FamilyTool FMT001INF User manual
1 IM-FMT001INF-R0
INSTRUCTION
MANUAL
12v DC Digital Tire Inflator
mod. FMT001INF
Warning!:
following, should always be followed to reduce the risk of fire, personal injury and material
damage.
• Read all of this manual carefully before using the appliance.
•
• Retain this manual for future reference.
•
pressure inflatables and sport balls.
TECHNICAL SPECIFICATION
Voltage: 1 volt DC Max Air Flow: 5.8 g/min
Max Pressure: 150 psi (blocked head pressure) Cable length: 1 ”
Duty Cycle (minutes): 15 ON / 30 OFF
2 IM-FMT001INF-R0
Fig. A Fig. B
8
5
7
Fig. H
Fig. D
Fig. F
9
11
3
2
Fig. E
4
9
6
Fig. C 1
2
1
10
Fig. G
3 IM-FMT001INF-R0
Using your appliance
•
power supply.
• Always take care when using the appliance.
• Never pull the power supply cord to disconnect the plug from the socket. Keep the power
supply cord away from heat, oil and sharp edges.
• If the power supply cord is damaged during use, disconnect the appliance from the power
power supply.
•
parts and before cleaning.
Safety of others
• .
• Do not exceed rated pressure of the item being inflated. Do not overinflate
Aer use
•
• When not in use, the appliance should be stored in a dry place. Children should not have
access to stored appliances.
Inspecon and repairs
•
•
•
• Before use, check the power supply cord for signs of damage, ageing and wear.
•
Electrical Safety
This appliance is powered by low voltage current 1 Volt DC. Always check that the power supply
ers supplied by the manufacturer should be used.
• Do not use the appliance near flammable materials.
•
• Keep your hair, clothing and gloves away from moving parts.
• Do not use damaged accessories.
• Children must be supervised to ensure they do not play with the appliance.
Digital Display Operang Instrucons
-off pressure (Fig. C)
A)
Kpa
B)
When the pressure gauge reach this pre-
4 IM-FMT001INF-R0
Use
Warning!
A) o Inflate ires
1. Screw connector ( ) on air valve stem (fig. E).
. Plug power cord (8) into suitable power point (fig. B)
4. Press on/off switch (6).
5. The inflator will shut-
6. Press on/off switch (6) and unplug power cord from socket.
B) o Inflate ires with Presta valve
1. Screw Presta valve adapter (9) on air valve stem (fig. F).
Screw connector ( ) on Presta valve adapter (9) (fig. F) and follow steps 3 to 6 point A above
1. Insert the connector adapter (8) on the connector ( ) .
. Follow steps to 6 point A above
D) o Inflate sport balls
1. Insert the sport adapter (10) on the connector ( ) .
. Follow steps to 6 point A above
E) o use working and emergency lights
Maintenance
cleaning.
Cleaning
Warning! Before cleaning and maintenance, switch the appliance off and unplug it.
•
• Do not use any abrasive or solvent-based cleaner.
• Do not immerse the appliance in water.
Storage
• Wrap the power supply cord and the pressure hose inside the unit (fig. G).
•
Troubleshoong
A) Inflator will not turn on:
1. Check if the digital gauge is set to a lower pressure than your current reading —> increase
pressure
. Check if the digital display is set to the desired pressure unit
3. Check if the power plug is correctly inserted
4. Check the vehicle power outlet fuse. It should be 15Amps minimum.
5.
fuse (11), and inspect it. —> if needed replace fuse (11) with one of the same amperage
1.
.
C) Air loss when unscrewing the hose:
1. It is normal to have a small air loss when unscrewing the hose. In some bicycle Schrader
valve the spring-
change the Schrader valve.
