Faber VICO Assembly instructions

installation guide and user manual
free-standing gas fireplace
40 010 528
02 28
VICO
Saturnus 8 NL-8448 CC Heerenveen
Postbus 219 NL-8440 AE Heerenveen
T. [phone]
F. [phone]
“Log Burner Technology”

UK/IRL
1
CONTENTS
1. INTRODUCTION 2
2. SAFETY INSTRUCTIONS 3
3. INSTALLATION REQUIREMENTS 5
3.1 Flue requirements 6
3.2 Terminal position 9
4. INSTALLATION-INSTRUCTIONS 13
4.1 Preparation of the appliance 13
4.2 Placing the appliance 15
4.3 Placing of the wood set 17
5. INSTALLATION OF THE FLUE 18
5.1 Connection of the flue 18
5.2 Remote control 19
5.3 Installation 20
6. COMMISIONING 22
6.1 Check pilot ignition 22
6.2 Functional burner checkr 22
6.3 Functional balanced flue check 23
6.4 Check reference pressure 23
7. HANDING OVER 24
8. SERVICING 25
8.1 Routine annual servicing 25
UUSSEERR GGUUIIDDEE33
9. SAFETY INSTRUCTIONS FOR THE USER 34
10. CONTROLING THE APPLIANCE 36
11. CLEANING AND SERVICE INSTRUCTIONS 42
12. DISPOSAL OF THE PACKAGING AND THE APPLIANCE 43
INDEX 1 LIST OF SPARE PARTS 30
INDEX 2 TECHNICAL DATA 31

UK/IRL
2
UK/IRL
3
1. INTRODUCTION
NNoottee::tthheessee iinnssttrruuccttiioonnss sshhoouulldd bbee rreeaadd ccaarreeffuullllyy aanndd rreettaaiinneedd ffoorr
ffuuttuurree rreeffeerreennccee..
PPlleeaassee lleeaavvee tthheessee iinnssttrruuccttiioonnss wwiitthh tthhee uusseerr..
Special features:
- Realistic flame and glow effect because of the "Log burner"
technology.
- Room sealed room appliance, inlet and outlet are led to the outside
using a natural draught concentric pipe system (100 mm/150 mm
(no power fan required . No additional ventilation required.
- Air supply and flue-gases go to outside atmosphere through wall or
roof. A maximum horizontal extension of 6 meters is possible.
- Remote Control option on all appliances.
- Meets the essential requirements of the European Gas Appliance
Directive (GAD and carries the CE mark.
2. SAFETY AND GENERAL
INFORMATION
Before installation, ensure that the local distribution conditions
(identification of the type of gas and pressure and the adjustment of
the appliance are compatible.
This gas appliance is factory set and shall not be adjusted by the
installer.
This appliance does not contain any component manufactured from
asbestos or any asbestos related products.
The pilot and flame sensing device fitted to this fire is also a safety
device. If for any reason any part of the pilot assembly is to be
replaced the entire assembly including the pilot burner, thermocouple,
electrode and injector must be exchanged complete for a pilot assembly
from the original manufacturer only.
Ventilation
This appliance is room-sealed and doesn't require purpose provided
ventilation.
2.1 General safety
It is the law in the UK that aallllgas appliances, are installed by a
competent person in accordance with the Gas Safety (Installation and
Use Regulations (as amended , the relevant British Standards for
Installation work, Building Regulations, Codes of Practice and the
manufacturers instructions.
The installation should also be carried out in accordance with the
following where relevant:
BS5871 Part1 BS5440 Parts 1 & 2 BS1251.
Building Regulations Document J (as applicable .

UK/IRL
3. INSTALLATION REQUIREMENTS
N te:
Since the appliance is a source of heat, circulation of air occurs.
Therefore it is of importance that you do not use the appliance
shortly after a renovation of the home. Because of the natural
circulation of air, moist and volatile components from paint, building
materials, carpet etc. will be attracted. These components can settle
themselves down onto cold surfaces in the form of soot. As on all
heat producing appliances, soft furnishings such as blown vinyl
wallpaper placed to near to the appliance may become scorched or
discoloured. This should be born in mind when installing the
appliance.
Dimensions:
For the dimsensions: see figure 1.
Minimum distance between the appliance and rear wall is 50 mm and
between appliance and sidewall min. 250 mm.
A
-
A
65.100
114.100
361
272
143 283 G3/8"
72
30
322
1115
1155
250min.
50
min.
478
542
224
ø150
ø100
470
A
A
fig. 1
UK/IRL
4
Building Regulations and Standards issued as relevant by the
Department of the Environment or the Scottish Development Department.
In the Republic of Ireland installation should be carried out in
accordance with IS813, ICP3, IS327, Building Regulations, Codes of
Practice, the manufacturers instructions and any other rules in force.
Failure to comply with the above could leave the installer liable to
prosecution and invalidate the appliance warranty.
Safety instructions for the user: see chapter 9.
5

UK/IRL
7
UK/IRL
6
3.1 Flue requirements
The appliance is of the type C11/C31. The appliance will need to be
supplied with the approved flue pipes and terminal, it is not possible to
supply your own.
The minimum effective height of the flue system must be 0.5 m.
Terminal locations, through the wall as well as through the roof. See
figure 3.
Flue routing;
- a horizontal extension with elbows is allowed for a maximum of 6
meter (depending on the type and situation .
- vertical max. 12 meter.
Determine on the base of the table 2 and 3, depending on the type
and terminal position, if the desired situation is possible.
To establish this you will need to calculate:
-The effective height (this is the real difference in height between the
upper side of the appliance and the terminal .
- The total horizontal extension. This is the total horizontal flue length
where:
• each elbow, which is in the horizontal area, counts for 2 meters.
• each 45-degree bend, which is in the horizontal area, counts for 1
meter.
• elbows and bends at the transition of horizontal to vertically are
not to be counted.
• the wall mounted terminal counts for 1 meter.
FFlluuee rreessttrriiccttoorr
If applicable, in the table is also stated the size of a flue restrictor.
This restrictor needs to be fitted in the combustion chamber when
placing the appliance ( see chapter 4.2 . Normally the smallest flue
restrictor is fitted.

UK/IRL
9
UK/IRL
8
0123456
0XXXXXXX
XXXXXX
XXXXX
XXXX
XXX
XX
X
XXXXX
0XX
0,5 X 0
1 X 30 0 0
000
1,5 40 30 0 0
240300 0 0 0 0
3404030 0 0 0 0
4 50404030 0 0 0
5 505040403030 0
6 505050404030 0
7 605050404040
8 6060505050
960
60 60 50
10 65 60 60
11 65 65
12 65
X combination
not allowed
0 remove flue restrictor
45 mm
30 mm flue restrictor
50 mm
flue restrictor
60 mm
65 mm flue restrictor
Horizontal extension
Effective height
flue restrictor
flue restrictor
Determine according to the table the right total horizontal- and vertical length.
When meeting an X, and when the values are outside the table, the combination is not
allowed.
3.2 Terminal p siti n
Verify if the required terminal position meets the local installation
regulations regarding disturbance, good functioning and ventilation.
(Also see: safety requirements .
NNoottee::
The terminal must be located so that the outlet is not obstructed. If
the flue terminal is located within 2 meters of a footway, path or
where people could come into contact with it then a suitable terminal
guard must be fitted.
Terminals located close to shared walkways, footpaths etc. could be
subject to legal constraints and this should be pointed out to the
customer before installation. If in any doubt about flue location
advice should be sought from local building control, or if appliance-
related, from the manufacturer including wherever possible a
dimensioned sketch.
fig. 3
fig. 2a
Hvert.
N
M
L
K
J
I
H
fig. 2b
Hvert.
A
F
G
E
D
C
B
Calculati0n h riz ntal extensi n fig. 2a:
Flue lenght C + E = 1 + 1 2 m
Elbows D = 1 x 2 mtr 2 m
Total horizontal extension 4 m
Measure r calculate effective height
(Hvert)
Flue lenght A 1 m
Roof mounted terminal 1 m
Total effective height 2 m
When calculating on basis of the table:
Allowed but without flue restrictor.
Remove the flue restrictor!
Calculati0n h riz ntal extensi n fig. 2b:
Flue lenght J + L = 0,5 + 0,5 1 m
Elbows K + M = 2 x 2 mtr 4 m
Terminal 1 m
Total horizontal extension 6 m
Vertical
Flue lenght H 1 m
When calculating on basis of the table:
Combination not allowed.
Example calculati n 1:
Example calculati n 2:

UK/IRL
11
UK/IRL
10
3.2 Terminal p siti n (c ntinuing)
Avoid locating the terminal in close proximity to plastic materials
such as gutters or other combustibles. If this is unavoidable then a
suitable deflector should be made.
Some important requirements for a good functioning are:
The wall-mounted terminal has to be at a distance of at least 0,5
meters off:
- Corners of the building.
- Below eaves.
- Balcony's etc. unless the duct is dragged to the front side of the
overhanging part.
The roof mounted terminal has to be at a distance of at least 0,5
meters of the sides of the roof, excluded the ridge.
Flue terminal p siti ns
Dimension TTeerrmmiinnaall ppoossiittiioonnBalanced flue room sealed
(kW input 0-7 kW expressed in net Natural draught
A Direct below an opening, airbrick, 300 mm
opening windows, etc.
B Above an opening, airbrick, 300 mm
opening window ect.
C Horizontally to an opening, airbrick, 300 mm
opening window etc.
D Below gutters, soil pipes or drain pipes 500 mm
E Below eaves 500 mm
F Below balconies or car port roof 600 mm
G From a vertical drain pipe or soil pipe 300 mm
H From an internal or external corner 600 mm
I Above ground roof or balcony level 300 mm
J From a surface facing the terminal 600 mm
K From a terminal facing the terminal 600 mm
L From an opening in the carport (e.g. 1200 mm
window into the dwelling
M Vertically from a terminal on the same wall 1500 mm
N Horizontally from a terminal on the same wall 300 mm
P From a vertical structure on the roof 600 mm
Q Above intersection with roof 500 mm
Table 4

UK/IRL
13
4. INSTRUCTIONS FOR INSTALLATION
4.1 Preparing the appliance
1. Locate the appliance in the right position, min distance 50 mm from
rear wall and 250 mm from a side wall.
2. Open the door by first loosening the locking screw in the door
handle, then pull down the handle (See fig. 4 .
locking
A
A
fig. 4
Example f h w terminal p siti n is measured
UK/IRL
12

UK/IRL
15
UK/IRL
14
4.2 Placing the appliance
Gas connection
1. - Installation pipes should be in accordance with BS 6891. Pipe work
from the meter to the appliance must be of adequate size.
2. - The complete installation including the meter must be tested for
soundness and purged as described in the above code.
3. - A means of isolation must be provide in the supply to facilitate
servicing.
4. - If applicable remove the receiver and disconnect the wires from
the gas valve
5. - Remove the cover plate (see fig 6 . Unfasten the 4 screws on both
sides, hold the ash pen tray horizontal while removing the cover
plate.
6. - The connection should be made in 8 mm copper or similar semi
flexible tube (max. 1 meter . Ensure that the gas pipe does not
interfere with the removal or replacement of the burner tray of the
controls.
7. - The gas connection is nut and olive suitable for 8 mm pipe.
fig. 6
4.1 Preparing the appliance (c ntinuing)
3. Take the box with the log set out of the combustion chamber.
4. Place the right flue restrictor in the combustion chamber. To
determine the right flue restrictor, see chapter 3.
A
A
fig. 5

UK/IRL
17
UK/IRL
16
4.3 Placing the l g set
On the bottom of the logs is a identification:
• 1 dimple first log left placed over the burner and resting on the
burner tray.
• 2 dimples placed in the middle over he burner and resting on the
burner tray.
• 3 dimpels the right side log placed over the burner and resting on the
burner tray.
Never place extra elements of any kind into the combustion chamber.
To guarantee good combustion, the log set may only be installed in
the way specified by Faber International. Any other arrangement can
lead to soot on logs or window. Do not use the fire with broken or
missing logs.
fig. 8
4.2 Placing the appliance (c ntinuing)
2. Points of attention for placement:
- Locate the appliance before assembling the flue.
- Painted flue pipes available.
- see also chapter 5 Flue installation
3. Check if the safety hatch on top of the combustion chamber is in
the right position and seals the combustion chamber properly (it
has to be air tight.
4. Place the log set (see placing log set, chapter 4.4 .
5. Spread, the bags of embers (imitation ashes provide with the
appliance over the burner tray. AAtttteennttiioonn!!No embers under the logs
the logs have to rest on the burner tray!
6. Close the door and fixate the position of the handle by placing
back the screw in the door handle.
A
A
fig. 7

UK/IRL
19
UK/IRL
18
5.2 Rem te c ntr l (if applicable)
The remote control is only meant to regulate the flames, it functions
only when the pilot burner is ignited. It is therefore not possible to
ignited the appliance with the remote control or to shut-off the pilot-
flame.
The radio-frequency remote control is intended for fireplaces installed
in a domestic setting in all EU countries except Austria, Denmark,
Finland and Greece.
Features:
- Manual control will always remain possible.
- The remote control is a radio frequency type and has been approved
internationally.
- The remote control generates a unique safety code every time you
activate the transmitter, its similar to those used in a car.
- The remote control is easy to install retrospectively.
5. INSTALLATION OF THE FLUE
5.1 C nnecti ns with use f c ncentric duct material
- There are painted flue sections available for the flue run in the
room.
- Build the system starting from the appliance on.
- Make a hole of ø 153 mm for the wall or roof mounted terminal.
- Make sure you place the pipes in the right direction, the narrow
end towards the appliance.
- Make sure the pipes are fixed sufficiently, a wall clamp every 2m, so
the weight of the pipes is not resting onto the appliance.
- The outside of the pipe can become hot (140 degrees . Stay 50 mm
away from wall surface or sealing. Make sure to provide sufficiently
heat resistant isolation when going through the wall or roof.
- Because of expansion or cooling down the concentric pipes can turn
loose. It is recommended to fix the spring clip with a self tapping
screw at inaccessible places.
- To get the exact measure flue length you can use cut down-
concentric pipe, wall mounted terminal or roof mounted terminal. To
obtain a smoke sealed connection, the inner pipe must be 20 mm
longer then the outside pipe.
- The horizontal pipes need to rise away from the appliance at a rate
of 3 degrees per metre.

UK/IRL
21
UK/IRL
20
Setting the right transmissi n c de
The receiver has to learn the code from the transmitter, which is already
done at the factory. However the code disappears if the receiver is
disconnected from the mains for a longer period.
1. Set the on/off switch on the receiver to "on".
2. Push the "mod" button on the receiver and hold it for 3 seconds.
3. The green control lamp will light up and stay on. Repeat this step
if it doesn't.
4. Push a button on the remote control. The control lamp on the
receiver should now go out.
5. Again push a button on the remote control. The lamp starts
flashing and will switch off eventually.
6. The receiver now recognizes the remote control. The remote
control now functions.
7. Check if you can hear a sound and the motor runs when you
push a button on the remote control.
5.3 Installati n rem te c ntr l
1. Connect the mains adapter to the receiver box. The adapter is set
to the correct voltage in the factory 4.5V.
2. Slide the receiver box into the holder.
3. Connect the wires to the gas valve (see fig. 10 .
4. Set the on/off switch on the receiver to "on".
fig. 10
fig. 9

UK/IRL
23
UK/IRL
22
6.3 Functi nal balanced flue check
1. Set the appliance on max. input.
2. Verify the flame picture, this means no flames against the
window, the flame have to come besides the logs, if not check
the log layout.
3. Check if the flames are yellow after 10 minutes of operation. If
you still have a blue flame or the appliance goes out check:
- If the flue pipes are fitted correctly (no leakage .
- If the wall mounted terminal is placed with the correct side up.
- If the correct flue restrictor is installed.
6.4 Check reference pressure
The appliance is preset to give the correct heat input.
No further adjustment is necessary. Fit a pressure gauge at the test
point D to check the burner pressure.
The pressure should be checked with the appliance alight and at max
input.
The ccoollddsetting pressure should be as shown at the technical data
page 31.
After checking the pressure, turn off the appliance. Remove the
pressure gauge and close the sealing screw. Re-light the appliance.
Turn to max. input and test around the test point D for gas
soundness using a suitable leak detection fluid.
C D
DC
AB
BA
fig. 12
6. COMMISSIONING (functi nal checks)
6.1. Check pil t igniti n
1. Push in and turn the control knob (A from {anticlockwise to
the setting (small flame . You will hear a tick meaning there is
ignition. Hold the knob in and wait for a few seconds while the air
is purged.
2. Bring the knob back in the start position and turn the knob several
times to the position. Check that the pilot has lit.
3. Continue to hold in the control knob for a further ten seconds to
ensure that the pilot flame is stable.
4. Release the knob. The pilot should remain alight.
6.2 Functi nal burner check
1. Turn knob (B to max. clockwise.
2. Turn the knob (A more anticlockwise to the position (large
flame . Now it is possible to light the main burner.
3. Turn knob B anticlockwise to max. The main burner should light.
Check for gas soundness at all joints with leak detection floud!
4. Check the ignition of the main burner on low and high setting.
5. Turn knob B clockwise till {. The main burner is off.
6. Turn the knob A to {. The pilot should go out.
AB
fig. 11

UK/IRL
25
UK/IRL
24
8. SERVICING
To ensure safe, efficient operation of the appliance, it is necessary to
carry out routine servicing at regular intervals.
It is recommended, that the fire is inspected/serviced by a competent
person at least once a year.
IImmppoorrttaanntt
TTuurrnn ooffff tthhee ggaass ssuuppppllyy bbeeffoorree ccoommmmeenncciinngg aannyy sseerrvviicciinngg.. AAllwwaayyss tteesstt
ffoorr ggaass ssoouunnddnneessss aafftteerr rreeffiittttiinngg tthhee aapppplliiaannccee.
8.1 R utine annual servicing
1. Clean (if necessary :
- the pilot system;
- the burner;
- the combustion chamber;
- the glass.
2. Check the log lay and replace the embers (if applicable .
3. Do the functional test as described at page 22.
4. Check the flue system and terminal on damage and soundness
(visual inspection .
7. HANDING OVER
(final check and cust mer briefing)
77..11Instruct the customer on the full operation of the appliance.
77..22..11Advise the customer how to clean the appliance including the
glass.
77..22..22Instruct the customer on the operation of the remote control,
including replacement of batteries and how to set the right
transmissions code.
77..22..33Hand over these instructions including the user guide to the
consumer.
77..22..44Recommend that the appliance should be serviced by a
competent person at least once a year.

UK/IRL
27
UK/IRL
26
8.2. Burner tray assembly
1. Open the door and remove remote control, log set, grid and burner
tray cover.
2. Remove the cover plate (see fig 6 . Unfasten the 4 screws on both
sides, hold the ash pen tray horizontal while removing the cover
plate.
3. Break the gas supply at the 8mm connection inside the appliance.
4. Unscrew the burner assembly and take them out of the combustion
chamber.
A. Pilot assembly
B. Burner
C. Fixation plate
D. Injector
E. Gas control
B
A
C
D
E
fig. 13
8.1.1 Cleaning the glass
Depending on the intensity of use , you can get a deposit on the
glass. This can be removed with a special ceramic glass cleaner
(ceramic cook-top cleaner as follows:
1. Open the door as described at 4.1.
2. Clean the glass. Handle the glass with clean hands, wear
gloves, if possible try to avoid fingerprints on the glass.
3. Close the door and fixate the door handle.
AAtttteennttiioonn::Before closing the door : check the sealing rope is in good
condition. Be sure that there are no fingerprints on the glass. It is
not possible to remove those prints after you burn the appliance for
a while (they are burnt in .
8.1.2 Cleaning the c mbusti n chamber
Remove the logs before cleaning.
Clean the combustion chamber with a vacuum cleaner.
If the burner is visibly damaged, replace the burner.

UK/IRL
29
UK/IRL
28
8.3 CCoommbbuussttiioonn tteesstt
A BS7967 combustion analysis check should be carried out using an
analyser to BS7927 positioned in the flue outlet.
A Ratio of CO/CO2 should be less than 0.01 within 30 minutes.
(100ppm CO per 1% CO2 .
A reading of CO in the room centre should give a rise of less than
9ppm over ambient, peak reading.
Gas c ntr l bl ck
A Governor
B Adjusting screw pilot flame
C Inlet pressure test point
D Burner pressure test point
Pr pane c nversi n
For conversion from propane to natural gas, order for a propane
burner unit.
Please give the serial number from the data plate when you order.
AB
BA
C D
DC
fig. 14

UK/IRL
31
UK/IRL
30
UK/IRL
LIST OF SPARE PARTS
VVIICCOO
DDeessccrriippttiioonnCCoommppaannyy ppaarrtt
Glass 04508600
Burner NG 20523305
Burner propane 20523335
Log set 20786120
Receiver 20604000
Remote control 20603900
Adapter 20900142
Motor (remote control 37003086
Gas control NG 37003089
Spark wire 06017300
Spark electrode 06006600
Pilot burner assembly NG 20900145
Thermocouple 37002033
Pilot burner assembly propane 20900154
Embers 20900019
Lack-spray for combustion chamber 09000008
Lack-spray other parts 09000012
UK/IRL
TECHNICAL DATA
VICO
Country UK/IRL UK/IRL
Category II2H3+ II2H3+
Appliance type C11 / C31 C11 / C31
Reference gas G20 G30/G3
Input (nett kW 7,1 6,9
Efficiency class 2 2
Inlet pressure mbar 20 30/37
Gas Rate 15 °C / 1013 mbar m3/h 0.75 0.215 or 0.5 kg
Reference burner pressure mbar 12 23
Injector size mm 3x 1.5 3x 0.9
Reduced input restrictor mm 2.1 1.1
Pilot assembly
Type SIT 160 SIT 160
Code Nr 51 Nr 30
Flue system
MV size 100-150 mm 100-150 mm
Pre installed flue restrictor mm 30 30
Gas control GV36-C5AOEHC68M GV36-C5AODHC68M
Remote control
Adapter 230VAC/50HZ/5VA 230VAC/50HZ/5VA
Voltage adapter V 4.5 4.5
Batteries remote control 2 x LR03 2 x LR03
Alkaline long life Alkaline long life
Gas connection 8 mm nut and olive 8 mm nut and olive
Dimensions: see figure 1

UK/IRL
33
USER GUIDE
UK/IRL
32

UK/IRL
35
UK/IRL
34
IIMMPPOORRTTAANNTT
A suitable Fireguard conforming to BS6539 and BS6778 should be used
with this appliance to protect children, the elderly or infirm. Care
should also be taken with pets.
In your own interest and that of safety, all gas appliances must be
installed by competent persons. Installation must be in accordance with
National Regulations. CORGI registered installers are required to work to
recognised standards.
NNoottee:
Since the appliance is a source of heat, circulation of air occurs.
Therefore it is of importance that you do not use the appliance shortly
after a renovation of the home. Because of the natural circulation of air,
moist and volatile components from paint, building materials, carpet etc.
will be attracted. These components can settle themselves down onto
cold surfaces in the form of soot. As on all heat producing appliances,
soft furnishings such as blown vinyl wallpaper placed too near to the
appliance may become scorched or discoloured. This should be born in
mind when installing the appliance.
9. SAFETY INSTRUCTIONS FOR THE
USER
9.1 General safety instructi ns
IIff aa ggaass lleeaakk iiss ffoouunndd oorr ssuussppeecctteedd,, ttuurrnn ooffff tthhee ggaass ssuuppppllyy aatt tthhee mmeetteerr
aanndd ccoonnttaacctt yyoouurr iinnssttaalllleerr oorr ggaass eemmeerrggeennccyy sseerrvviiccee..
TThheessee iinnssttrruuccttiioonnss sshhoouulldd bbee rreeaadd ccaarreeffuullllyy aanndd rreettaaiinneedd ffoorr ffuuttuurree
rreeffeerreennccee..
DDoo nnoott uussee tthhee ffiirree wwiitthh aa bbrrookkeenn oorr ddaammaaggeedd ggllaassss..
The fire has a safety device which turns off the gas supply if there is a
build up from flue gasses in the combustion room or a temporary gas
cut-off. WWaaiitt aatt lleeaasstt 55 mmiinnuutteess bbeeffoorree ttuurrnniinngg tthhee aapppplliiaannccee oonn aaggaaiinn..
Contact a qualified installer when the appliance goes off regularly.
The appliance has been designed for heating purposes. This means that
all surfaces, including the glass, can become very warm (over 100
degrees . An exception to this is the lower side of the door and the
control buttons.
Due to the newness of materials, they may give off a slight smell for a
period after initial lighting. This is normal, odours will disperse after a
few hours use.
Do not place curtains, clothing, laundry, furniture or other flammable
materials nearby the appliance. The required minimum distance is
100 cm.
Switch off the receiver of the remote control if you don’t use the fire for
a long time. Do not let children use the remote control without
supervision.

UK/IRL
37
UK/IRL
36
Once gas is available at the pilot, continued rotation anti-clockwise
will cause the piezo igniter to spark. This is accompanied by a click
at the valve and should result in the pilot burner igniting.
Once the pilot is lit, the control knob should be held pressed in for
10 seconds. In this time the pilot flame will have heated the flame
supervision thermocouple sufficiently to operate a hold-on magnet
within the valve.
Now turn the control knob A to the position. This allows gas to
enter control knob B.
Kn b B
The {is the OFF position preventing gas entering the main burner if
the pilot is lit.
The knob should be turned slowly anticlockwise. This allows gas to
enter the burner and be ignited by the pilot flame. Once ignition has
taken place, the fire may be set to any level between min. and max. by
adjusting the control knob B.
10.2 T light
1. Push in and turn the control knob (A from {anticlockwise to
the setting (small flame . You will hear a ignition click. Check
that the pilot is lit (if not repeat .
2. Continue to hold in the control knob for a further ten seconds to
ensure that the pilot flame is stable.
3. Release the knob. The pilot should remain alight.
4. Turn the control knob A to the position.
5. Turn knob B slowly anticlockwise, the fire should then ignite.
6. Adjust flames to the required level.
10. CONTROLLING THE APPLIANCE
10.1 Lighting the fire
If the main burner or pilot light are extinguished for any reason, ddoo
nnoott aatttteemmpptt ttoo rreelliigghhtt tthhee ppiilloott wwiitthhiinn 55 mmiinnuutteess..Contact a qualified
installer when the appliance goes off regularly.
The gas valve is behind the ashtray door, open by pulling down.
With control button A you can light the pilot. With the control button
B you can adjust the height of the flames (see fig. 15 .
Kn b A
The {is the OFF position preventing any gas from passing through the
control valve to either the pilot burner or to the main burner. By
pressing the knob in it is possible to turn it anticlockwise. The first
function is to turn on the gas to the pilot- this occurs just before
reaching the |position (if the fire has not been lit for some time it may
be necessary to hold the knob in this position for some seconds to
clear the air from the pipe and allow gas to reach the pilot burner .
fig. 15 gas valve
AB