Faber BREVA PRO BREV308SS600 User manual

BREV308SS600
BREV368SS600
BREV48SS1200
Installation Instructions
Use and Care Information
Instructions d'installation
Utilisez et d'entretien
Instrucciones de instalación
Información de uso y cuidado
BREVA PRO

2
CONTENTS
Section Page
Important safety instructions
3
Range hood dimensions
6
Installation height requirements
7
Parts
8
Tools needed
10
Attach the Motor
11
Venting method
13
Mount the Motor into the hood
14
Recirculation instructions
18
Connect the Motor cable
19
Mounting on the wall
20
Installation for Mounting Under the Cabinet
24
Connecting house power
27
Operating the controls
28
CFM adjustment < 295CFM
30
CFM adjustment < 395CFM
31
Faber cloud app
32
Remote control
33
Cleaning stainless steel
33
Caring for filters
34
Replacing the activated charcoal filter
35
Replacing bulbs
35
Wiring diagram
36
Warranty
37

3
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START
INSTALLING THIS Range Hood
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a) Never leave surface units unattended at high settings. Boilovers cause smoking and greasy
spillovers that may ignite. Heat oils slowly on low or medium setting.
b) Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes
Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or
filter.
d) Use proper pan size. Always use cookware appropriate for the size of the surface element.
WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE
TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
a) SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the
burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately
EVACUATE AND CALL THE FIRE DEPARTMENT.
b) NEVER PICK UP A FLAMING PAN - You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will
result.
d) Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate
it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit.
* Based on "Kitchen Firesafety Tips" published by NFPA
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this fan with
any solid-state speed control device.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have any questions,
contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at service panel and lock the service
disconnecting means to prevent power from being switched on accidentally. When the
service disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or Explosive
Materials and Vapors.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
1. Installation Work And Electrical Wiring Must Be Done By Qualified Person(s) In Accor-
dance With All Applicable Codes And Standards, Including Fire-Rated Construction.
2. Sufficient air is needed for proper combustion and exhausting of gases through the
flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating
equipment manufacturer's guideline and safety standards such as those published by
the National Fire Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

4
ALL WALL AND FLOOR OPENINGS WHERE THE Range Hood IS INSTALLED MUST
BE SEALED.
This Range Hood requires at least 24" of clearance between the bottom of the Range Hood
and the cooking surface or countertop. This hood has been approved by UL at this distance
from the cooktop.
This minimum clearance may be higher depending on local building codes. For gas cooktops
and combination ranges, a minimum of 30" is recommended and may be required.
Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking
surface or countertop. Consult the cooktop or range installation instructions given by the
manufacturer before making any cutouts.
MOBILE HOME INSTALLATION The installation of this Range Hood must conform to the
Manufactured Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly
Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See
Electrical Requirements"
• Venting system MUST terminate outside the home.
• DO NOT terminate the ductwork in an attic or other enclosed space.
• DO NOT use 4" laundry-type wall caps.
• Flexible-type ductwork is not recommended.
• DO NOT obstruct the flow of combustion and ventilation air.
• Failure to follow venting requirements may result in a fire.
WARNING
!
!
!
!
VENTING REQUIREMENTS
Determine which venting method is best for your application. Ductwork can extend either
through the wall or the roof.
The length of the ductwork and the number of elbows should be kept to a minimum to pro-
vide efficient performance. The size of the ductwork should be uniform. Do not install two
elbows together. Use duct tape to seal all joints in the ductwork system. Use caulking to seal
exterior wall or floor opening around the cap.
Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air
turbulence that greatly reduces performance.
Make sure there is proper clearance within the wall or floor for exhaust duct before making
cutouts. Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut,
then a supporting frame must be constructed.
WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.
CAUTION - To reduce risk of fire and to properly exhaust air, be sure to duct air outside
– Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces,
or garages.
Cold Weather installations
An additional back draft damper should be installed to minimize backward cold air flow and a nonmetallic
thermal break should be installed to minimize conduction of outside temperatures as part of the vent
system. The damper should be on the cold air side of the thermal break. The break should be as close
as possible to where the vent system enters the heated portion of the house.
3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hidden utilities.
4. Ducted fans must always be vented to the outdoors.

5
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A
time-delay fuse or circuit breaker is recommended. The fuse must be sized per local codes
in accordance with the electrical rating of this unit as specified on the serial/rating plate
located inside the unit near the field wiring compartment.
• Electrical ground is required on this Range Hood.
• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other
materials, DO NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral
or grounding circuit could result in electrical shock.
• Check with a qualified electrician if you are in doubt as to whether the Range
Hood is properly grounded.
• Failure to follow electrical requirements may result in a fire.
WARNING
!
!
!
!

6
RANGE HOOD DIMENSIONS
BREVA30
30"

7
BREVA36
36"

8
BREVA48
48"

9
INSTALLATION HEIGHT REQUIREMENTS
MIN. 24" OVER ELECTRIC / MIN. 30" OVER GAS
Min.24" Min.30"
TOOLS NEEDED
TOOL
Tape Measure
Pencil
Electric Drill with 5/16" Drill Bit
Phillips Screwdriver
Metal sheers
Work gloves

10
REF. PART QTY
AHood body 1
BGrease rails 2
CGrease filters 2
EDamper 1
FSpacer 1
XMotor 1
REF PART
GPozi Screws (1/8" x 3/8") 5
HPozi Screws (3/16" x 1/8") 4
IPozi Screws (Screws 3/16" x 1 15/16") 4
LPozi Screws (Screws 3/16" x 1 3/4") 4
NWall bracket 2
MCap 1
PARTS INCLUDED
BREVA 30
PARTS
PARTS NEEDED
PART
8" Round Metal Ductwork
Foil tape

11
ACCESSORIES AVAILABLE
ACCESSORY SKU#
TELESCOPIC PRO CHIMNEY 30 TELEPRO30
TELESCOPIC BACKSPLASH 30 BACK 30
DUCTLESS KIT 30 DUCTGRT304
CHARCOAL FILTER FILTER6
FIXED WIRING BOX WIREBOX2
REMOTE CONTROL REMCTRL2
X
A
E
F
Z
B
C

12
PARTS
REF. PART QTY
AHood body 1
BGrease rails 2
CGrease filters 3
EDamper 1
FDucting plate 1
XMotor 1
REF PART
GPozi Screws (1/8" x 3/8") 4
HPozi Screws (3/16" x 1/8") 4
IPozi Screws (Screws 3/16" x 1 15/16") 4
LPozi Screws (Screws 3/16" x 1 3/4") 4
NWall bracket 2
PARTS NEEDED
PART
8" Round Metal Ductwork
Foil tape
BREVA 36
PARTS INCLUDED

13
X
A
E
F
Z
B
C
ACCESSORIES AVAILABLE
ACCESSORY SKU#
TELESCOPIC PRO CHIMNEY 36 TELEPRO36
TELESCOPIC BACKSPLASH 36 BACK 36
DUCTLESS KIT 36 DUCTGRT364
CHARCOAL FILTER FILTER6
FIXED WIRING BOX WIREBOX2
REMOTE CONTROL REMCTRL2
SECOND Motor KIT IB600PR
IMPORTANT: With the second motor kit #IB600PR the recirculating installations is not possible..

14
PARTS
BREVA 48
PARTS INCLUDED
REF. PART QTY
AHood body 1
BGrease rails 2
CGrease filters 4
EDamper 1
FDucting plate 1
XMotor 2
REF PART
GPozi Screws (1/8" x 3/8") 4
HPozi Screws (3/16" x 1/8") 4
IPozi Screws (Screws 3/16" x 1 15/16") 4
LPozi Screws (Screws 3/16" x 1 3/4") 4
NWall bracket 2
PARTS NEEDED
PART
10" Round Metal Ductwork
Foil tape

15
ACCESSORIES AVAILABLE
ACCESSORY SKU#
TELESCOPIC PRO CHIMNEY 48 TELEPRO48
TELESCOPIC BACKSPLASH 48 BACK 48
FIXED WIRING BOX WIREBOX2
REMOTE CONTROL REMCTRL2
X
A
E
Z
B
C

16
ATTACH THE MOTOR
1Remove the 4 screws inside the hood on the Motor support panel.
2Remove the Motor support panel.
BREVA 30

17
3Attach the Motor Xonto the support panel with the 4 screws Has shown.
IMPORTANT: Please note the direction of the motor in the drawing.
H
X

18
ATTACH THE MOTOR
1
2
Remove the 2 screws inside the hood on the Motor support panel. Slide the metal
clips to the left and right to unlock the Motor support as shown below.
Remove the Motor support panel by sliding the panel down and towards you
away from the brackets.
BREVA 36

19
3Attach the Motor Xonto the support panel with the 4 screws Has shown.
IMPORTANT: Please note the direction of the motor in the drawing.
X
H

20
ATTACH THE MOTOR
1
2
Remove the 2 screws inside the hood on the Motor support panel. Slide the metal
clips to the left and right to unlock the Motor support as shown below.
Remove the Motor support panel by sliding the panel down and towards you
away from the brackets.
BREVA 48