Faber CAS500 User manual



Page 1of 39
Contents
CAS500 – STARTUP.................................................................................................................................. 2
CONNECT BLUETOOTH RECEIVER........................................................................................................ 2
CONNECT REMOTE CONTROL ............................................................................................................. 4
CAS500 – RECONNECTING REMOTE CONTROL....................................................................................... 5
CAS500 – OPERATION ............................................................................................................................. 7
CAS500 – FLAME ADJUSTMENT .............................................................................................................. 8
CAS500 – SOUND ADJUSTMENT.............................................................................................................. 9
CAS500 – LOW WATER .......................................................................................................................... 10
CAS500 – OVERFLOW DETECTION......................................................................................................... 11
CAS500 – TEST MODE............................................................................................................................ 12
CAS500 – REMOVING FUELBED............................................................................................................. 17
CAS1000 – CONTROLS IDENTIFICATION................................................................................................ 18
CAS1000 – STARTUP.............................................................................................................................. 19
CONNECT BLUETOOTH RECEIVER...................................................................................................... 19
CONNECT REMOTE CONTROL ........................................................................................................... 21
CAS1000 – RECONNECTING REMOTE CONTROL................................................................................... 22
CAS1000 - OPERATION .......................................................................................................................... 24
CAS1000 – FLAME ADJUSTMENT .......................................................................................................... 25
CAS1000 – SOUND ADJUSTMENT.......................................................................................................... 26
CAS1000 – LOW WATER ........................................................................................................................ 27
CAS1000 – OVERFLOW DETECTION....................................................................................................... 28
CAS1000 – TEST MODE.......................................................................................................................... 29
MASTER SIDE ..................................................................................................................................... 29
CAS1000 – TEST MODE.......................................................................................................................... 34
SLAVE SIDE......................................................................................................................................... 34
CAS1000 – REMOVING FUELBEDS......................................................................................................... 39

Page 2of 39
CAS500 – STARTUP
CONNECT BLUETOOTH RECEIVER
Fig. A
CAS500 is connected to
mains power
Press switch on (I)
CAS500 is now in
standby mode
1 Beep
Remove Fuelbed from
product
Connect the Bluetooth
Receiver to the
product via the jack
indicated in Fig. A
Ensure the jack is
connected properly.
See Fig. B.
The Receiver has a
Red LED operating
when it is connected
to the product
correctly
Fig. B
O
I
Bluetooth
Receiver
IMPORTANT:
Product will not
function correctly
without Bluetooth
Receiver connected

Page 3of 39
CAS500 – STARTUP … continued
CONNECT BLUETOOTH RECEIVER
Press On/Standby
button on the
Bluetooth Receiver to
ensure it is connected
and operating
correctly
On board controls
Bluetooth Receiver
Remote control
1 beep
LED light switch on
Element starts to
heat up
After 45 seconds, the
flame effect starts
Place the Fuelbed back on
product
Bluetooth Receiver is connected
and operating correctly
Continue to next page
If you do not want product to be
paired with Remote Control
lb d
If you want product to be paired
with Remote Control
Product will operate correctly
with Bluetooth Receiver

Page 4of 39
CAS500 – STARTUP … continued
CONNECT REMOTE CONTROL
LEDs blink and Beep is heard when
LEDs alternate from ON/OFF
Press On/Standby button on the
Remote Control in order to
synchronise with product
Press the Bluetooth Button on the
On board controls
1 Beep
On board controls
Bluetooth Receiver
Remote control
On board controls
Bluetooth
Receiver
Remote control
B
LEDs blink five times and Beep is
heard five times
The Remote Control is now paired
with product
etime

Page 5of 39
CAS500 – RECONNECTING REMOTE CONTROL
CAS500 is connected to
mains power
Press switch on (I)
CAS500 is now in
standby mode waiting
for an input signal
1 Beep
Press On/Standby
button on the;
On Board controls
or
Bluetooth Receiver
On board controls
Bluetooth Receiver
Remote control
1 beep
LED light switch on
Element starts to heat
up
After 45 seconds, the
flame effect starts
00 i
1b
O
I
IMPORTANT:
Bluetooth Receiver
must be connected
correctly before
pairing the remote
control. See pages
2 and 3.
Remove fuelbed from
product

Page 6of 39
CAS500 – RECONNECTING REMOTE CONTROL … continued
LEDs blink and Beep is heard when
LEDs alternate from ON/OFF
Press On/Standby button on the
Remote Control in order to
synchronise with product
Press the Bluetooth Button on the
On board controls
1 Beep
On board controls
Bluetooth Receiver
Remote control
On board controls
Bluetooth
Receiver
Remote control
B
LEDs blink five times and Beep is
heard five times
The Remote Control is now paired
with product
etime

Page 7of 39
CAS500 – OPERATION
CAS500 is connected to
mains power and water
is supplied
O
I
Press switch
on (I)
CAS500 is
now in
standby
mode
1 Beep
Press On/Standby
button on the;
On Board controls,
Receiver or
Remote Control
CAS500 is
switched off
Press switch
off (O)
On board controls
Bluetooth Receiver
Remote control
1 beep
LED light switch on
Element starts to heat
up
After 45 seconds, the
flame effect starts
Product Turns off
LED's blink
The CAS500 is operating
normally
The CAS500 reads 'Water
Error'. Turn the product
off. See page 10 and 11
for further details
A
S5
00

Page 8of 39
CAS500 – FLAME ADJUSTMENT
The CAS500 is operating normally
Press Flame Down button on the;
On Board controls, Receiver or
Remote Control to reduce the level
of the Flame Effect.
Ob d
Bl t th
Rt
On board controls
Bluetooth Receiver
Remote control
The flames reduce and when
repeatedly press this button you
reach minimum you will hear a
beep. Allow 1 second between
each button press
Press Flame Up button on the; On
Board controls, Receiver or Remote
Control to increase the level of the
Flame Effect.
On board controls
Bluetooth
Receiver
Remote control
The flames increase and when you
repeatedly press this button you
reach maximum you will hear a
beep. Allow 1 second between
each button press
Press Flame Down b
u
b
t
t
t
h
O
ed
uce

Page 9of 39
CAS500 – SOUND ADJUSTMENT
The CAS500 is operating normally
Press Sound Down button on the; On Board
controls only to reduce the fire sound
Pre
ss Sound Up button on the; On Board
controls only to increase the fire sound
On board controls
Bluetooth
Receiver
Remote control
The sound reduces and when you
repeatedly press this button the sound will
reduce until you cannot hear it any more.
Allow 1 second between each button press
The sound increase and when you
repeatedly press this button you reach
maximum you will hear a beep. Allow 1
second between each button press
On board controls
Bluetooth
Receiver
Remote control
Press Sound button on the Receiver or
Remote to turn on and off the fire sound
On board controls
Bluetooth Receiver
Remote control
t

Page 10 of 39
CAS500 – LOW WATER
The CAS500 is switched on and was operating normally
The flame effect stops, you hear a beep and
the LED's CONTINUOUSLY BLINK TWICE
The product has run out of water
Lift off the Fuelbed and set aside
Press the switch to the (0) off position
Product is connected to mains water supply Product uses the bottle to fill the sump
Lift off the Nozzle and lift out the sump
Check that the ball valve is in the open position
and check that there is no leak on the internal
water tubes
Check the mains water supply
Re-establish water to the product and
reassemble the sump and nozzle
Lift out the bottle and take it to your water
supply (kitchen / bathroom)
Fill the bottle and place it back onto the sump
You will see the water flow into the sump
Press the switch to the (I) on position
You will hear one beep
Replace the fuelbed
Press On/Standby button on the;
On Board controls,
Bluetooth Receiver or
Remote Control
Ob d
Bluetooth
Receiver
Remote control
On board controls
ops y
ha
s
ru
n
e
lb
ed
d
l
htoth
ndby b
O
I
O
I
O
I
O
I
Product is operating
normally

Page 11 of 39
CAS500 – OVERFLOW DETECTION
The CAS500 is switched on and was operating normally
The Flame Effect stops, you hear a beep and the
LED's
BLINK ONCE EVERY 8 SECONDS
The product detected an overflow of water
Lift off the Fuelbed and set aside
Press the switch to the (0) off position
Product is connected to mains water supply
Product uses the bottle to fill the sump
Lift off the Nozzle and lift out the sump
Check to see if in the off state water still comes through
the solenoid.
Possibly some grit has become lodged in the solenoid
valve. Using the test mode procedure, switch on the
solenoids to flush water through. If this does not fix the
problem then request a spare solenoid valve
Once the solenoid is replaced or flushed through re
-
establish water to the product and reassemble the
sump
and nozzle
. Remove overflow of water in the sump to
return it to operating water level.
Lift out the bottle. Check that the bottle lid is intact. If
there is a problem with the lid then request a spare lid.
Fill the bottle with the newly fitted lid with water and
place it back onto the sump. Remove overflow of water in
the sump to return it t
o operating water level.
Press the switch to the (I) on position
You will hear one beep, Replace the fuelbed
Press On/Standby button on the;
On Board controls, Receiver or Remote Control
Ob d
Bluetooth
Receiver
Remote control
syou
an ove
uelbed
h to the
ndby b
On board controls
O
I
O
I
O
I
O
I
Product is operating
normally

Page 12 of 39
CAS500 – TEST MODE
On board controls
Bluetooth Receiver
Remote control
CAS500 is connected to
mains power and water
is supplied
O
I
Press switch on (I)
CAS500 is now in
standby mode
1 Beep
Press the Test Mode
button on the
On Board controls
CAS500 is now in
Test Mode
1 Beep
00 is n
To exit Test Mode at any
time, press switch off (O)
and switch on (I)
CAS500 is in standby mode
1 Beep
Remove Fuelbed and
set aside
IMPORTANT:
Test Mode has been integrated into this product to improve end
-of-
line testing during
production and can be used by service Engineers to isolate components for individual
function testing. Test mode should be conducted by trained personnel only. The icons
on
the On Board Control buttons do not match the commands they are associated with, when
in test mode.

Page 13 of 39
CAS500 – TEST MODE … continued
Press Sound Down button on the On Board
controls
Press Sound Up button on the On Board
controls
On board controls
Bluetooth
Receiver
Remote control
On board controls
Bluetooth
Receiver
Remote control
CAS500 is in
Test Mode
This button will turn
the LEDs on or off
during test mode
This button will turn
the sound on or off
during test mode

Page 14 of 39
CAS500 – TEST MODE … continued
Press Flame Down button on the On Board
controls
Press Flame Up button on the On Board
controls
CAS500 is in
Test Mode
This button turns the
fan on or off during test
mode
This button turns the
transducer on or off
during test mode
On board controls
Bluetooth Receiver
Remote control
On board controls
Bluetooth Receiver
Remote control

Page 15 of 39
CAS500 – TEST MODE … continued
Press Bluetooth button on the On Board
controls
Press Test Mode button on the On Board
controls
On board controls
Bluetooth
Receiver
Remote control
CAS500 is in
Test Mode
This button turns the
solenoids on or off
during test mode
This button turns the
element on or off
during test mode (you
may hear the relay
click)
On board controls
Bluetooth Receiver
Remote control

Page 16 of 39
CAS500 – TEST MODE … continued
Press the On/Standby button on the On
Board controls
CAS500 is in
Test Mode
This button turns the
Fuelbed LEDs on or off
during test mode
On board controls
Bluetooth Receiver
Remote control
Note: When in Test Mode, the CAS500 will revert to standby mode if there are
no buttons pressed after a period of 16 seconds. Any parts that may have been
switched on during testing will also switch off.
To exit Test Mode,
Press switch off (O)
O
I

Page 17 of 39
CAS500 – REMOVING FUELBED
The CAS500 is switched on and was operating
normally
LEDs on Fuelbed are operating
Remove the unattached log which houses
the LED connection to the jack. See part 1 in
Fig. C
Lift off the Fuelbed as shown in Fig. D and
set aside
Important:
If the product is left switched
on, be aware the heated element and the lit
LEDs are both exposed to the user.
t
ac
hed
Unplug the jack from the product, see part 2
Fig. C
Fig. C
1
2
Fig. D
Lift off the Metalbed as shown in Fig. E and
set aside
e
d
as
s
Fig. E
Power off the product unless you are
connecting to the remote control or
entering test mode.
Press the standby button on the Bluetooth
receiver, the Remote Control, or switch off
the product at the wall
Product now has Fuelbed removed
On board controls
Bluetooth Receiver
Remote control

Page 18 of 39
CAS1000 – CONTROLS IDENTIFICATION
The CAS1000 has two sides;
Master Side: which commands the overall operation of the product
Slave Side: which follows the operation commands from the Master side
Both sides have independent Flame Effect and Sound controls
CAS1000 ON BOARD CONTROLS
xThe Bluetooth Receiver is connected to the Master side via a jack. See page 19 and 20.
xThe On Board Controls are different for either side.
The Master side has the seven buttons as seen in CAS500 product.
The Slave side also has seven buttons; however, the first two buttons contain no icons, and
these should only be during test mode by trained personnel. For more details, see from
page 29.
CAS1000 BLUETOOTH RECEIVER
CAS1000 REMOTE CONTROL
On board controls (Slave Side)
On board controls (Master Side)
Flame Controls (Master Side)
Flame Controls (Slave Side)
F
l
Fl
a
Flame Controls (Master Side)
Flame Controls (Slave Side)
F
F
l
The CAS1000 bluetooth receiver contains six
buttons, in contrast to the four button
receiver used in the CAS500. The additional
two buttons control the flame effect on the
slave side of the product. See pages 1
9
and
20
for more details.
The CAS1000 Remote Control also contains
six buttons. Similar to the CAS1000 Bluetooth
Receiver, the additional two buttons control
the flame effect on the slave side of the
product. See pages 2
2 and 23
for more
details.

Page 19 of 39
CAS1000 – STARTUP
CONNECT BLUETOOTH RECEIVER
Fig. F
CAS10
00 is connected
to mains power
Press switch on (I)
CAS1000 is now in
standby mode and
waiting for an input
signal
1 Beep
Remove Fuelbed from
product
Connect the Bluetooth
Receiver to the
product via the jack
indicated in Fig. F
1 Beep
Ensure the jack is
connected properly.
See Fig. G.
The Receiver has a
Red LED operating
when it is connected
to the product
correctly
Fig. G
00
0
is
O
I
Bluetooth
Receiver
IMPORTANT:
Product will not
function correctly
without Bluetooth
Receiver connected