EZ-ON SHS-3120 User guide

Check the door status
1) You can install the doorlock only when the thickness of it is 1 3/8˝~1 3/4˝(35
to 44 mm). (In case of installing with an auxiliary steel plate, its thickness is
also included.)
2) Check whether the dead bolt and strike can be installed or not. (door distor-
tion, location of the drilling hole, etc.)
Installation Quick GuideInstallation Quick Guide
SHS-3120 Door Lock
01
AA Batteries (LR6)
User Manual /
Installation Quick Guide
Dead Bolt Strike
Outdoor Body
Product Components Installation Procedure
Insert the dead bolt
1) Insert the dead bolt from the side of the door.
2) Rotate the dead bolt to adjust the center hole to be horizontally aligned from
outside.
3) Fix the dead bolt by using two 4×15 screws.
03
Perform drilling
1) Check the location and direction of the drilling template sheet, attach the
sheet, and mark on it with a pen. (a, b)
2) Check the location and direction for the dead bolt, attach the drilling template
sheet on the side of the door, and mark on it with a pen.
3) Drill a 1˝(25 mm) hole by using a hole cutter. (a)
4) Drill pilot holes by using a 1/8˝(3.5 mm) drill bit. (c, d)
5) Drill a pilot hole that is within 2 1/8˝ (54 mm) by using a drill bit. (b)
02
Indoor Body Fixing Panel
Turn Shaft Magnet
Check the door status
1
1
Perform drilling
2
2
Insert the dead bolt
3
3
Insert the outdoor body
4
4
Connect the xing panel
5
5
Connect the turn shaft
6
6
Set for the left or right hand
7
7
Check the dead bolt operation
8
8
Fix screws for the indoor body
9
9
Check the door lock operation
10
10
Ⱍⲻ
#03&ⲻ%*"
-"5$))0-&
ⲻ%&&1
'PMEJOH-JOF
'PMEBMPOHUIJTMJOF
BOEBMJHOJUUPUIF
DPSOFSFEHFPGUIF
EPPS
ⲻ
Supplied 4x15 wood screws are for a wooden door only. In case of a steel door,
different type of screws are required.
Ϩ


Ϩ


FRONT VIEWLEFT VIEW
ⓐⓑ
ⓒ
ⓓ
Card
No. Screw Quantity Description
1 FH+ M5×20 3Out Housing + Plate In Fastening
2 OH+ M4×22 2Out Housing + Deadbolt + Plate In Fastening
3 FH+ T4×25 5 Plate In + Wooden Door Fastening
4 FH+ M3×6 4 In Housing + Plate In Fastening
5 FH+ U10-24×9 4 Deadbolt, Striker, Iron Door Fastening
6 FH+ T4×15 4 Deadbolt, Striker, Wooden Door Fastening
GC68-01188A

SHS-3120 Door Lock
Connect the fixing panel
1) Detach the xing panel from the indoor body.
2) First fasten two parts (a, b) 90% by using M4×22 screws.
3) Fasten the xing panels (c, d, and e holes) by using three M5×20 screws.
4) Align the outdoor body with the xing panel after making them vertically
crossed and fasten them by using ve screws.
05
Check the dead bolt operation
Connect the cable to the indoor body.
08
Connect the turn shaft
While the dead bolt is open, insert the turn shaft in the indoor-to-outdoor direction.
06
Set for the left or right hand
Insert the magnetic sensor from the indoor body’s rear and adjust the switch.
(To the magnetic sensor insertion direction)
07
Fix screws for the indoor body
1) Open the battery cover of the indoor body. (There are screw grooves at the
upper left and right corners.)
2) Fasten screws at the upper room area by using two M3X6 screws. (a, b)
3) Fasten the left and right screws on the indoor body by using two M3×6
screws. (c, d)
10
Check the door lock operation
Insert four alkaline batteries into the indoor body and check the door lock
operates correctly after referring to User Guide.
11
Setting for left hand
Insert the outdoor body
Insert the outdoor body in the outdoor-to-indoor direction.
(You must insert the outdoor body after aligning it with the center hole of the
dead bolt.)
04
ⓐ
ⓒ
ⓔ
ⓑ
Setting for right hand
L R L R
ⓓ
Check the dead bolt operation
1) Place the knob of the indoor body to face the magnetic sensor.
2) Loosely insert the indoor body into the outdoor body from the room side.
3) Check the dead bolt of the indoor knob moves properly and the knob rotates
correctly in the open or close direction.
09
ⓐⓑ
ⓒ
ⓓ
※ Install the magnatic sensor in accordance
to the direction of dead bolt.
(The role of magnetic sensor is to check
the close/open state of door.)