Extron electronics ACP 100 User manual

1
IMPORTANT:
Go to www.extron.com for the
complete user guide
, installation
instructions, and specifications.
ACP 100 • Setup Guide
The Extron ACP 100 Audio Control Panel is a fully congurable control interface for use with the Extron DMP 128 Plus Digital
Matrix Processor.
Each ACP 100 includes two ACP ports, which support both power and communication between the DMP 128 Plus and the
ACP100. Up to four ACP panels can be daisy-chained together for more demanding control needs.
Front Panel Features
Extron
MIC
SOURCE
1
PROGRAM
VOLUME
MUTE
SOURCE
3
SOURCE
2
MIC PROGRAM
SOURCE
1
SOURCE
3
MUTE
SOURCE
2
E
RESET
ACP 100 Front Panel with Plastic
Faceplate
ACP 100 Front Panel without
PlasticFaceplate
EEEE
CCCC
B
BBB
A
AAA
D
DDDF
FFF
Figure 1. ACP 100 Front Panel
Rear Panel Features
PWR LOAD = 0.5W
PWR LOAD = 0.5W
ON
123456
BUS ID
M
S
B
L
S
B
ON
123456
ACP
G
-
S+S
+V G
-
S+S
+V
ACP 100 Rear Panel
CCCC
D
DDD
B
BBB
A
AAA
Figure 2. ACP 100 Rear Panel
Planning the System and Installation
When planning to install an ACP system, consider how many ACP panels to use, maximum cable distance, and mounting (see
the ACP 100 product page at www.extron.com for more information about the ACP 100).
APlastic Faceplate
BFunction Buttons 1 and 2
CFunction Buttons 3-6
DVolume LEDs and Knob
EMounting Holes (4)
FReset Button
ABus ID DIP Switches
BACP Ports (2)
CACP Status LED
DMaximum Power Load Rating

2
ACP 100 • Setup Guide (Continued)
Installation
Step 1: Get Ready
Use the following checklist to prepare for the installation:
Download and install the latest version of software, rmware, and device drivers needed to congure the DMP 128 Plus and
congure the connected ACP products (see the DMP 128 Plus User Guide, available on www.extron.com, for details on
software and drivers).
Obtain cables, mounting hardware, and any other supplies required for ACP 100 installation.
Step 2: Prepare the Installation Site
ATTENTION:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
• Extron recommends installing the ACP 100 into a grounded, UL Listed electrical junction box.
• Extron recommande d’installer le ACP 100 dans un boîtier d’encastrement électrique mis à la terre, listé UL.
• If the ACP 100 will be installed into fine furniture, it is best to hire a licensed, bonded craftsperson to cut the access
hole and perform the physical installation so the surface will not be damaged.
• S’il est prévu d’installer le ACP 100 dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et
qualifié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.
• Follow all national and local building and electrical codes that apply to the installation site.
• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.
NOTE: For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the ACP 100 must
be installed in a UL Listed junction box. The end user or installer must furnish the junction box. It is not included with the
ACP100.
Americans with Disabilities ACT (ADA) Compliance
When planning where to install these devices, you may need to consider factors affecting accessibility of the button panel such
as height from the oor, distance from obstructions, and how far a user must reach to press the buttons. For guidelines, see
sections 307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 ADA Standards for Accessible Design available at
http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.
Site Preparation
Extron offers an assortment of mud rings, optional ULListed in-wall junction boxes, external
wall boxes (EWBs), and surface or tabletop mounting boxes for use with the ACP button
panels. The ACP 100 is a US 2-gang size device.
Step 3: Change Plastic Faceplate, Button Labels, or Knob
You can replace the plastic faceplate or one or more of the labels
within the buttons. Some button labels ship with the unit. You can
create and print your own customized labels using Extron
Button Label Generator software from www.extron.com.
To change a plastic faceplate or translucent button label:
1. The plastic faceplate is secured with four magnetic
catches on the underside of the plastic faceplate.
Remove the plastic faceplate by holding the body of
the unit with one hand, gripping the sides of the plastic
faceplate with the other hand, then pulling the plastic
faceplate away from the unit.
2. Gently separate the button lens cap from its white
diffuser. Insert the end of the provided Extron removal
(pry) tool into the corner notch and gently twist the tool
(see 1in the image to the right).
TEXT
Separate the
two-piece button
her
e at the corner.
Dif
fuser
Base
Insert
button label.
Button
Lens Cap
Removal
(Pry) Tool
1
2

3
3. Remove the label insert from the button lens cap.
4. Select one of the button labels from the printed label sheet included with the unit. Remove the label from its backing and
remove the clear protective lm from the front of the label.
5. Insert the button label into the button lens cap (see 2in the image on the previous page).
6. Align the button lens cap with the white diffuser and the panel opening, then press the button lens cap into place on the
button.
7. Attach the plastic faceplate to the ACP 100. Align the openings of the faceplate with the buttons and knob and place the
plastic faceplate against the unit. The four magnetic catches fasten the faceplate onto the unit.
To change a knob:
1. Remove the plastic faceplate as described at the bottom of the previous page.
2. Firmly grasp the knob and pull it away from the ACP 100.
3. Align the ridge inside the new knob with the channel on the knob control and allow the magnet in the knob to snap into place.
4. Reattach the plastic faceplate to the unit as described in step 7 above.
Step 4: Set Bus ID Addresses
Set the bus identication DIP switches for the ACP 100 and any other ACP panels being connected to the system. Each ACP
device must have a unique bus ID (address). If other ACP panels have the same bus ID, address conicts may cause one or more
of the panels to not be recognized in DSP Congurator or by the DMP 128 Plus. Up to four ACP devices can be connected in the
same system.
ON
123456
BUS ID
M
S
B
L
S
B
ON
123456
PWR LOAD = 0.5W
ACP
G
-
S+S
+V G
-
S+S
+V
+
V+
S G
–
S
ACP Ports
• Connect up to four (4) ACP endpoint devices per
DMP 128 Plus.
• Wire the connectors the same at both ends.
• These ports are identical. You can connect devices
interchangeably to either port.
• Do not exceed a total of 1000 feet (305meters) of cable for
connections between the DMP 128 Plus and all of the ACP
panels.
• Power is provided by the DMP 128 Plus, a PS 1220EB
power inserter, or an Extron 12 VDC power supply.
Bus ID Address DIP Switches
• Use these DIP switches to set the six-bit, binary
bus address for the ACP 100.
• Each ACP connected to the same DMP 128 Plus
must have a unique address.
• Switch 1 (on the left) is the highest value (32, the
the most signicant bit [labeled “MSB”]).
• Switch 6 (on the right) is the lowest (1, the least
signicant bit [labeled “LSB”]).
• Up = on = 1, Down = off = 0
Examples:
010010
ON
123456
000001
1
ON
123456
18Unit address
DIP switches
Binary address
ACP Diagnostic LED Indications
LED unlit — No power is present at the ACP.
LED blinking slowly — Power is present, but communication
with the DMP 128 Plus is not confirmed.
LED blinking fast — There is an ACP bus ID address conflict.
LED lit steadily (solid) — Power and communication are
confirmed.
ACP port on a
DMP 128 Plus, or
on another ACP
endpoint
Figure 3. ACP 100 Rear Panel Bus ID

4
ACP 100 • Setup Guide (Continued)
Each ACP device in a system must have a
unique bus ID which represents a six-digit
binary number. ACP bus IDs are set by using
the DIP switch assembly on the rear panel of
the ACP 100.
Switch 1 on the left sets the most signicant bit (highest number, 32) while switch
6 on the right sets the least signicant bit (the lowest number, 1). See the example
addresses in the table to the right.
Step 5: Cable All Devices
1. Connect the ACP panel to the DMP 128 Plus.
2. Connect ACP panels to each other if multiple panels are being used in the
control system (see gure 4 below for correct wiring).
NOTES:
• Wire both ends of each ACP cable the same. Connectors are
interchangeable between DMP 128 Plus and ACP device.
• Do NOT power an ACP panel from more than one power source.
3. Apply power to the DMP 128 Plus.
Cabling
Attach cables using the diagram below as a guide. Wiring is the same for all ACP
models. Connect a 4-pole captive screw connector to each end of the cable,
wiring both ends the same. In most cases, the ACP devices are powered by the
DMP128Plus. Power is carried on the V+ pin of the ACP 100 and other ACP
devices.
Extron STP20-2/1000 or STP20-2P/100 cable is recommended for ACP device
connections.
G
-
S
+S
+V
Ground
+Signal
- Signal
+12 VDC
Black
and
Drains
Green
White
Red
G
-
S+S
+V
Drain Wires
Basic ACP Connector Wiring
Figure 4. Basic ACP Connector Wiring
Slide
1 2 3456
ON
M
S
B
L
S
B
BUS ID
Example Addresses
Bus ID
(Decimal)
Binary
Address
DIP Switch
Setting
0 000000*
*Reserved
(for controller
address)
1 2 3456
ON
M
S
B
L
S
B
BUS ID
1 000001
1 2 3456
ON
M
S
B
L
S
B
BUS ID
2 000010
1 2 3456
ON
M
S
B
L
S
B
BUS ID
3 000011
1 2 3456
ON
M
S
B
L
S
B
BUS ID
4 000100
1 2 3456
ON
M
S
B
L
S
B
BUS ID
5 000101
1 2 3456
ON
M
S
B
L
S
B
BUS ID
6 000110
1 2 3456
ON
M
S
B
L
S
B
BUS ID
7 000111
1 2 3456
ON
M
S
B
L
S
B
BUS ID
8 001000
1 2 3456
ON
M
S
B
L
S
B
BUS ID

5
ACP devices that are relatively far from the host DMP 128 Plus can be connected to an optional Extron PS 1220EB eBUS power
inserter or an Extron 12 VDC desktop power supply as shown in the diagrams below and on the next page (see the ACP 100
Specifications at www.extron.com for cable length to determine if additional power is recommended).
ATTENTION:
• Always use a power supply supplied or specified by Extron. Use of an unauthorized power supply voids all regulatory
compliance certification and may cause damage to the supply and the unit.
• Utilisez toujours une source d’alimentation fournie par Extron. L’utilisation d’une source d’alimentation non autorisée
annule toute conformité réglementaire et peut endommager la source d’alimentation ainsi que l’unité.
• If not provided with a power supply, this product is intended to be supplied by a UL Listed power source marked
“Class2” or “LPS” and rated output 12VDC, minimum 1.0A.
• Si ce produit ne dispose pas de sa propre source d’alimentation électrique, il doit être alimenté par une source
d’alimentation certifiée UL de classe 2 ou LPS et paramétré à 12VDC et 1,0A minimum.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities.
• Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une utilisation dans les espaces d’aération
ou dans les cavités murales.
• The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA70,
article725 and the Canadian Electrical Code part1, section16. The power supply shall not be permanently fixed to
building structure or similar structure.
• Cette installation doit toujours être en accord avec les mesures qui s’applique au National Electrical Code ANSI/
NFPA70, article725, et au Canadian Electrical Code, partie1, section16. La source d’alimentation ne devra pas être
fixée de façon permanente à une structure de bâtiment ou à une structure similaire.
eBUS 24 WATTS MAX
100-240V 50-60Hz
0.6A MAX
+
V+ S G
–
S
+
V+ S G
–
S+ V+ S G
–
S+ V+ S G
–
S
+
V+ S G
–
S+ V+ S G
–
S
ACP port on
an ACP or
other ACP
endpoint
device
+
V+
S G
–
S
LAN
DMP 128 Plus C
RxTx G
RS-232
+S+V -S G
56 78
12 34
OUTPUTS
DMP EXP
ACP
REMOTE
USB AUDIO RESET
LAN
Rx
Tx
G
R
S
-23
2
REMOT
REMOT
REMOT
REMOT
REMOT
REMOT
REMOT
REMOT
E
E
E
E
E
E
E
E
US
B AUDI
O
R
E
S
E
T
D
MP 128 Plus
C
5
6
7
8
1
2
3
4
OUTP
U
T
S
DMP E
DMP
E
XP
XP
DMP 128 Plus
X
G - S+S
G - S+S
Tie drain wires
to ground.
G - S+S
X
G
- S
+S
+V
Ground
+Signal
- Signal
+12 VDC
G - S+S
+V
ACP Connections
• Connect up to four (4) ACP
endpoint devices to the PS 1220EB.
• Wire the connectors the same at
both ends.
• All ports are identical and
interchangeable.
Power Input
(100-240 VAC,
50-60 Hz)
PS 1220EB
ATTENTION: Do NOT connect the power
pin to any device that is already powered
by the DMP 128 Plus or by an additional
power suppl y.
3/16" (5 mm) Max.
Figure 5. Cabling ACP Devices with a PS 1220EB Power Inserter

6
ACP 100 • Setup Guide (Continued)
ACP port on a
host DMP 128
Plus
+
V+
S G
–
S
ACP port on
an ACP 100
or other ACP
device
+
V+
S G
–
S
G
- S
+S
G
Ground
+Signal
- Signal
+12 VDC
+V
G-S+SG-S+S
+V
- S
+S
Tie drain wires to ground.
Ground
all devices.
– Return
+12 VDC input
Ridged
Smooth
1AMAX
100-240V 50-60Hz
External
Power Supply
(12 VDC, 1 A max.,
Extr
on P/N 28-071-57LF)
ACP 100
Rear Panel
NOTE: Check the polarity of the power
supply before connecting it to the ACP.
Power Input,
External Power Supply (optional)
• Connect to an Extron 12 VDC, 1 A,
power supply.
3/16" (5 mm) Max.
Figure 6. Cabling ACP Panels with an Extron 12 VDC, 1 A Power Supply
Step 6: Configure the System
NOTE: For complete information on creating configuration files and operating DSP Configurator, see the DMP 128 Plus User
Guide and the DSP Configurator Help file.
1. Create a new DMP 128 Plus conguration le in DSP Congurator and create all groups, presets, and macros that will be
controlled by the ACP device.
2. Open the Configure ACPs dialog box in DSP Congurator and congure the buttons on the ACP devices connected to
the DMP 128 Plus.
3. Connect to the DMP 128 Plus in Live mode and push the conguration le to the device.
Step 7: Test and Troubleshoot
1. Verify that the DIP switches on the ACP devices are set to the desired address on each unit and that there are no bus ID
address conicts in the system. As mentioned in the rear panel features diagram in step 4, the ACP LED lights steadily
when power and communication are present and there are no bus ID address conicts.
2. Verify cables to and from the ACP devices are wired the same at each end.
3. Test the system:
a. Press the buttons on the ACP devices and ensure the buttons light as desired and that the appropriate control
commands or functions are triggered. Commands can be veried in DSP Congurator or DataViewer, if responses are
congured.
b. Ensure that the audio output responds correctly to the volume knob. Also ensure that the volume LEDs light correctly
as you increase or decrease audio gain.
4. Make adjustments to wiring, bus ID addresses, or system conguration as needed. Remember that the rear panel ports and
DIP switches will not be accessible after the ACP is mounted. If needed, push a revised conguration to the ACP device via
the host DMP 128 Plus.
If you have questions during installation and setup, call the Extron S3 Sales and Technical Support Hotline or the Extron S3
Control Systems Support Hotline [phone]).

7
ACP 100 • Setup Guide (Continued)
Step 8: Mounting the ACP 100
Prior to mounting:
1. If it has not already been done, feed all device cables through the wall or furniture and, if applicable, through the plastic
spacer.
NOTE: If the unit is not installed in a mud ring, you must install the plastic spacer. The spacer positions the unit to allow
the magnetic catches on the plastic faceplate to attach properly and securely.
2. Ensure the cables are connected to the ACP 100 rear panel.
Mount the ACP 100 as follows:
1. Insert the cabled ACP 100 into the mud ring or junction box within the wall or furniture, aligning the mounting holes in the
ACP 100 with those in the box or mud ring.
2. Secure the ACP 100 in the junction box, wall or surface mounting box, or mud ring as follows (see 1in the gures below).
a. Insert the included screws through the oval slots at the top and bottom of the ACP 100 metal mounting plate, through
the plastic spacer (if not using a mud ring), and into the corresponding threaded holes in the box or mud ring.
b. Using a Phillips screwdriver, gently tighten the screws until snug.
3. Attach the plastic faceplate to the ACP 100. Align the plastic
faceplate openings with the buttons, knob, and LEDs and
place the plastic faceplate against the metal mounting
plate (see 2in the gures below). The magnetic
catches fasten the plastic faceplate onto the
metal mounting plate.
Extron
VOLUME
22
1
1
Wall
Wall
Box
Plastic
Faceplate
Metal Mounting
Plate
Plastic Spacer
Extron
VOLUME
22
1
1
Metal Mounting
Plate
Wall Mounting
Bracket
(Mud Ring)
Plastic
Faceplate
Wall
Figure 7. Installing the ACP 100
in a Junction Box
Figure 8. Installing the ACP 100
in a Mud Ring

8
68-3065-50 Rev. A
01 17
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX
Extron Europe
+800.3987.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
EExtron Australia
+61.8.8113.6800
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2017 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com