Fanimation Bourbon Street FP510 Series User manual

Copyright 2007 Fanimation, Inc. 2007/12
10983 Bennett Parkway
Zionsville, IN 46077
Toll Free [phone]
FAX [phone]
Outside U.S. call [phone]
Visit Our Website www.fanimation.com
The Bourbon Street®Ceiling Fan Assembly
SPECIFICATION SHEET
Product Specifications subject to change
The Bourbon Street®
FP510 / FP520 / FP540 / FP550 / FP580
MOTOR SPECS:
120 VAC, 1.8 amps, single-speed, ceiling mounted, reversible. 220 VAC, 50 Hz, single-speed motor also available.
No more than 6 fan assemblies or idlers combined per motor. Not recommended for sound-sensitive areas.
FAN SPEED:
Single-speed, approximately 90 rpm with reversing switch (located on switch cup housing).
UNIT SPACING:
6 ft. to 16 ft., although system configuration may affect the maximum spacing.
USE OF IDLERS:
Idler assemblies are utilized for the following circumstances:
1) When fan centers exceed 16 ft. (greater than 16 ft. may cause excessive belt sagging).
2) When obstacles prevent direct belting between two fan units.
PULLEY CONFIGURATION:
System layout will determine number of pulleys each assembly will have. A typical fan assembly will have two pulleys
located just below the fan base. In this configuration the pulley will have an adjustment range of approximately 2”
allowing for small changes in ceiling elevation.
BELTING:
Belting material provided with each system consist of 1/16” thick, 1-1/8” wide, 40’ long 3-ply brown neoprene (belts
are wrapped around the appropriate pulleys and pulled tight enough to remove slack and fastened with the pop rivet
kit provided with system, excess belt is then cut). Belting will stretch some with time and use, and may have to be
retightened at a later date.
INSTALLATION HARDWARE:
Each system comes complete with all hardware necessary for complete installation with the exception of the plywood
mounting platforms or backing (mounting platforms or backing to be provided by owner or contractor). Lag bolts are
included with the system for anchoring assemblies to mounting platforms or directly to walls with 3/4” backing previously
installed.
OPTIONAL BLADE SETS:
Blade sets consist of 5 blades, though mounting only four is an option and will increase speed and airflow. See Catalog
or visit our website, www.fanimation.com for more blade selections.
DAMP LOCATION:
Fan and Motor assemblies are not rated for Damp Location usage.

**Available Finish (codes)
AB Antique Brass
BL Black
Ordering Information (Items Sold Seperately)
Item Catalog No. Description
Fan Unit Assembly FP510**
FP520**
Short Pulley Assembly
Long Pulley Assembly
Motor Unit
Assembly FP580** Single-speed, reversible
Blades (Set of 5) FP1018 Reversible Oak/Walnut
12º Blade Pitch
Idler FP540**
FP550**
Wall Mount
Ceiling Mount
220V Model (Export version)
Motor Unit Assembly – 220 volt, 50 Hz
Single-speed, reversible
Finishes: available in 2 standard finishes
All dimensions shown in inches
Belt dimensions are same as long fan assembly
**Insert Finish Codes
Motor Unit Assembly – FP580**
Weight 26 lbs
Ceiling Projection 9˝
Base Dimension 8˝x 15½˝
Max. Fan / Idler Units (combined per Motor) 6
MOUNTING REQUIREMENTS
18˝x 18˝x ¾˝plywood backing able to support at least 50 lbs.
Flush mounted junction box placed on center.
ELECTRICAL REQUIREMENTS
A 120 Volts AC, 60 Hz, 15 amps circuit electrical feed, centered
under the motor unit and wired to a standard wall switch (user
supplied) is required. The motor unit will not operate more
than 6 fan assemblies or idlers combined.
Long Fan Assembly – FP520**
Weight (basic Fan Unit only) 48 lbs
Ceiling Projection (w/o light kit) 36˝
Blade Sweep (with FP1018 blades) 52˝
Base Diameter (3-Hole Pattern Diameter) 16¾˝(13˝)
MOUNTING REQUIREMENTS
18˝x 18˝x ¾˝plywood backing able to support at least
100 lbs. Three 5/16˝lag bolts are used to secure the fan
base to the plywood backing. Flush mounted junction box
placed on center (for light kit).
Short Fan Assembly – FP510**
Weight (basic Fan Unit only) 38 lbs
Ceiling Projection (w/o light kit) 21˝
Blade Sweep (with FP1018 blades) 52˝
Base Diameter (3-Hole Pattern Diameter) 16¾˝(13˝)
MOUNTING REQUIREMENTS
18˝x 18˝x ¾˝plywood backing able to support at least
100 lbs. Three 5/16˝lag bolts are used to secure the fan
base to the plywood backing. Flush mounted junction box
placed on center (for light kit).
Idler / Wall Mount – FP540**
Weight 20 lbs
Wall Projection 14½˝
Base Dimension 14¾˝x 8˝
MOUNTING REQUIREMENTS
18˝x 18˝x ¾˝plywood backing able to support at least 50
lbs. Four 5/16˝lag bolts are used to secure the idler base
to the plywood backing.
NOTE: Not required for most installations.
Idler / Ceiling Mount – FP550**
Weight 15 lbs
Ceiling Projection 12˝
Base Diameter (3-Hole Pattern Diameter) 16¾˝(13˝)
MOUNTING REQUIREMENTS
18˝x 18˝x ¾˝plywood backing able to support at least 50
lbs. Three 5/16˝lag bolts are used to secure the idler base
to the plywood backing.
NOTE: Not required for most installations.
9½˝distance
between belts
3˝between ceiling
and upper belt
5˝between
ceiling and top
of lower belt
All dimensions shown in inches
Belt dimensions are same as long fan assembly
9½˝distance
between belts
All dimensions shown in inches
Pulley
adjustable
within 2˝span