Fanimation EDGEWOOD FP9052 Series User manual

Español p. 21
6
EDGEWOOD™ 52 CEILING FAN
MODEL #FP9052**
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-888-567-2055, 8 a.m.-5 p.m., EST, Monday-Friday.
ATTACH YOUR RECEIPT HERE AND REGISTER YOUR FAN AT FANIMATION.COM
READ AND SAVE THESE INSTRUCTIONS
Date Code Purchase Date Net Weight 22.93 lbs (10.40 kgs)
For best and quickest service please provide date code. You can find the date code on the carton
or top of fan housing.

Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
Additional Safety Instructions
2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such
as a tag, to the service panel.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before
servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. Do not operate reversing switch until fan blades have come to a complete stop.
6. The appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised to
ensure that they do not play with the appliance.
1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70) and Local Codes. The ceiling fan
must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed
electrician.
3.
4. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades.
The fan base must be securely mounted and capable of reliably supporting at least 35 lbs. See page 5 of owner’s manual for
Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not have adequate electrical
5.
knowledge or experience, have your fan installed by licensed electrician.
support requirements. Consult a qualified electrician if in doubt.
6. This fan is to be used in wet locations.
7. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it should be connected to a grounded
conductor power supply. If the conductor of a fan is identified as an ungrounded conductor, then it should be connected to an
ungrounded conductor power supply. If the conductor of a fan is identified for equipment grounding, then it should be connected to an
equipment grounding conductor.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product could result in personal injury or property
damage.
WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade holder) when installing the brackets,
balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
WARNING: Do not operate this fan with a variable (Rheostat) wall controller or dimmer switch. Doing so could result in damage to the
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Please note that changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL USE ISOLATING
WALL CONTROL/SWITCH.
WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.

1. LIMITED LIFETIME MOTOR WARRANTY - If any part of your fan motor fails, due to a defect in materials or workmanship during the
lifetime of the original purchaser, Fanimation will provide the replacement part free of charge, when the defective fan is returned
to our national service center. Proof of purchase is required. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
2. ONE YEAR MOTOR LABOR WARRANTY - If your fan motor fails at any time within one year from the original purchase, due to
defects in materials or workmanship, labor to repair the motor will be provided free of charge at our national service center. Purchaser will
be responsible for labor charges after this one-year period. Customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs or replacement.
3. If any other part of your fan fails at any time within one year after original purchase, due to a defect in materials or workmanship, we
will repair, or replace, at our option, the defective part free of charge for parts and labor performed at our national service center.
4. Because of varying climate conditions, this warranty does not cover changes in the finish, including rusting, pitting, corroding,
tarnishing, or peeling.
5. This warranty is void and does not apply to damage from improper installation, neglect, accident, misuse, exposure to extremes of
heat or humidity, or as a result of any modification to the original product.
6. All costs of removal and reinstallation of the fan are the sole responsibility of the owner of the fan and not the store that sold the fan or
Fanimation.
7. Fanimation reserves the right to modify or discontinue any product at any time and may substitute any part under this warranty.
8. Under no circumstances may a fan be returned without prior authorization from Fanimation. The receipt of purchase must accompany
authorized returns and must be sent freight prepaid to Fanimation. The fan to be returned must be properly packed to avoid
damage in transit; Fanimation will not be responsible for any damage resulting from improper packaging.
9. It is understood that any repair or replacement is the exclusive remedy available from Fanimation. There is no other expressed or
implied warranty. Fanimation hereby disclaims any and all implied warranties, including, but not limited to those of merchantability and
fitness for a particular purpose to the extent permitted by law. Some states do not allow limitations on implied warranties. Fanimation will
not be liable for incidental, consequential, or special damages arising out of or in conjunction with product use or performance, except as
may otherwise be accorded by law. This warranty gives you special legal rights and you may also have other rights that vary from state to
state.
10. A certain amount of wobble is normal and should not be considered a problem or a defect.
LIMITED LIFETIME WARRANTY
Extends to the original purchaser of a Fanimation fan from an authorized Fanimation dealer/retailer only
Table of Contents
Unpacking Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Energy Efficient Use of Ceiling Fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical and Structural Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Assemble Your Ceiling Fan (Downrod) . . . . . . . . . . . . . . . . . . . . .
How to Assemble Your Ceiling Fan (Close-to-Ceiling) . . . . . . . . . . . . . . .
How to Hang Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Wire Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Install Your Canopy Housing (Downrod) . . . . . . . . . . . . . . . . . .
How to Install Your Canopy Housing (Close-to-Ceiling) . . . . . . . . . . . . .
4
5
5
7
8
9
11
12
13
14
14
15
16
16
17
18
19
How to Assemble Your Ceiling Fan Blades . . . . . . . . . . . . . . . . . . . . . . .
How to Assemble Your Switch Cup Assembly . . . . . . . . . . . . . . . . . . . .
How to Operate Your Ceiling Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Clean Your Ceiling Fan Blades . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exploded-View Illustration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Unpacking Instructions
NOTE: Place the parts from the loose parts bags in a small
container to keep them from being lost. If any parts are
missing, contact your local retailer.
Materials
Before assembling your ceiling fan, refer to section on
proper method of wiring your fan (page 11). If you feel you
do not have enough wiring knowledge or experience, have
your fan installed by a licensed electrician.
For your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been
completed and will be helpful in finding your place should you be interrupted.
WARNING
4
This manual is designed to make it as easy as possible for you to assemble,
install, operate and maintain your ceiling fan
Wiring outlet box and box connectors must be of type
required by local code. The minimum wire would be a 3-
conductor (2-wire with ground) of the following size:
nstalled ire ength ire i e
p to ft
ft
Tools Needed for Assembly
(Not Included)
• One Phillips head screwdriver
• One ¼˝ blade screwdriver
• One stepladder
• One wire stripper
1. Check to see that you have received the following parts:
NOTE: If you are uncertain of part description, refer to exploded view illustration.
WARNING
Do not install or use fan if any part is damaged or missing. This product is designed to use only those parts supplied with
this product and/or any accessories designated specifically for use with this product by Fanimation. Substitution of parts
or accessories not designated for use with this product by Fanimation could result in personal injury or property damage.
Contact your retail store for missing or damaged parts.
Switch Cup Assembly (1)
Canopy Trim Ring (1) Blade Holder Set (1)
Hanger Bracket
Assembly (1) Motor Coupling
Cover Assembly (1)
Hardware Bags
Motor Assembly (1)
Ceiling Canopy (1)
Downrod/Hanger Ball Assembly (1)
– Downrod (1)
– Hanger Ball (1)
– Set Screw (1)
– Hairpin Clip (1)
– Clevis Pin (1)
– Pin (1)
Canopy Screw Cover (1)
3/16"-24
Serrated Head Screws,
Stainless Steel
(21)
Wire Connectors
(4)
Fan Fob
(1)
Pull Chain Coupler
(1)
1/4"-20
Phillips Head Screws,
Stainless Steel
with Lock Washers,
Stainless Steel
(11)
Flat Washers,
Stainless Steel
(21)
Flat Washers,
Stainless Steel
(2)
Blade Set (1)
#8-32
Outlet Box Screws,
Stainless Steel
(2)
Safety Cable Kit
Safety Cable
(1)
Cable Clamp
(1)
Flat Washer,
Stainless Steel
(1)
Lag Bolt
(1)

Energy Efficient Use of Ceiling Fans
Electrical and Structural Requirements
Ceiling fan performance and energy savings rely
heavily on the proper installation and use of the
ceiling fan. Here are a few tips to ensure efficient
product performance.
Using the Ceiling Fan Year Round
Summer Season: Use the ceiling fan in the
counterclockwise direction. The airflow produced by
the ceiling fan creates a wind-chill effect, making you
“feel” cooler. Select a fan speed that provides a
comfortable breeze, lower speeds consume less
energy.
Winter Season: Reverse the motor and operate the
ceiling fan at low speed in the clockwise direction.
This produces a gentle updraft, which forces warm air
near the ceiling down into the occupied space.
Remember to adjust your thermostat when using your
ceiling fan-additional energy and dollar savings could
be realized with this simple step!
Choosing the Appropriate Mounting Location
Ceiling fans should be installed, or mounted, in the middle
of the room and at least 7 feet from floor to the blade and
18 inches from wall to the blade. If ceiling height allows,
install the fan 8 - 9 feet from floor to the blade for optimal
airflow. Consult your Fanimation Retailer for optional
mounting accessories.
Turn Off When Not in the Room
Ceiling fans cool people, not rooms. If the room is
unoccupied, turn off the ceiling fan to save energy.
Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 HZ, 15 Amp Circuit.
Electrical code requires use of a fan-rated outlet box to
support the extra weight and motion associated with a
ceiling fan. A fan-rated box will be labeled as such and
typically supports up to a 70lb ceiling fan. Fan-Rated
Outlet Boxes vary in ratings and design. Ensure the
ratings of your ceiling fan outlet box meet the
requirements for the ceiling fan being installed. Figure
1, Figure 2 and Figure 3 depicts different structural
configurations that may be used for mounting the outlet
box.
Low profile box (Figure 1)
A 1/2-in.-deep pancake box is meant to be screwed to a
joist or block. It’s used if only one cable is coming into the
box. It is also available in a saddle-mount configuration.
Deep box (Figure 2)
A 2-1/4-in.-deep box can be attached to blocking between
joists and is roomy enough to handle more than one cable.
CEILING JOIST
CEILING OUTLET BOX
Figure 1
Figure 2
CEILING JOIST
2" x 4"
2" x 4"
CEILING OUTLET BOX
5

Electrical and Structural Requirements (Continued)
6
If your fan is to replace an existing light fixture, turn
electricity off at the main fuse box at this time and remove
the existing light fixture.
Turning off wall switch is not sufficient. To avoid
possible electrical shock, be sure electricity is turned off
at the main fuse box before wiring. All wiring must be in
accordance with National and Local codes and the ceiling
fan must be properly grounded as a precaution against
possible electrical shock.
Deep box with brace (Figure 3)
Paired with a deep box, this hanger is meant to span
between two joists and takes the place of wooden blocking.
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done or approved by a licensed
electrician.
Figure 3
CEILING JOIST
CEILING
OUTLET BOX
To reduce the risk of fire, electric shock, or personal injury,
mount to outlet box marked acceptable for fan support of
15.9 kg (35 lbs) or less and use mounting screws provided
with the outlet box. Most outlet boxes commonly used for
the support of luminaires are not acceptable for fan support
and may need to be replaced, consult a qualified electrician
if in doubt.
Do not operate this fan with a variable (Rheostat) wall
controller or dimmer switch. Doing so could result in
damage to the ceiling fan’s remote control unit.
WARNING
WARNING
WARNING
WARNING

Set Screws and
Locking Nuts (2)
WARNING
It is critical that the clevis pin in the downrod support
is properly installed and the set screws and nuts are
securely tightened. Failure to do so could result in the
fan falling.
Set Screw
Hairpin Clip
Clevis Pin
Clevis Pin
Downrod
Hairpin Clip
Downrod
Black, White, Blue
wires and Safety Cable
Downrod
Pin
Hanger Ball
5. Slide downrod into the downrod support on top of
the motor. Install the clevis pin by aligning the holes
in the downrod support with holes in the downrod.
Secure clevis pin with hairpin clip. Tighten the two set
screws with nuts in the downrod support. (Figure 5)
2. Remove the hanger ball portion from the downrod/
hanger ball assembly by loosening the set screw in
the hanger ball until the ball falls freely down the
downrod. Remove the pin from the downrod, then
remove the hanger ball. Retain the pin and hanger ball
for reinstallation in Step 7. (Figure 2)
7
Figure 2
Figure 3
Figure 4
Figure 5
3. Remove the hairpin clip and clevis pin from the
bottom of downrod. Retain the pin and clip for
reinstallation in step 5. (Figure 3)
4. Loosen the two set screws and locking nuts in the
downrod support of the motor assembly. Route the
black, white, blue wires and safety cable through the
downrod. (Figure 4)
How to Assemble Your Ceiling Fan (Downrod)
1. Remove and discard the five rubber motor stops
from the motor assembly by removing the screws.
(Figure 1) Motor Stops
Figure 1

6 TO 9 IN
2. Alternating positions, remove three motor coupling
screws from motor assembly and retain the screws
for Step 4. (Figure 2)
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
8
Figure 7
Figure 8
Figure 2
How to Assemble Your Ceiling Fan (Downrod)-Continued
How to Assemble Your Ceiling Fan (Close-to-Ceiling)
7. Reinstall the hanger ball on the downrod as follows.
Route the black, white, blue wires and safety cable
through the hanger ball. Position the pin through the
two holes in the downrod and align the hanger ball so
the pin is captured in the groove in the top of the
hanger ball. Pull the hanger ball up tight against the
pin. Securely tighten the set screw in the hanger ball.
A loose set screw could cause fan wobble. (Figure 7)
8. Cut off excess lead wire approximately 6 to 9
inches above top of the downrod. Strip insulation
off 1/2 inch from the end of each lead wire. (Figure 8)
CAUTION
All set screws must be checked, and retightened where
necessary before installation.
1. Remove and discard the five rubber motor stops
from the motor assembly by removing the screws.
(Figure 1) Motor Stops
Figure 1
Canopy Trim
Ring
6. Route wires and safety cable through motor coupling
cover, canopy trim ring, canopy screw cover and ceiling
canopy. (Figure 6) Ceiling Canopy
Canopy Screw
Cover
Motor Coupling
Cover
Figure 6

4. Align the three big slots in the ceiling canopy to the
three screws in the motor coupler. Firmly attach the
canopy cover to the motor with the previously
removed screws. (Figure 4)
Motor
Assembly
Screws (3)
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
Ceiling
Canopy
9
Figure 4
NOTE: If you are not sure if the outlet box is
grounded, contact a licensed electrician for advise,
as it must be grounded for safe operation.
WARNING
WARNING
Ceiling
Floor
No
less than
7 ft
Main Fuse Box
How to Assemble Your Ceiling Fan (Close-to-Ceiling)-Continued
How to Hang Your Ceiling Fan
To avoid possible fire or shock, be sure electricity is
turned off at the main fuse box before hanging.
(Figure 1)
The fan must be hung with at least 7’ of clearance from
floor to blades. (Figure 2)
Figure 1
Figure 2
3. Route your fan wires and safety cable through the
canopy trim ring and ceiling canopy. (Figure 3)
Ceiling
Canopy
Canopy
Trim Ring
Motor
Assembly
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM
Figure 3

NOTE: SUPPLY WIRES
AND FAN WIRES OMITTED
FOR CLARITY
Attach Safety
Cable To Ceiling
Support Cable
Tab
Downrod/Hanger
Ball Assembly
WARNING
The outlet box must be securely anchored. Hanger
bracket must seat firmly against outlet box. If the outlet
box is recessed, remove wall board until bracket
contacts box. If bracket and /or outlet box are not
securely attached, the fan could wobble or fall.
Wood Member
(2" X 4" Approx.) Ceiling Joist
Ceiling
Ceiling
Support Hanger Bracket
Outlet
Box
3. Using the 3/8˝ x 2˝ lag bolt and flat washer, attach
safety cable to ceiling joist or wood structural member.
The lag bolt will pass through the flat washer, safety
cable loop, and into the building structure (Figure 4).
You will first drill a 1/4˝ pilot hole into the building
structure to prevent splitting or cracking.
NOTE: Ceiling support cable cannot be secured to
outlet box only, it must be directly secured to ceiling
joist or structural member using the 3/8˝ x 2˝ lag bolt
and flat washer. (Figure 4)
4. Make sure the electrical supply wires, including the
hanger bracket grounding wire and safety cable are
pulled through the downrod, between the hanger
bracket and the outlet box so that electrical
connections can be made later.
5. Carefully lift the fan and seat the downrod/hanger
ball assembly onto the hanger bracket that was just
attached to the ceiling joist. Be sure the groove in the
ball is lined up with tab on the hanger bracket.
(Figure 5)
6. Attach the safety cable to ceiling support cable.
Slide cable clamp onto safety cable (from fan). Place
the end of cable through the loop of ceiling support
cable. Pull as much cable through loop as possible.
Feed end of cable into clamp hole and firmly tighten
screw (Figure 5). Cut off excess safety cable.
NOTE: If you have installed your fan with the Downrod,
skip steps 7, 8, 9 and 10.
10
Figure 4
Figure 5
WARNING
WARNING
Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.
To avoid possible shock, do not pinch wires between
the hanger ball assembly and the hanger bracket.
How to Hang Your Ceiling Fan (Continued)
For Downrod Fan
2. Securely attach the hanger bracket to the outlet
box using the outlet box screws and washers
supplied with the fan. (Figure 4)
1. Completely remove one screw from either side of
the hanger bracket--be sure it is the screw to your
right when facing it--and keep for reinstallation on
page 12 or 13 (How to Install Your Canopy Housing
). Loosen the other two screws that were not removed.
(Figure 3)
Figure 3

10. Attach the safety cable to ceiling support cable.
Slide cable clamp onto safety cable (from fan). Place
the end of cable through the loop of ceiling support
cable. Pull as much cable through loop as possible.
Feed end of cable into clamp hole and firmly tighten
screw (Figure 8). Cut off excess safety cable. You can
now proceed with the electrical wiring of your fan.
8. Using the 3/8˝ x 2˝ lag bolt and flat washer, attach
safety cable to ceiling joist or wood structural member.
The lag bolt will pass through the flat washer, safety
cable loop, and into the building structure (Figure 6).
You will first drill a 1/4˝ pilot hole into the building
structure to prevent splitting or cracking.
NOTE: Ceiling support cable cannot be secured to
outlet box only, it must be directly secured to ceiling
joist or structural member using the 3/8˝ x 2˝ lag bolt
and flat washer. (Figure 6)
For Close-to-Ceiling Fan
7. Securely attach the hanger bracket to ceiling fan
outlet box using the outlet box screws and washers
supplied with the fan. (Figure 6)
9. Hook the motor assembly onto the hanger bracket
assembly as shown (Figure 7).
1. Connect the green grounding lead from the hanger
ball and the green grounding lead from the hanger
bracket to the supply grounding conductor (this may
be a bare wire or wire with green colored insulation).
Securely connect wires with wire connectors supplied.
(Figure 2)
2. Securely connect the white fan motor wire to the
white supply (neutral) wire using wire connector
supplied. Securely connect the black fan motor wire
and blue wire to the black supply wire using wire
connector supplied. (Figure 2)
Outlet Box
Hook
Hanger Bracket
Motor
Assembly
WARNING
To avoid possible electrical shock, be sure electricity
is turned off at the main fuse box before wiring.
(Figure 1)
How to Wire Your Ceiling Fan
Main Fuse Box
Household
Supply
White
Blue
Listed Outlet Box
Black
Black
Green Wire
(Ground) from
Supply
Green Wire
(Ground) from
Hanger Bracket
Green Wire
(Ground) from
Hanger Ball
11
Figure 6
Figure 7
Figure 1
Figure 2
Wood Member (2" X 4" Approx.) Ceiling Joist
Ceiling
Ceiling
Support Hanger Bracket
Outlet
Box
NOTE: SUPPLY WIRES
AND FAN WIRES OMITTED
FOR CLARITY
Attach Safety
Cable To Ceiling
Support Cable
Figure 8
How to Hang Your Ceiling Fan (Continued)

WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not
operate fan until the blades are in place. Noise and
fan damage could result.
3. After connections have been made, turn leads
upward and carefully push leads into the outlet box,
with the white and green leads to one side of the box
and the black leads toward the other side. (Figure 3)
WARNING
To avoid possible fire or shock, make sure that the
electrical wires are completely inside the canopy
housing and not pinched between the housing and
the ceiling.
1. Slide the ceiling canopy over the mounting bracket
with the two loosened screws going into the “L” slots in
the canopy. Be sure all wiring is tucked into the ceiling
canopy and is not pinched. Once the canopy is flush
with your ceiling, turn clockwise to seat the screws into
the keyed portion of the slot. Tighten the screws and
install the remaining two screws removed in step 1 of
page 10 (How to Hang Your Ceiling Fan) to secure
the ceiling canopy to the hanger bracket. (Figure 1)
2. Assemble the canopy screw cover, by twisting in a
clockwise direction and up to the ceiling canopy.
(Figure 2)
3. Push the canopy trim ring up to conceal the screws,
such that the mounting tabs seat into the dimpled
grooves in the ceiling canopy midway between the
screws. (Figure 3)
How to Wire Your Ceiling Fan (Continued)
How to Install Your Canopy Housing (Downrod)
Wire Connectors
HARDWARE USED:
X 3
Ceiling Canopy
Canopy Screw
Cover
Canopy Trim Ring
12
Figure 1
Figure 2
Figure 3
Household
Supply
Listed
Outlet Box
Black Wire
from Supply
Green Wire
(Ground) from
Supply
Green Wire
(Ground) from
Hanger Bracket
Green Wire
(Ground) from
Hanger Ball
White Wire
from Fan
Blue Wire
from Fan
Black Wire
from Fan
White Wire
from Supply
Figure 3

1. Lift the fan off the hanger bracket hook and mount
your fan by sliding the ceiling canopy over the
mounting bracket with the two loosened screws going
into the “L” slots in the canopy. Be sure all wiring is
tucked into the ceiling canopy and is not pinched.
Once the canopy is flush with your ceiling, turn
clockwise to seat the screws into the keyed portion of
the slot. Tighten the screws. (Figure 1)
How to Install Your Canopy Housing (Close-to-Ceiling)
NOTE: MOTOR WIRES
HAVE BEEN OMITTED
FROM DIAGRAM Screw
Hanger Bracket
Slot
Slot
Mounting
Tab (4)
Dimpled
Groove
Screw
2. Install the remaining two screws removed in step 1
of page 10 (How to Hang Your Ceiling Fan) to secure
the ceiling canopy to the hanger bracket. (Figure 2)
3. Push the canopy trim ring up to conceal the screws,
such that the mounting tabs seat into the dimpled
grooves in the ceiling canopy midway between the
screws. (Figure 3)
Canopy
Trim Ring
13
Figure 1
Figure 2
Figure 3

3/16"-24
Serrated
Head Screw
X 20
Flat Washer X 20
1/4"-20
Screw X 10
CAUTION
Blade Holder
1/4"-20 S crew
(2 Per Assembly)
Figure 1
Figure 2
Figure 1
HARDWARE USED:
HARDWARE USED:
How to Assemble Your Ceiling Fan Blades
How to Assemble Your Switch Cup Assembly
1. Position the blade over the blade holder with
threaded posts showing. Make sure the bottom edge
of the blade is fully seated against the blade holder.
With a phillips screwdriver, tighten 3/16"-24 serrated
head screws with flat washers to secure the blade to
the blade holder. (Figure 1)
1. Remove the three screws from the switch cup
assembly and retain screws for later. (Figure 1)
2. Attach assembled blade holders to the motor
hub using the provided screws with lock washers in
HARDWARE bag. Make sure the screws securing
the blade holders to the motor hub are tight and that
the blade holders are properly seated. (Figure 2)
NOTE: Periodically check blade holder hardware
and resecure if necessary.
3/16"-24
Serrated Head Screw and
Flat Washer (4 each per blade)
Blade Holder
To reduce the risk of personal injury, do not bend the
blade holders when installing, balancing the blades or
cleaning the fan. Do not insert foreign objects in
between the rotating blades.
Switch Cup
Assembly
14
Blade
CAUTION
Do not connect fan blades until the fan is completely
installed. Installing the fan with blades assembled
may result in damage to the fan blades.

How to Assemble Your Switch Cup Assembly (Continued)
How to Operate Your Ceiling Fan
2. Securely attach the 9-pin switch cup connector to
the wiring harness socket within the adapter
assembly. (Figure 2)
3. Assemble the switch cup assembly onto the
housing adapter with previously removed screws.
(Figure 3)
1. Restore electrical power to the outlet box by turning
the electricity on at the main fuse box. (Figure 1)
2. Install the fan fob and pull chain coupler. (Figure 2)
3. Check the operation of the fan by gently pulling on
the fan fob. (Figure 3)
Switch Cup
Assembly
WARNING
The color label on these two connectors must
correspond to each other.
WARNING
Check to see that all connections are tight, including
ground, and that no bare wire is visible at the wire
connectors, except for the ground wire. Do not operate
fan until the blades are in place. Noise and fan damage
could result.
Main Fuse Box
Fan Fob
Pull Chain
Coupler
Fan Pull Chain Operating Sequence
1st Pull High
2nd Pull Medium
3rd Pull Low
4th Pull Off
15
Figure 2
Figure 3
Figure 1
Figure 2
Figure 3
Fan Fob X 1
Pull Chain Coupler X 1
HARDWARE USED:

16
4. If airflow is desired in the opposite direction, turn the
fan off and wait for the blades to stop turning. Slide the
reverse switch on the switch cup assembly to the
opposite position and turn fan on again. (Figure 4)
Periodic cleaning of your new ceiling fan is the only
maintenance necessary.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive cleaning agents are not required and should be
avoided to prevent damage to finish.
Periodic light dusting of the blades is recommended.
A feather duster will work best.
Avoid using water, cleansers, or harsh rags, which
can warp and ruin the blades.
How to Operate Your Ceiling Fan (Continued)
Maintenance
How to Clean Your Ceiling Fan Blades
Reverse
Switch
Switch Cup
Assembly
Reverse Switch Information
Season Rotation Direction Switch Position
Summer Counterclockwise Left
Winter Clockwise Right
CAUTION
Do not use water when cleaning your ceiling fan. It
could damage the motor or the blades and create the
possibility of electrical shock.
Figure 4

WARNING
Trouble Probable Cause Suggested Remedy
1. Check main and branch circuit fuses or circuit
breakers.
2. Check line wire connections to fan and switch wire
connections in the switch housings.
CAUTION: Make sure main power is turned off !
CAUTION: Make sure main power is turned off !
3. Make sure reversing switch position is all the way to
one side.
1. Attach blades to fan before operating.
2. Check to make sure all screws in motor housing are
snug (not over-tight).
3. Check to make sure the screws which attach the fan
blade holders to the motor flywheel are tight.
4. Check to make sure wire connectors in switch
housing are not rattling against each other or against
the interior wall of the switch housing.
1. Tighten both setscrews securely in downrod support.
2. Tighten the setscrew in the downrod/hanger ball
assembly.
3. Check to be sure screws which attach the fan blade
holders to the flywheel are tight.
4. Check to be sure the fan blade holders seat firmly
and uniformly to the surface of the motor housing. If
holders are seated incorrectly, loosen the screws
and retighten.
5. Tighten the hanger bracket screws to the outlet box,
1. If possible, consider using a longer downrod (not
included, you can buy the longer downrod from
fanimation.com).
and secure outlet box.
17
Troubleshooting
For your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan.
1. FAN WILL NOT START
2. FAN SOUNDS NOISY
3. FAN WOBBLES
EXCESSIVELY
4. NOT ENOUGH AIR
MOVEMENT
1. Fuse or circuit breaker blown.
2. Loose power line connections to the fan, or loose
switch wire connections in the switch housing.
3. Reversing switch in neutral position.
1. Blades not attached to fan.
2. Loose screws in motor housing.
3. Screws securing fan blade holders to motor flywheel
are loose.
4. Wire connectors inside housing rattling.
5. Screws holding blades to blade holders are loose.
6. Lower housing support set screw loose.
1. Setscrew in downrod support is loose.
2. Setscrew in downrod/hanger ball assembly is loose.
3. Screws securing fan blade holders to motor hub are
loose.
4. Blade holders not seated properly.
5. Hanger bracket and/or ceiling outlet box is not
securely fastened.
5. Tighten screws securely.
6. Tighten set screw securely.

18
Parts List
Model #FP9052**
1 Hanger Bracket Assembly
2 Downrod/Hanger Ball Assembly
3 Canopy Trim Ring
4 Ceiling Canopy
5 Canopy Screw Cover
6 Motor Coupling Cover Assembly
7 Motor Assembly
8Blade Holder Set
9 Blade Set
10 Switch Cup Assembly
Hardware Bag Containing:
Blade Holder Mounting Hardware Bag Containing:
Before discarding packaging materials, be certain all parts have been removed.
Blade Mounting Hardware Bag Containing:
11
APGAC1113RBL
ADR1SS-45**
PPAC1081**
PPAC1003**
PPAC1102**
APPAC1404**
AMA9052**
AP905215**
AP905205**
AP905202**
HDWFP9044**
Wire Connectors (4)
Flat Washers, Stainless Steel (21)
3/16˝–24 Serrated Head Screws, Stainless Steel (21)
How To Order Parts
When ordering repair parts, always give the
following information:
• Part Number
• Part Description
• Fan Model Number
Contact your retail store for repair parts.
Safety Cable Kit
Flat Washers, Stainless Steel (2)
1/4˝-20 Phillips Head Screws, Stainless Steel
with Lock Washers, Stainless Steel (11)
Ref. # Description Part #
Fan Fob (1) / Pull Chain Coupler (1)
#8-32 Outlet Box Screws, Stainless Steel (2)

19
1
11
2
3
4
5
6
7
11
9
10
11
11
11
11
8
NOTE: The illustration shown is not to scale or its actual configuration may vary.
EDGEWOOD 52
Model FP9052**
Exploded-View Illustration
™

2020/11 V.01
Copyright 2020 Fanimation
10983 Bennett Parkway
Zionsville, IN 46077
Phone: [phone]
Outside U.S.: 317-733-4113
FAX: [phone]
FANIMATION.COM