Extron electronics 650 UT User manual

1
IMPORTANT:
Go to www.extron.com for the
complete user guide
, installation
instructions, and specifications.
Cable Cubby 650 UT • Installation Guide
This guide provides instructions for an experienced installer to install and connect the
Extron Cable Cubby 650 UT.
The Cable Cubby 650 UT units are under furniture mountable and are expandable for cable
access, connections, and AC power.
Planning
Check with local and state regulations before starting the
installation
Ensure that the planned installation complies with building and electrical codes.
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.
Check all parts and equipment before installation
Ensure that all parts are present in each kit.
Ensure that necessary tools and equipment are available for the installation.
Determine the number for Cable Cubby 650 UT enclosures you intend to install.
Kit Contents
125V~ 12A MAX TOTAL
Cable Cubby 650 UT
1
4
1
1
(6) 3/8", (2) 1/4"
1
1
4
#6 Pan-head Mounting
Screws and Star Washers
AAP Frame Plate
Cable Grommet Plate
Connectivity Bracket
Connectivity Bracket
AAP Frame Plate
Cable Grommet Plate
#6 Pan-head Mounting Screws and Star Washers
Hole Plugs
Hole Plugs
#4-40 Module Screws
#4-40 Module Screws
Retractor Bracket
Retractor Pin & Clip
Retractor Pin and Clip

Cable Cubby 650 UT • Installation Guide (Continued)
2
Preparing the Table
Cut a hole in the surface where the enclosure will be installed. The size of the hole depends on the number of enclosures used
(see cut-out dimensions on the nextpage). Ensure the sides of the hole are smooth after cutting and finished before
installing. Read the following information before making a cut.
Determine the best location for the enclosure
Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.
Ensure that there is ample space under the table for cables. Allow at least 36 inches of cable loop for each cable (see Routing
and Connecting Cables on page 7).
When installing Retractors in the Cable Cubby, ensure that there is enough space for the Retractor assembly under the table
or furniture.
22.95"
(583 mm)
26.47"
(672 mm)
21.28"
(540 mm)
12.23"
(311 mm)
9.23"
(234 mm)
30
30
Table Top
Series/2
Series/2
9.0"
(229 mm
)
15.14"
(385 mm)
21.14"
(537 mm)
Series/2 XL
Series/2 XL
3.0"
(76 mm)
3.0"
(76 mm)
28.95"
(735 mm)
NOTES:
•To prevent objects from impeding cable retraction, allow at least 3 inches of clearance from the exposed cable side of
the enclosure (see the diagrams below).
•Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or
entanglement (see Routing and Connecting Cables on page 7).

3
Cut the hole in the table and pre-drill mounting holes
CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.
ATTENTION : Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut
conduire à une blessure à l’oeil.
ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople.
Exercise care to prevent scarring or damaging the furniture.
ATTENTION : L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et
qualiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.
For one or two enclosures, the cut-out dimensions and mounting hole locations are shown below. For more enclosures, multiply
the length accordingly. If necessary, pre-drill into the furniture at the keyhole and mounting hole locations.
NOTE: Diagrams shown above are not drawn to scale.
Dimensions and cut-out templates are available online at www.extron.com.
10"
(254 mm)
SURFACE
CUT-OUT
AREA
1
/
16
" (1.5 mm)
4
1
/
4
"
(108 mm)
+
-
Mounting Holes (16)
11.5"
(292 mm)
12"
(305 mm)
5"
(127 mm)
SURFACE
CUT-OUT
AREA
1
/
16
" (1.5 mm)
4 1/4"
(108 mm)
+
-
1.5"
(38 mm)
7"
(178 mm)
1.5"
(38 mm)
3"
(76 mm)
6"
(152 mm)
6.5"
(165 mm)
6.5"
(165 mm)
Mounting Holes (8)
6"
(152 mm)
6.5"
(165 mm) 3"
(76 mm)
1.5"
(38 mm)
1.5"
(38 mm)
Keyholes (4)
Keyholes (2)
2.0"
(51 mm)

4
Option 2: Cable Pass-Through Module
Secure the grommet
plate on the connectivity
bracket, using four of the
provided module screws.
2
Insert cables through the
bottom of the connectivity
bracket and into the holes
of the grommet plate.
Snap the included
hole plugs into
any unused holes.
1
3
Insert “Show Me”
Cables into the
grommet plate.
1
Attach the “Show Me” Cable Trim Plate
to the top of the module, using the
module screws.
2
Attach the grommet
plate to the bottom
of the module, using
the module screws.
3
Option 3: Retractor Bracket
Secure the bracket using four of
the provided pan-head mounting
screws with star washers. Tighten
the screws using a screwdriver.
Insert the bracket as shown.
The bracket may be installed on the left
or right side of the enclosure and at the
lowest height.
2
1
left
t
he
Preparing the Cable Cubby
Step 1 (Only for multiple enclosures) — Assemble Enclosures
Option 1: AAP Module
Secure up to three single-space
AAPs in the AAP plate.
Secur
e the AAP plate on the connectivity brackets,
using four of the provided module screws.
#4-40 Nut with
Captive Washer
Insert cables through the bottom of the connectivity bracket.
Connect cables to the AAPs.
1
3
2
Step 2 — Assemble Connectivity Modules
Connectivity modules allow you to populate the Cable Cubby enclosure with a combination of AAPs, cable pass-through, or
Retractors. Follow the steps below to assemble the connectivity modules of your choice.
Using a #2 screw driver,
unscrew the four pan-head
screws that attach the enclosure
sides of the Cable Cubby together.
Repeat this step on the corresponding
side of the other enclosure.
Detach side panels of both enclosures.
1
Before attaching the enclosure, ensure the
keyhole mounting holes are orientated in the
same direction.
Attach the enclosures together
with the four pan-head mounting screws
and washers that were removed in step 1.
2
Repeat steps 1 and 2 to
add more enclosures to
the extension.
3
NOTE: The opening of the bracket should be
installed towards the outside of the enclosure.

5
Cable Cubby 650 UT • Installation Guide (Continued)
125V~ 12A MAX TOTAL
Secure the modules using
four of the provided pan-head
mounting screws and star washers.
2
Insert the modules
into the Cable Cubby.
1
Step 3 — Install the Modules
Determine where the connectivity module and/or power module will be installed in the
Cable Cubby. The modules may be installed on the left or right side of the enclosure and
at various heights.
For the power module:
WARNING: Risk of Electric Shock. To ensure
proper electrical grounding, use the provided #6-32
mounting screws with the star washers.
AVERTISSEMENT : Risque de choc électrique.
An d’assurer une mise à la terre correcte, utilisez les
xations de mise à la terre #6-32 et les rondelles en
étoile fournies.
125V~ 12A MAX TOTAL
125V~ 12A MAX TOTAL
2
Hook the Cable Cubby assembly
onto the screws at the keyhole locations,
as shown at right.
Slide the Cable Cubby assembly
into slot.
Align the other mounting
holes on the assembly with
the pre-drilled holes on the
furniture.
Tighten the screws to
secure the Cable Cubby
assembly.
Insert a mounting screw appropriate for
the furniture material into each of the keyhole locations.
Tighten each screw until it protrudes 1/4 inch from
the bottom of the table.
1
3
Insert and tighten the rest of the mounting screws
through remaining mounting holes on the enclosure
and into the pre-drilled holes in the furniture.
Mounting holes
Mounting the Cable Cubby under the Table
Align the enclosure with the pre-drilled holes under the furniture. Secure the enclosure with the appropriate screws (see Cut the
hole in the table and pre-drill mounting holes on page 3).

6
Cable Cubby 650 UT • Installation Guide (Continued)
Angular Mounting
Remove the enclosure screws as shown above, then follow
this step:
Horizontal Mounting
See the Cable Retractor Setup Guide, available on the
Extron website, for additional steps.
Remove two enclosure screws
(one on each side) from this position.
Then, mount the Retractors as shown
at left.
Cable Release
Assembly
Move the cable release assembly upward until
the angular mounting hole is visible. Reinstall the
enclosure screws in this hole (both sides).
Remove two enclosure screws
(one on each side) from this position.
Then, mount the Retractors as shown
at left.
Cable Release
Assembly
Move the cable release assembly upward until
the angular mounting hole is visible. Reinstall the
enclosure screws in this hole (both sides).
Installing Retractors
Follow the steps below to install Retractors. For horizontal or angular Retractor mounting, see the information below at right, then
follow the steps below.
Insert the included pin through the
Retractor mounting hole on the side
of the Retractor assembly bracket.
Secur
e the clip
to the pin.
Insert Retractors into
the Retractor bracket. Secure the locking screw
on each Retractor. Do not
overtighten.
2
3
1
4
Optional Double Retractor bracket mounting:
Install brackets as shown at right. Two double
Retractor brackets can mount up to four
Retractors.
Alternative Retractor Configuration for Cable Cubby 650 UT
Cable Cubby 650UT
Side View
E
E
Secure the brackets using four of
the provided pan-head mounting
screws with star washers. Tighten
the screws using a screwdriver.
Insert the brackets as shown.
The bracket may be installed on
the left or right side of the enclosure
and at the lowest height.
2
1
e

7
Routing and Connecting Cables
For cable pass-through applications,
allow at least 36 inches (0.9 m) of cable
loop for each cable.
Connect cables to the AV system
and connect the AC power cord.
Using zip ties, secure cables to the holes
on the bottom of the Cable Cubby.
1
2
3
NOTE: Ensure that there is no tension on the power cable.
CAUTION:
Risk of Electric Shock.
This equipment must be grounded.
ATTENTION :
Risque de choc électrique.
Cet équipement doit être xé au sol.
Installation Checklist
Planning (page 1)
Check with local and state regulations before starting the installation
Check all parts and equipment before installation
Determine number of enclosures to install
Preparing the Table (page 2)
Determine the best location for the enclosure
Verify sufcient space under furniture
Cut a hole in the table and pre-drill mounting holes (page 3)
Preparing the Cable Cubby (page 4)
If applicable, assemble enclosures
Assemble connectivity modules
Install the modules (page 5)
Mounting the Cable Cubby (page 5)
Mount the Cable Cubby under the table
Installing Retractors (page 6)
Remove Retractor screws for horizontal and angular mount applications
Install Retractors into the bracket
Routing and Connecting cables (page 7)
Dress cables under the table
Connect cables to the AV system

8
68-3062-50
Rev. A
04 17
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
Extron Australia
+61.8.8113.6800
+61.8.8351.2511 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2017 Extron Electronics All rights reserved. www.extron.com