Extron electronics VersaTools MTP DA4 User manual

IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions before connecting the
product to the power source.
IMPORTANT:
Go to www.extron.com for the
complete user guide and installation
instructions before connecting the
product to the power source.
MTP DA4 and DA8 • Setup Guide
This guide provides basic instructions for
J9
Disable
Mute
(Default)
or Enable
Mute
J3
Serial or Audio
(Default)
an experienced installer to set up and operate
the Extron MTP DA distribution amplifier.
Pre-installation — Jumpers
See figure 1at the right or see “Termination
and Mute Jumpering” in the MTP DA4 and
DA8 User Guide for more information.
NOTE: The jumpers have no effect when
the DA is part of an MTP CV/SV series, or
VTT001/VTR001 system.
Jumper J3
This sets the DA to properly terminate RGB video as well as the audio (default) or serial
portion of the input signal.
Jumper J9
This sets the DA to always pass the audio or serial link regardless of the contact closure
mute status (default). It can also be set to mute the audio or serial link when its video mute
function is activated.
Use 2 mounting holes on
opposite corners.
1/2 Rack Width False Front
Face Plate
(2) 4-40 x 3/16" screws
6" Deep Rack Shelf
MTPDA SERIES
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources
and mount the MTP DA as required. A mounting
example is at the right (see figure 2). See “Mounting”
in the user guide for more mounting options.
Step 2 — Input from the Transmitter
Terminate a TP cable as shown in figure 3. Connect
the cable into a MTP transmitter and into the AV
12
34
A/V INPUT A/V OUTPUTS
Insert
TP Wires
Pins:
12345678
input connector.
Step 3 — Outputs to the Receivers
Terminate up to four or eight (depending on
model) TP cables as shown in figure 3. Connect
the cables into the DA AV output ports and into
receivers that are compatible with the transmitter.
NOTES: •The inputs and outputs should be
terminated using the same standard on both
ends of the cable.
• Only use the TIA/EIA T568A standard
when using Enhanced Skew-Free™ AV cable.
Pin T568 A
Wire Color
T568 B
Wire Color
1 White-green White-orange
2 Green Orange
3 White-orange White-green
4 Blue Blue
5 White-blue White-blue
6 Orange Green
7 White-brown White-brown
8 Brown Brown
Figure 1. Jumpers
Figure 2. 6-inch Deep Rack
Shelf Mount
Figure 3. TP Cable Termination
MTP DA4 and DA8 • Setup Guide
This guide provides basic instructions for
J9
Disable
Mute
(Default)
or Enable
Mute
J3
Serial or Audio
(Default)
an experienced installer to set up and operate
the Extron MTP DA distribution amplifier.
Pre-installation — Jumpers
See figure 1at the right or see “Termination
and Mute Jumpering” in the MTP DA4 and
MTP DA8 User Guide for more information.
NOTE: The jumpers have no effect when
the DA is part of an MTP CV/SV series, or
VTT001/VTR001 system.
Jumper J3
This sets the DA to properly terminate RGB video as well as the audio (default) or serial
portion of the input signal.
Jumper J9
This sets the DA to always pass the audio or serial link regardless of the contact closure
mute status (default). It can also be set to mute the audio or serial link when its video mute
function is activated.
Use 2 mounting holes on
opposite corners.
1/2 Rack Width False Front
Face Plate
(2) 4-40 x 3/16" screws
6" Deep Rack Shelf
MTPDA SERIES
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources
and mount the MTP DA as required. A mounting
example is at the right (see figure 2). See “Mounting”
in the user guide for more mounting options.
Step 2 — Input from the Transmitter
Terminate a TP cable as shown in figure 3. Connect
the cable into an MTP transmitter and into the AV
12
34
A/V INPUT A/V OUTPUTS
Insert
TP Wires
Pins:
12345678
input connector on the DA.
Step 3 — Outputs to the Receivers
Terminate up to four or eight (depending on
model) TP cables as shown in figure 3. Connect
the cables into the DA AV output ports and into
receivers that are compatible with the transmitter.
NOTES: •The inputs and outputs should be
terminated using the same standard on both
ends of the cable.
• Only use the TIA/EIA T568A standard
when using Enhanced Skew-Free™ AV cable.
Figure 1. Jumpers
Figure 2. 6-inch Deep Rack
Shelf Mount
Pin T568 A
Wire Color
T568 B
Wire Color
1 White-green White-orange
2 Green Orange
3 White-orange White-green
4 Blue Blue
5 White-blue White-blue
6 Orange Green
7 White-brown White-brown
8 Brown Brown
Figure 3. TP Cable Termination

MTP DA4 and DA8 • Setup Guide (Continued) MTP DA4 and DA8 • Setup Guide (Continued)
68-975-50
Rev. C 1211
68-975-50
Rev. C 12 11
Extron USA Headquarters Extron USA - West Extron USA - East
+800.633.9876 (Inside USA/Canada Only) +1.714.491.1500 +1.919.863.1794
+1.714.491.1517 FAX [phone] FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
Extron USA Headquarters Extron USA - West Extron USA - East
+800.633.9876 (Inside USA/Canada Only) +1.714.491.1500 +1.919.863.1794
+1.714.491.1517 FAX [phone] FAX
© 2011 Extron Electronics All rights reserved. www.extron.com
Step 4 — Power
Wire the 2-pole captive screw connector for the external
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
AA
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max
.
12 VDC power supply as shown in figure 4. Plug it into
the DA.
Operation — Mutes
To mute an output, tie the Output Mute pin to the
ground ( ). To mute all outputs, tie the A pin to the
ground (see figure 5for more information).
1 2 3 4 5 6 7 8 A
MTP DA8
Output Mute Connector
1 2 3 4 A
MTP DA4
Output Mute Connector
Pin Contact Closure Function
1 Out #1 Mute output #1
2 Out #2 Mute output #2
3 Out #3 Mute output #3
4 Out #4 Mute output #4
5 Out #5 Mute output #5
6 Out #6 Mute output #6
7 Out #7 Mute output #7
8 Out #8 Mute output #8
A Out All Mute all output
Gnd Ground
Figure 4. Power Connection
Wiring
0.5AMAX
12V
POWER
+
-
OUTPUTMUTE
12345678A
INPUT 1 2 345 6 7 8
OUTPUTS
OUTPUT
SHARP
LR
INPUT VIDEO
12V
0.5aMAX
MTPRSV A
OUTPUT
SHARP
L R
INPUT VIDEO
12V
0.5aMAX
MTPRSV A
OUTPUT
SHARP
L R
INPUT VIDEO
12V
0.5aMAX
MTPRSV A
OUTPUT
SHARP
LR
INPUT VIDEO
12V
0.5aMAX
MTPRSV A
INPUT
MTPT SV A RCA
VIDEO OUTPUT
L R
12V
0.5aMAX
Flat Panel
Display
Extron
MTP DA8
Twisted Pair
Distribution Amplier
Up To
8 Receivers
Extron
MTP T AV RCA
Twisted Pair
Transmitter
DVD
Extron
MTP R AV
Twisted Pair
Receivers
TP Cable
TP Cable
Figure 5. Mute Connector and Pinout
Figure 6. Example of a Typical MTP DA8 Application
Step 4 — Power
Wire the 2-pole captive screw connector for the external
Power Supply
Output Cord
SECTION A–A
Ridges
Smooth
AA
Captive
Screw
Connector
Tie Wrap
3"
16 (5 mm) Max
.
12 VDC power supply as shown in figure 4. Plug it into
the DA.
Operation — Mutes
To mute an output, tie the Output Mute pin to the
ground ( ). To mute all outputs, tie the A pin to the
ground (see figure 5for more information).
1 2 3 4 5 6 7 8 A
MTP DA8
Output Mute Connector
1 2 3 4 A
MTP DA4
Output Mute Connector
Pin Contact Closure Function
1 Out #1 Mute output #1
2 Out #2 Mute output #2
3 Out #3 Mute output #3
4 Out #4 Mute output #4
5 Out #5 Mute output #5
6 Out #6 Mute output #6
7 Out #7 Mute output #7
8 Out #8 Mute output #8
A Out All Mute all output
Gnd Ground
0.5AMAX
12V
POWER
+
-
OUTPUTMUTE
12345678A
INPUT 1 2 345 6 7 8
OUTPUTS
OUTPUT
SHARP
LR
INPUT VIDEO
12V
0.5aMAX
MTPRSV A
OUTPUT
SHARP
L R
INPUT VIDEO
12V
0.5aMAX
MTPRSV A
OUTPUT
SHARP
L R
INPUT VIDEO
12V
0.5aMAX
MTPRSV A
OUTPUT
SHARP
LR
INPUT VIDEO
12V
0.5aMAX
MTPRSV A
INPUT
MTPT SV A RCA
VIDEO OUTPUT
L R
12V
0.5aMAX
Flat Panel
Display
Extron
MTP DA8
Twisted Pair
Distribution Amplier
Up To
8 Receivers
Extron
MTP T AV RCA
Twisted Pair
Transmitter
DVD
Extron
MTP R AV
Twisted Pair
Receivers
TP Cable
TP Cable
Figure 4. Power Connection
Wiring
Figure 5. Mute Connector and Pinout
Figure 6. Example of a Typical MTP DA8 Application