EZee Life 170 Tilt & Recline User manual

170 Tilt & Recline
Rehab Shower Commode

2
Contents
Assembly 3
Adjustments 5
Operating Information 6
Safety Information 8
Inspection Items 9
Warranty 10
Specifications:
Frame Material – Aluminum
Seat Tilt Range – 0° to 13° from level
Lower Back Recline Range – 90° to 111° from seat position
Upper Back Angle – 15° posterior to lower back position
Lower Leg Support Range– 90° to 50° from seat position
Weight – 46.5 lbs (21.1 kgs)
Wheels – 5” Locking Casters
Seat Width – 18”
Seat Depth – 17”
Seat Height – 21.8” - 23.8” (adjustable)
Footrest Hanger Angle – 60°
Footrest Length – 14” to 20” (Infinite adjustment)
Back Height – 16”
Arm Height – 8” (from seat)
Arm Length – 12.5”
Arm Pad Length – 11.75”
Weight Capacity – 286 lbs (130 kgs)

3
Assembly Instructions
1. Slide seat belt loops (1) onto each side of
backrest (2) posts.
2. Insert two back support posts (1) into seat frame (2)
and tighten two hand wheels (3).
3. Insert four caster stems into holes in the four corners of the
bottom of the frame.
4. Set the seat height by aligning the caster stem holes
(1) with the desired adjustment holes (2) in the
frame and inserting the locking pin (3) to secure the
caster.
5. Insert the anti-tippers into the two anti-tipper receiver
tubes located at the rear of the frame above the casters.
Ensure the push pins have popped through the set
receiver holes.

4
6. The adjustment is made by simply depressing the anti-
tipper push pin (1), sliding the inner anti-tipper tube
(2) to the desired length, aligning the push pin with the
closest adjustment hole (3) and allowing it to pop
through.
(The anti-tippers should be as close to the floor as possible
without catching on doorway thresholds, changes in floor
levels or other obstacles.)
7. To attach the footrest (1) to the commode lower the
footrest pivot plug (2) into the top of the front seat
frame (3) with the foot plate (4) off to the side of the
commode. Then swing the footrest to the forward
position where it will lock in place.
8. The foot plate height can be adjusted by loosening the
footrest clamp (1), sliding the foot plate extension tube
(2) up or down inside the footrest hanger tube (3) and
re-tightening the clamp.
DO NOT extend the footplates past the MAX line (4) stamped into the foot
plate extension tubes. The MAX line should not be visible.
9. From the back of the commode slide the commode
pail into the pail support channels (1) located on the
bottom of the seat pan (2).
10. Install the adjustable head rest (1) by inserting and
vertical support tube (2) into the headrest bracket (3)
mounted on the commode push bar and then insert
the horizontal support tube (4) through the end
bracket (5) of the vertical tube (2).

5
Adjustments
Headrest – The headrest on this commode is referred to as an “X”
headrest and the smaller end of the “X” is at the bottom to support the
neck where it meets the back of the skull.
The arms of this style of headrest can be flexed in or
out as needed by simply pulling them apart or
squeezing them together to provide more control or
more freedom as needed.
The angle of the headrest can also be adjusted by
loosening the three Hex screws (1) holding the
horizontal support tube (2), pivoting the head rest to
the desired position, and re-tightening the Hex screws.
Anti-Tippers – The anti- tippers are required to prevent the commode
from tipping backwards when it is tilted back or when the user is self-
propelling with the optional 24” wheels.
They can be flipped up or removed when necessary to clear obstacles but
should be in place as often as possible to prevent accidental tipping of the
commode.
Tilt Mechanism Cables – The cables (1) that allow the
chair to tilt may over time stretch. This
is normal and can be adjusted by loosing the lock nut
(2), turning the adjustment screw (3) counter
clockwise and re-tightening the lock nut.

6
When adjusted properly, the distance between
the strut release lever (5), and the cable anchor
(6), should be about 1”.
If the chair angle cannot be changed when the
tilt lever (4) is pressed the cause is usually out of
adjustment or stretched cables. If the chair will not
lock at any angle the cables are likely adjusted too
tight.
Footplate Adjustment – Proper footplate adjustment is required
for comfort and reduction of pressure points. If the footplates are
positioned too high pressure is increased on the buttock area; if they are
too low, pressure is increased on the backs of the legs just above the
knees and the feet are left dangling.
See item 8 on page 4 for adjustment procedure.
Operating Instructions
Arms – The arms of the commode can be flipped
up and back to aid in transfers or access by
caregivers for bathing. The arms will stay raised
when raised all the way.
When doing a side transfer to or from the
commode only the arm on the side the transfer is being done on should
be raised.
Seat Belt – The seat belt supplied with the commode is known as a side
release seat belt. To undo the buckle simply depress both release tabs at
once and pull the two sides apart.
To do up the seat belt slide the prongs into the
receiver until they click into position.
Do not leave clients unattended in the commode.

7
Footrests – The footrests can be removed by pushing
the release lever (1) swinging the footrests out to the
side, or into the middle, and lifting straight up.
To replace the footrests, lower the footrest pivot plug
(2) into the commode seat frame holes (3) from the
side on the center of the seat and swing the footrests to the front until
they lock into position.
Headrest – The headrest can be removed to aid in
transfers by loosening the Headrest clamp on the
commode push bar.
Tilt & Recline – The tilt/recline feature of the 170 rehab shower commode
can be used to reduce tone and for comfort of those users who have
balance control problems or may move about in the seat too much to be
safe when the seat is level.
To activate the tilt/recline mechanism the caregiver
grasps the commode push bar and squeezes the
release lever (1). When the release lever is
squeezed, two gas struts mounted on the side frames
that hold the seat in position are released and the
seat can be positioned at the angle
wanted. Letting the release lever out will lock
the seat at the angle set.
Important: When the release lever is squeezed the seat will move freely.
The caregiver must have the push bar of the commode firmly grasped
when activating the release lever to prevent the seat from pitching
forward possibly injuring the user.
The user should always wear the provided seat belt for safety while sitting
in this commode.

8
Casters – The 180 and 185 shower commodes come standard with 4
locking 5” swivel casters that allow the commode to be turn a full circle in
its own length and be pushed in any direction required. This is particularly
important feature when the commode has to be used in areas where
there isn't much room for manoeuvring.
To lock the casters the caregiver uses their steps
on the lock lever (1).
To release the wheellock the caregiver pushes
down on the release lever (2) with their foot.
When the casters are in the locked position the swivel
feature also locks for safety.
Safety Information
Never operate the tilt mechanism without having a firm grip on the commode
push bar. The gas struts used to aid in tilting the commode need to be
controlled while changing the tilt angle to prevent the chair from pitching
forward.
Ensure back rest is securely attached before using.
To avoid tipping, DO NOT attempt to reach objects if you have to move forward
in the seat to do so.
To avoid tipping, DO NOT attempt to reach objects if you have to pick them up
from the floor by reaching down between your knees.
To avoid tipping, DO NOT lean over the top of the back upholstery to reach
objects behind you, as this may cause the commode chair to tip over.
To avoid tipping, DO NOT shift your weight or sitting position toward the
direction you are reaching.

9
DO NOT attempt to stop, or slow, a moving transport chair with wheel locks.
Wheel locks are not brakes.
DO NOT climb, go up or down ramps or traverse slopes greater than 5 degrees
(1:12 grade).
Travel up and down slopes and inclines. DO NOT travel across inclines.
Use caution on slippery surfaces.
DO NOT transfer into, or out of, the shower commode chair on slippery floors.
Ensure wheel locks are engaged and wheels are positioned outward before
transferring into or out of the shower commode.
DO NOT stand on foot plates.
DO NOT stand on seat.
Always use the supplied seat belt for safety.
Always have the arms flipped down if the user has upper body stability
problems.
Always use supplied anti-tippers for users who are known for rocking in their
seats.
DO NOT leave users unattended in the shower chair.
DO NOT overload this transport chair. The weight capacity is 300 pounds
including the user and any things they may be carrying.
Inspection Items
Ensure the commode chair rolls straight (no excessive drag or pull to one side).
Inspect the seat, back and arms for tears and/or damage.
Inspect for any loose or broken hardware or parts.
Inspect for cracked, broken or loose wheels.
Ensure the hand brakes are easy to engage and prevent the wheels from
turning.

10
Limited Warranty
Ezee Life products carry a two-year warranty against manufacturing defects,
faulty materials, and workmanship only.
Any alterations, misuse, abuse, or accidental damage voids this warranty.
Healthline reserves the right to replace or repair any part that has become
defective.
The warranty does not extend to consequential costs resulting from the fault
or defect of the product: freight and travel costs, loss of earnings, or other
expenses that one may incur.
Warranty is valid for the original purchaser only and the original receipt must
be presented before any warranty options are considered. Please also be
prepared to provide the date of purchase and serial number.
Distributed by:
Canada - HPU Medical Wholesale
15-34 Futurity Gate, Concord, Ontario L4K 1S6
Toll Free: 888-634-5808 Fax: [phone]
USA - Healthline Products
1065 E Story Rd., Winter Garden, Florida 34787
Toll Free: 800-987-3577 Fax [phone]
Version 2021-01-28