to:
www.extremedogdoor.com/register
and follow the online directions.
Thank you for your purchase, and welcome to the family.

These doors are simple to install by any handyman with common DIY
power tools. Or, you can employ the services of a professional, should
you feel the installation may be beyond your experience.
Important:
Please read the instructions in full before you proceed to install.
Should you decide to install the door by yourself, it is important that the
appropriate safety gear is worn such as protective eyewear.
Installation Steps
What’s inside the box
x6
(4x20mm)
x1 x1
x1
x1
x1

Tools Required
1 2 3 4 5 6
Drill
3/8’ (10mm) drill bit minimum
Jabsaw
Trigger clamps
Square
LevelConstruction silicone
Pencil Masking tape Measuring tape

Step
Step
1
2
Choose the installation position that
best suits your pet(s) needs. (The top
of the pet door opening should be
1” higher than the highest point on
your tallest dog’s back. The bottom of
the pet door opening should be low
enough for your smallest dog to walk
over it comfortably, but must be at
least 3” higher than the bottom of the
door you are mounting it on.)
Use masking tape to mark the bottom
of the cutout measurements for the
size door you purchased (be sure
to add 1/4” to height and to width
for sufcient installation clearance).
Use a pencil to draw out the full
rectangular cutout, as a guide for a
straight, clean cut.
x8
(3x20mm)
x6
(4x40mm)
x1 x1
x1
PETCORP 2012
4
A
A
x8
(3x20mm)
x6
(4x40mm)
x1 x1
x1
PETCORP 2012
4
A
A

Step
Step
Step
3
4
5
Step 3. Drill a hole inside each of the
four corners of your rectangle cutout
template, using a 3/8” (10 mm) drill
bit.
Using a saw (preferably a jigsaw or
reciprocating saw, but a jabsaw can
be used too), cut out the mounting
hole using your drilled holes as
starting points and your pencil outline
as a guide.
Apply a generous bead of
construction grade silicone all the way
around the perimeter of the internal
half of the dog door’s sleeve area.
x8
(3x20mm)
x6
(4x40mm)
x1 x1
x1
PETCORP 2012
4
A
A
x8
(3x20mm)
x6
(4x40mm)
x1 x1
x1
PETCORP 2012
4
A
A
x8
(3x20mm)
x6
(4x40mm)
x1 x1
x1
PETCORP 2012
4
A
A

Step
Step
6
7
Apply a generous bead of silicone
around the cutout on both sides of the
door that you’re mounting your dog
door in. This creates a weather seal.
Insert the internal and external halves
of your dog door frame into the cutout
and clamp them together tightly using
trigger clamps.
5
5
x8
(3x20mm)
x6
(4x40mm)
x1 x1
x1
PETCORP 2012
4
A
A

Step
Step
8
9
Ensure that your dog door frame is
level, and drill 1/8” (3mm) pilot holes
for your screws or rivets. These
securing points should be distributed
around the sides, top and bottom of
the overlapping sleeve joints of the
internal and external dog door frames.
Apply a silicone bead around the
outer frame of the dog door, inside
and outside, to provide a neat nish.
Apply another bead inside the frame,
where the overlapping ends, to
complete the installation with a neat
nish.
Allow the silicone beads to dry for 2
hours before removing the clamps.
The silicone should completely set in
approximately 24 hours.
5
For solid wood doors, you can use the included screws. For hollow or foam lled
doors, you can use the included rivets.
5
5

Step10
Attach the lift knob to the security
panel by feeding the nipple anchor
through the panel’s hole. On the other
side of the panel, place the washer
over the threading and twist the knob
over it in a clockwise direction until
secure.
M

“Life is Better With Freedom”
DOG DOOR
“Life is Better With Freedom”“Life is Better With Freedom”
Contact us at 1-800-531-3527
www.extremedogdoor.com