EZT3D T1 User manual

T1 MANUAL
Shenzhen EnZhuoTe Technology Co.,Ltd

Warning Specifications
The extruderand hotbed of 3D printer would work in high temperature condition.
Do not touch the parts by hand directly. Even after the printing finished, the
working parts will still be in a high temperature state fora while. Please be patient
to wait for the cooling of the working parts and printed mode.
3D printercontains high-speed working parts, so please be careful not be clamped.
Please use 3D printer in an open and well-ventilated environment.
Please keep 3D printer away from water.
The temperature for using 3D printer is recommended for 8℃~ 40℃，humidity
20%~50%,if exceed the scope,it may bring bad print results.
In case of emergency, please unplug to turn off the powerof the 3D printerdirectly.

Layout Sketch Map of Packaging
Number
Name
Number
Name
A1 A packet of acrylic _1_ A packet of screws
A2 200mm long rod _2_ Connecting line
A3 Power line _3_ Pulley accessories
A4 Tool kit _4_ Limit switch
A5 Material frame _5_ Extrusion head support
C1 Top panel _6_ Extrusion head accessories
C2 Bottom panel _7_ Belt
C3 Hot bed _8_ Pipe
J 2020 Aluminium parts _9_ Winding rope+cable ties.
D LCD screen F1 Extruder
E Main board F3~F4 Motors of x&y&z rod
H Test Filament G Power supply
1、Please check the parts according to the list above.
2、Find the Memory
_ card, copy the software and instruction files
from the card to the computer, and please assembly and use the 3D
printer according to the instruction files.
3、If there is any question, please feel free to contacting us for
technical support.

Checkbeforestart
You should level the print platform at the
first time before
printing.

Leveling I ns t ruc t i o n Of T1
Note:
1. You should level the print platform at the first time before printing.
2. Please clean the nozzle before leveling, ensure that no other residual
material.
3. For the convenience of adjusting the gap between extruder head and
print
platform, please use an A4 paper to drag between them if moving
smoothly.
Step 1. Intelligent leveling
See the LCD display, enter to the menu and then select “Setting” ->
“Intelligent leveling”, Each testpoint using rotary knob to reduce the gap
between the extruder head and the paper.
NOTE: Using Rotary knob to adjust the gap between the extruder head and the
paper
Step 2. Confirmation
Select the test file in Memory_card to start simulated print. Pay attention to the
gap between nozzle and plate when working, the “
reset- bottom” should be
pressed when the gap too low or too high between
nozzle and Hotbed. Then
adjust Z-height by
using rotary knob to select “Setting”->”Z-Height”.

Gap is too narrow
between nozzle and
Hotbed, reduce the Z-
height by 0.1~0.3mm
Gap is too large
between nozzle and
Hotbed, increase the Z-
height by 0.1~0.3mm
Perfect Z-height

Tips for Buyers
Dear Buyer:
First of all, thanks for buying products. In order to help you
install and use our products more easily , here we provide some
tips might help you.
1.Before installation, make sure all parts are in good condition
and no damage during delivery.
2.For environment purpose, we do not offer more paper
instruction, all instruction files are loaded in Memory card
which included in the package, please find the memory card
and check all the files on your computer, if there is any
instruction files missed, please contact us to get them.
3. Any problem on the 3d printer(quality issue, damage, missed,
not working, etc), please take some photos or video on it, and
send photos and video to your vendor, so that the after-sales
engineer could study your problem carefully and then to
provide you the right solution and fix the problem perfectly,
thank you very much .
Now, start to print your designs and have fun!
--- EZT3D Co., Ltd.