Faber CHLOE CHLO36BK600 User manual

CHLO28GR600
CHLO28BK600
CHLO36BK600
Installation Instructions
Use and Care Information
Instructions d'installation
Utilisez et d'entretien
Instrucciones de instalación
Información de uso y cuidado
CHLOE'

2
READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START
INSTALLING THIS RANGEHOOD
WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
a)Never leave surface units unattended at high settings. Boilovers cause smoking and
greasy spillovers that may ignite. Heat oils slowly on low or medium setting.
A KV@XRSTQMGNNC.-VGDMBNNJHMF@SGHFGGD@SNQVGDMl@LADHMFENNCHD"QDODR
Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
c)Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan
NQkKSDQ
d)Useproperpansize. Alwaysusecookwareappropriateforthesizeofthesurfaceelement.
WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A
RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
@2,.3'$1%+ ,$2VHSG@BKNRDkSSHMFKHCBNNJHDRGDDSNQLDS@KSQ@XSGDMSTQMNEESGDATQMDQ
!$" 1$%4+3./1$5$-3!41-2(ESGDl@LDRCNMNSFNNTSHLLDCH@SDKX$5 "4 3$
AND CALL THE FIRE DEPARTMENT.
b)NEVER PICK UP A FLAMING PAN - You may be burned.
c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will
result.
d)Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
 3GDkQDHRRL@KK@MCBNMS@HMDCHMSGD@QD@VGDQDHSRS@QSDC
 3GDkQDCDO@QSLDMSHRADHMFB@KKDC
 8NTB@MkFGSSGDkQDVHSGXNTQA@BJSN@MDWHS
* Based on "Kitchen Firesafety Tips" published by NFPA
WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this
fan with any solid-state speed control device.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer. If you have any
questions, contact the manufacturer.
2. Before servicing or cleaning unit, switch power off at service panel and lock the
service disconnecting means to prevent power from being switched on acciden-
tally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or
Explosive Materials and Vapors.
WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING:
1. (MRS@KK@SHNM6NQJ MC$KDBSQHB@K6HQHMF,TRS!D#NMD!X0T@KHkDC/DQRNMR(M BBNQ-
dance With All Applicable Codes And Standards, Including Fire-Rated Construction.
2. 2TEkBHDMS@HQHRMDDCDCENQOQNODQBNLATRSHNM@MCDWG@TRSHMFNEF@RDRSGQNTFG
SGDlTDBGHLMDXNEETDKATQMHMFDPTHOLDMSSNOQDUDMSA@BJCQ@ESHMF%NKKNVSGD
heating equipment manufacturer's guideline and safety standards such as those
OTAKHRGDCAXSGD -@SHNM@K%HQD/QNSDBSHNM RRNBH@SHNM -%/ @MC SGD LDQHB@M
2NBHDSXENQ'D@SHMF1DEQHFDQ@SHNM@MC HQ"NMCHSHNMHMF$MFHMDDQR 2'1 $@MC
the local code authorities.

3
ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST
BE SEALED.
This rangehood requires at least 24" of clearance between the bottom of the rangehood
and the cooking surface or countertop. This hood has been approved by UL at this distance from
the cooktop.
This minimum clearance may be higher depending on local building codes. For gas cooktops and
combination ranges, a minimum of 30" is recommended and may be required.
Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface
or countertop. Consult the cooktop or range installation instructions given by the manufacturer
before making any cutouts.
MOBILEHOMEINSTALLATIONThe installationof thisrangehood mustconform tothe Manufactured
Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard
for Mobile Home Construction and Safety, Title 24, HUD, Part 280). See Electrical Requirements.
• Venting system MUST terminate outside the home.
• DO NOT terminate the ductwork in an attic or other enclosed space.
• DO NOT use 4" laundry-type wall caps.
• Flexible-type ductwork is not recommended.
• DO NOTNARSQTBSSGDkNVNEBNLATRSHNM@MCUDMSHK@SHNM@HQ
q%@HKTQDSNENKKNVUDMSHMFQDPTHQDLDMSRL@XQDRTKSHM@jQD
WARNING
!
VENTING REQUIREMENTS
Determine which venting method is best for your application. Ductwork can extend either through the
wall or the roof.
3GDKDMFSGNESGDCTBSVNQJ@MCSGDMTLADQNEDKANVRRGNTKCADJDOSSN@LHMHLTLSNOQNUHCDDEjBHDMS
performance. The size of the ductwork should be uniform. Do not install two elbows together. Use
CTBSS@ODSNRD@K@KKINHMSRHMSGDCTBSVNQJRXRSDL4RDB@TKJHMFSNRD@KDWSDQHNQV@KKNQkNNQNODMHMF
around the cap.
Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air
turbulence that greatly reduces performance.
,@JDRTQDSGDQDHROQNODQBKD@Q@MBDVHSGHMSGDV@KKNQkNNQENQDWG@TRSCTBSADENQDL@JHMFBTSNTSR
Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting
frame must be constructed.
WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.
" 43(.-3NQDCTBDQHRJNEkQD@MCSNOQNODQKXDWG@TRS@HQADRTQDSNCTBS@HQNTSRHCDm#N
notventexhaustairintospaceswithin wallsorceilingsorintoattics,crawlspaces,orgarages.
3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities.
4. Ducted fans must always be vented to the outdoors.

4
ELECTRICAL REQUIREMENTS
A 120 volt, 60 Hz AC-only electrical supply is required on a separate 15 amp fused circuit. A time-delay
fuse or circuit breaker is recommended. The fuse must be sized per local codes in accordance with
SGDDKDBSQHB@KQ@SHMFNESGHRTMHS@RRODBHjDCNMSGDRDQH@KQ@SHMFOK@SDKNB@SDCHMRHCDSGDTMHSMD@QSGDjDKC
wiring compartment.
ELECTRICAL INSTALLATION WITH WIRING BOX
THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY. Wire sizes must conform to the
QDPTHQDLDMSRNESGD-@SHNM@K$KDBSQHB@K"NCD -2(-%/ K@SDRSDCHSHNM@MC@KKKNB@KBNCDR@MC
ordinances. Wire size and connections must conform with the rating of the appliance. Copies of the
standard listed above may be obtained from:
National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
This appliance should be connected directly to the fused disconnect (or circuit breaker) through
kDWHAKD@QLNQDCNQMNMLDS@KKHBRGD@SGDCBNOODQB@AKD KKNVRNLDRK@BJHMSGDB@AKDRNSGD
@OOKH@MBDB@MADLNUDCHERDQUHBHMFHRDUDQMDBDRR@QX 4++HRSDCŭBNMCTHSBNMMDBSNQLTRS
be provided at each end of the power supply cable (at the appliance and at the junction box).
6GDML@JHMFSGDDKDBSQHB@KBNMMDBSHNMBTS@ŭGNKDHMSGDV@KK GNKDBTSSGQNTFGVNNC
must be sanded until smooth. A hole through metal must have a grommet.
• Electrical ground is required on this rangehood.
• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO
NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or
grounding circuit could result in electrical shock.
q"GDBJVHSG@PT@KHjDCDKDBSQHBH@MHEXNT@QDHMCNTAS@RSNVGDSGDQSGDQ@MFDGNNCHR
properly grounded.
q%@HKTQDSNENKKNVDKDBSQHB@KQDPTHQDLDMSRL@XQDRTKSHM@jQD
WARNING
2S@SDNE"@KHENQMH@/QNONRHSHNM6@QMHMF42NMKX
WARNING
This product contains chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov

5
RANGEHOOD DIMENSIONS
7-11/16"
7 11/16"
REAR DUCTED VENTING INSTALLATION
SGD'NNCRGNTKCBNLDRDSHMSGHRONRHSHNM
´

6
Min. 24" Min. 30"

7
MAIN PARTS
Components
Ref. Qty. Product Components
1 1 HoodBody,completewith:Con-
trols, Light, Filters, Blower.
2 1 Rear Section
8 1 Recirculation Vent Grill
10 1 Damper ø 5 7/8"
Ref. Qty. Installation Components
12a 4 Screws 1/4" x 9/16"
12b 2 Screws 1/8"x3/8" (for Wiring Box
mounting)
12e 2 Screws 1/8"x3/8" (for Recirculation
Vent Grill mounting)
Qty. Documentation
1 Instruction Manual
10
1
12a
2

H
12b
Available Accessories
Recirculation Vent Kit - Activated Charcoal Filter - sku# FILTER1
Washable Long Lasting Charcoal Filter Kit - sku# FILTER1LL
Telescopic Chimney Accessory Kit - Upper and Lower Chimney Flue for Ducted or Recirculation Venting -
sku#CHIMCHBK - Black
Wireless Remote Control Accessory - REMCTRL2
Cfm reducer kit (600-400) - sk# CFMRED-2
Cfm reducer kit (600-300) - sku# CFMRED
Parts needed
- 6" Round Metal ductwork .

8
Choose your ducting method
Non Ducted - Recirculation OptionDucted Venting Options Installation
Requires purchase of Activated Charcoal Accessory
Horizontal
Vertical
6"
When used in recirculation mode, To Reduce the
Risk of Fire and Shock use only conversion kit
Model FILTER1 or FILTER1LL.
Rear
18
Vertical and Horizontal Ducted Venting Installation with the optional Kit Chimney
6"
6"
9 9
Requires purchase of Chimney accessory

9
1
2
Draw a vertical line on the supporting wall as high as practical, at the center of the area in which the hood will be installed.
'UDZDKRUL]RQWDOOLQHDWZKHUHWKHERWWRPHGJHRIWKHKRRGZLOOEHORFDWHGDVLQGLFDWHGLQWKH¿JXUHWKDWLVDPLQLPXP
of 24" above Electric cooking surface and 30" above Gas.
Mark the wall where indicated (A), 11 9/16" above the horizontal line and at 4 5/16" distance on the left and right of vertical
line. Checking that the two marks are level.
Insert two wall plugs and screws (purchased separately) into the (A) holes as shown and leave 1/4" of screws exposed.
Mark the wall where indicated (B), 4 1/4" above the horizontal line and at 4 5/16" distance on the left and right of vertical
line. Checking that the two marks are level.
Insert two wall plugs (purchased separately).
Installation Instructions
Rear Section Installation
´ ´
11 9/16”
4 1/4”
4 5/16” 4 5/16”
$
%
$
%

10
3
Hook the Rear Section as shown in the image above
onto the upper screws and fully secure.
From inside fully secure the two lower screws (purchased
separately).
4
L
2x
L
2x
5
Open the panel, unlock the security cable as
VKRZQ5HPRYHWKH¿OWHUVE\SXVKLQJWKHOHYHU
towards the back of the unit and at the same
time pulling downward. Do not discard the
¿OWHUVDQGVHWDVLGHIRUIXWXUHXVH
For Non-Ducted Recirculation Option
13
Rear Ducting Installation

11
Remove the 4 screws as shown and take off the cover plates.
Do not discard and set aside for future use.
)URPLQVLGHWKHKRRGXVHDÀDWKHDGVFUHZGULYHUDVVKRZQLQ
image above, to disconnect the left and right Connectors from
the blower.
6
Unscrew the 2 screws
(Posi-Drive) that hold
the blower and unlock it
from the initial position as
shown in Image a.
E F
D G
[
[
After removing blower
rotate as shown until it is
in the correct rear venting
position as shown in
Image b-c.
Use the two screws that
were removed to secure
the blower as shown in
Image d.
7
8
P
P1
2x
Fix the Recirculation Vent Grill with two screws.
9
12e

12
A10
Fix the cover plate with the 4 screws removed previously and
route the wiring box outside of the hood body through the notch
on the cover plate.
$WWDFKHDFKFKDUFRDO¿OWHUWRWKHEODFNJULGRQHDFKVLGHRIWKH
EORZHU3UHVVWKHFKDUFRDO¿OWHUWLJKWO\WRWKHEODFNJULGRQWKH
EORZHUVLGHDQGURWDWHWKH¿OWHUFORFNZLVHWRZDUGVWKHIURQW
of the hood) until it locks into place. Turn counterclockwise
(towards the back of the hood) to remove.
Required Activated Charcoal Filter Accessory -
sku # - FILTER1 (purchased separately).
Long Lasting Charcoal Filter Kit - sku#
FILTER1LL
A10
10
11 12
From inside the hood re-connect the Connectors on the left
and right side shown in the image above.

13
13
Break the Hole in the Wiring
Box to connect the Hood to
Power Supply Cable.
Pull the cable from the Power
Supply through the Hole for
the Electrical Connection to
the Wiring Box.
Remove the Wiring Box
compartment cover by
unscrewing the two screws.

14
14
A. Home power supply cable
B. Black wires
C. UL listed wire connectors
D. White wires
E. Green (or bare) ground wire from home power supply connected to green ground screw
F. Range hood power supply cable
G. Green ground wire from Range hood power supply cable connected to green ground screw.
E
A
F
D
C
B
G
Installation of wiring connection
5HPRYHWKHFRYHUIURPWKH¿HOGZLULQJFRPSDUWPHQW
DO NOT turn on the power until installation is complete!
Connect the Power Supply Cable to the rangehood.
Connect the Green (Green and Yellow) ground wire under the Green grounding
screw. Attach the White lead of the power supply to the White lead of the range-
hood with a twist-on type wire connector.
Attach the Black lead of the power supply to the Black lead of the rangehood
with a twist-on type wire connector.
5HSODFHWKH¿HOGZLULQJFRPSDUWPHQWFRYHU

15
15
16
Secure the Wiring Box as shown
in the image with the 2 Screws
(12b). 12b
Attention: After the Wiring Box installation, place the Cable inside a Rear Section without stressing for
the Cable.
12a
Screw the two 12a screws into
the Rear Section with the heads
exposed by 1/4".

16
%HIRUH¿[LQJWKH%RG\+RRGWRWKH
Rear Section, Unscrew the 2 screws
WR¿[WKH%ORZHU
This operation will simplify the connect
of Air outlet duct.
[
Only for the Rear Ducting Installation
Use this dimensional drawing to help with planning of duct
connection.
Install to the Roof or Wall attach ductwork.
After ¿[LQJWKH%RG\+RRGWRWKH5HDU6HFWLRQ¿[
the Blower in the previously position with the
same 2 screws.
[

17
Complete the Securing of the Hood
Body to the Rear Section by installing
the two remaining 12a screws into
the lower holes on the Rear Section.
Secure all the 4 screws.
18
M1 = 4x
M6x15
M1
4x
19
5HSODFHWKH¿OWHUVLQWRWKHKRRGDQGORFNWKH
security cable as shown in the image to the
right. Close the panel.
17
Hook the hood body onto
the upper screws (12a)
of the mounted Rear
Section, and then fully
secure the screws.
L
2x
12a

18
Vertical and Horizontal Ducted Venting Installation with the optional Kit Chimney
Remove the 4 screws as shown and take off the cover plates.
Do not discard and set aside for future use.
)URPLQVLGHWKHKRRGXVHDÀDWKHDGVFUHZGULYHUDV
shown in image above, to disconnect the left and right
Connectors from the blower.
12
3
Open the panel, unlock the security cable as shown.
5HPRYHWKH¿OWHUVE\SXVKLQJWKHOHYHUWRZDUGVWKH
backof theunitandat thesametime pullingdownward.
'RQRWGLVFDUGWKH¿OWHUVDQGVHWDVLGHIRUIXWXUHXVH
Installation with the optional Kit Chimney - Preparation of Hood

19
4
Pull the Cable from
the rear hole.
Fix the Cable in the hole on the Top of the Hood
as show.
Move the Cable from the rear of the
Hood to the Top of the Hood.

20
Re-secure the Cover Plate as shown with the
screws removed previously.
6
5
Unscrew the 2 screws that hold the blower and unlock it from the initial position as shown in Image a.
E F
D G
[
[
After removing blower rotate as shown until it is in the correct rear venting position as shown in Image b-c.
Use the two screws (Posi-Drive) that were removed to secure the blower as shown in Image d.