Falcon 812L User manual

*D-2116*
D-2116
1. PREPARE INSIDE FACE OF DOOR
FOR DEVICE. SEE DEVICE
DIRECTIONS FOR LOCATIONS OF
VERT. AND DEVICE REF. CENTER
LINES.
2. PREPARE OUTSIDE FACE
OF DOOR FOR TRIM:
A. TRANSFER VERT. AND DEVICE
REF. CENTER LINES FROM
INSIDE FACE TO OUTSIDE FACE
OF DOOR. BE SURE VERT.
CENTER LINE IS PARALLEL TO
EDGE OF DOOR.
B. LOCATE AND PREPARE ALL
HOLES AS INDICATED.
3. RE-HAND TRIM IF NECESSARY (SEE
OTHER SIDE).
4. INSTALL TRIM ON DOOR AND CUT
LEVER SPINDLE TO SIZE:
A. TRIM MOUNTING: FOUR STUDS
ARE THRU-BOLTED TO DEVICE
WHEN DEVICE IS INSTALLED.
B. CUT LEVER SPINDLE:
•VERTICAL AND THREE POINT
LATCH: LEVER SPINDLE TO
EXTEND 5/8” TO 3/4” BEYOND
DOOR SKIN.
•MORTISE: LEVER SPINDLE TO
BE INSIDE DOOR SKIN BY 1/4”.
5. ASSEMBLE CYLINDER, IF REQUIRED.
A. IF USING MORTISE CYLINDER,
INSTALL CYLINDER TO MORTISE
LOCK.
B. IF USING RIM CYLINDER, CUT
TAILPIECE TO EXTEND 3/8”
BEYOND INSIDE FACE OF DOOR
(SEE OTHER SIDE).
6. INSTALL DEVICE ON DOOR
PER DEVICE INSTRUCTIONS.
NOTE: DIMENSIONS “A” AND “B” ARE THE SAME FOR L AND ST TRIM REGARDLESS OF FUNCTION.
“A” = 1-3/8” “B”= OMIT “A” = OMIT “B”= OMIT
“A” = 1-3/8” “B”= 1-3/8”
(F-)18-V-L(2O.C.)
“A” = OMIT “B”= 1-3/8”
(F-)18-V-NL x L DT
(F-)18-V-L2
(F-)XX-M-L (F-)XX-V-L (F-)18-M-L (F-)18-V-L
(F-)XX-M-L (NL) (F-)XX-V-L (NL) (F-)18-M-L (NL) (F-)18-V-L (NL)
(F-)XX-M-NL x L DT (F-)18-M-NL x L DT (F-)XX-M-L2 (F-)18-V-L2
(F-)XX-M-L (BE) (F-)18-V-L (BE) (F-)XX-M-L DT (F-)18-V-L DT
(F-)XX-V-L (BE) (F-)18-M-L (BE) (F-)XX-V-L DT (F-)18-M-L DT
LHR SHOWN
RHR OPPOSITE
1-1/4” 1-13/16”
3-7/8”
1/4”
7-3/4”
FOR
HEIGHT
FROM
FINISHED
FLOOR,
REFER TO
DEVICE
TEMPLATE
1-3/4”
7/8”
FOR BACKSET, REFER TO DEVICE TEMPLATE
1/2” DIA., 4 PLACES
METAL DOOR, OUTSIDE
FACE OF DOOR ONLY;
WOOD DOOR, THRU
FOR METAL DOOR ONLY (4 PLACES):
1/4” DIA. INSIDE FACE OF DOOR ONLY
“A” DIA. THRU
“B” DIA. THRU
1-1/4” THRU
DEVICE REF.
C
L
VERT. C
LVERT. C
L
OUTSIDE FACE OF DOOR INSIDE FACE OF DOOR
WOOD DOOR METAL DOOR
(Trim side only for
mortise devices)
Trims for (F)18 and (F)XX Series Surface Vertical Rod, Mortise, and Three Point Latch Devices
812L & 816L
Installation Instructions
© Allegion 2014
Printed in U.S.A.
D-2116 Rev. 01/14-b
Customer Service
1-877-671-7011 www.allegion.com/us

RE-HANDING INSTRUCTIONS FOR L TRIM
(816 TRIM CANNOT BE RE-HANDED)
RHR to LHR conversion shown
LHR to RHR conversion opposite
1. Remove two screws.
2. Remove back plate.
3. Remove set screw, then remove cam.
4. Rotate lever to correct position for
handing required.
5. Re-install cam in reversed
position. “R” on cam faces out for RHR;
“L” on cam faces out for LHR.
6. Push cam in until it stops, then re-install
set screw.
7. Re-install back plate (tab fits into slot).
8. Re-install two screws.
Lever and cam
in RHR position
(“R” on cam faces out)
Lever and cam
in LHR position
(“L” on cam faces out)
Back plate
Cam
Set screw
L
R
Tab fits into slot
RE-HANDING INSTRUCTIONS FOR DT TRIM
(816 TRIM CANNOT BE RE-HANDED)
RHR to LHR conversion shown
LHR to RHR conversion opposite
1. Remove two screws.
2. Remove back plate.
3. Remove bracket.
4. Rotate lever to correct position for
handing required.
5. Re-install bracket.
6. Re-install back plate.
7. Re-install two screws.
Lever in RHR position Lever in LHR position
Back plate
Bracket
RIM CYLINDER INSTALLATION
Tabs on cylinder
mounting bracket
engage slots on trim
Cylinder
mounting
bracket
Cut tailpiece
to extend 3/8”
beyond door
surface