Fanstel ST150 User manual
Amplified Call Waiting ID
Speakerphone
OWNER’S MANUAL
MODEL ST140, ST150
802
Table of Contents
SETTING UP AND INSTALLING YOUR PHONE.................................................1
Introduction.........................................................................................................1
Important Safety Instructions..............................................................................1
Parts Checklist....................................................................................................2
Installation ..........................................................................................................4
Adjusting the Display Angle................................................................................6
Adjusting the Display Contrast ...........................................................................6
Adjusting Handset Receiver Volume..................................................................6
Adjusting Headset Receiver Volume..................................................................6
Adjusting Speakerphone Receiver Volume........................................................7
Amplify or Volume Reset Override .....................................................................7
USING THE TELEPHONE.....................................................................................8
Making a Call......................................................................................................8
Editing Telephone Number before Dialing .........................................................8
Receiving a Call..................................................................................................8
Receiving a Call Waiting Call .............................................................................8
Switching Between the Handset and the Speakerphone...................................8
Switching Between the Headset and the Speakerphone...................................9
Switching Between the Handset and the Headset .............................................9
Redialing.............................................................................................................9
Accessing Outside Lines ....................................................................................9
Putting a Call on Hold.......................................................................................10
Muting a Call.....................................................................................................10
Telephone Directory .........................................................................................10
Storing a New Number and Name in Directory ................................................10
Using the Keypad to Enter a Name..................................................................11
Copying the Caller’s Number and Name to the Directory ................................11
Dialing Telephone Numbers from the Directory ...............................................12
Deleting Entries in the Directory.......................................................................12
Storing a New Number and Name in the Memory Buttons ..............................13
Copying the Caller’s Number and Name to a Memory Button .........................13
Programming for One-Touch Call Forwarding .................................................14
CALLER ID..........................................................................................................16
Caller ID Service and Call Waiting Caller ID Service.......................................16
Caller ID Display...............................................................................................16
New Calls and Total Calls ................................................................................16
Viewing the Caller ID List .................................................................................17
Calling Back a Number From the Caller ID List ...............................................17
Deleting a Call From the Caller ID List .............................................................17
Deleting All Calls from the Caller ID List ..........................................................18
Using Call Waiting Caller ID .............................................................................18
In Use Indication...............................................................................................18
Message Indication...........................................................................................18
Accessing Voice Mailbox..................................................................................18
Clearing the Message Waiting Indicator ..........................................................19
UNAVAILABLE, PRIVATE CALL and ERROR Messages...............................19
IN CASE OF DIFFICULTY...................................................................................20
Resetting Your Telephone's Programming ......................................................20
Maintenance Information..................................................................................20
Troubleshooting................................................................................................20
LIMITED WARRANTY.........................................................................................21
Warranty Limitation...........................................................................................21
What This Warranty Does Not Cover ...............................................................22
State Law Rights ..............................................................................................22
FCC REGISTRATION AND REPAIR INFORMATION .......................................22
Connection and Use with the Nationwide Telephone Network........................22
Notification to the Telephone Company ...........................................................22
Repair Instructions............................................................................................23
Rights of the Telephone Company...................................................................23
Interference Information: Part 15 of FCC Rules..............................................23
Page 1
Setting Up and Installing Your Phone
Introduction
Congratulations on the purchase of your new telephone. It has been manufactured to very
high quality standards for convenient and reliable service. This telephone can be used
with "Call Identification (Caller ID) Service" and/or "Call Waiting Caller ID Service" that is
provided by your local telephone company. There is a fee for these services by your local
telephone company, and they may not be available in all areas. When used with these
services, your telephone displays the telephone number or the telephone number and
name of each caller before you answer the call allowing you to screen your calls.
In addition to Caller ID services, if you subscribe to voice mail services from your local
telephone company, voice mail waiting indicators will inform you there is a message
waiting in your voice mailbox.
Important Safety Instructions
Before using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons, including the
following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the telephone jack and the power outlet before cleaning. Do not
use liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water, such as near a bathtub, sink, laundry tub, in a wet
basement, or near a swimming pool.
5. Do not place this product on an unstable cart, stand, or table. Serious damage may result
if the product falls.
6. Slots or openings in the cabinet and the back and bottom are provided for ventilation to
protect the phone from overheating. These openings must not be blocked or covered. The
product should never be placed near or over a radiator or heat register.
7. This product should be operated only from the type of power source indicated on the
marking label.
8. Do not allow anything to rest on the power cord. Do not locate this product where the
cord will be abused by persons walking on it. Do not attach the power cord to building
surfaces.
9. Do not overload wall outlets and extension cords as this can result in the risk of fire or
electric shock.
10. Never push any objects into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
11. If this product does not operate normally, see the “In Case of Difficulty” section in this
owner's manual. If you cannot resolve the problem, or if the product is damaged, refer to
the "Limited Warranty" section of this owner's manual. Opening the product or
reassembling it incorrectly may expose you to dangerous voltages or other risks, and will
void the warranty.
12. Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions: (a) When the power supply cord or plug is damaged or
frayed. (b) If liquid has been spilled into the product. (c) If the product has been exposed
Page 2
to rain or water. (d) If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating instructions. (e)
If the product has been dropped or the cabinet has been damaged. (f) If the product
exhibits a distinct change in performance.
13. Avoid using a telephone during an electrical storm. There may be a remote risk of electric
shock and/or hearing damage from lightning.
14. Do not use the telephone near a gas leak even to report the leak.
Parts Checklist
Remember to save your sales receipt in case you ever need warranty service.
Check to make sure your package includes the items described below:
1. Telephone Base 4. AC/DC Adapter
2. Telephone Handset 5. Handset Cord
3. Telephone Line Cord
Make sure you have a modular wall jack near the place you have chosen to install the
telephone. If you have an older phone jack, you will need to buy a modular jack adapter.
Page 3
Controls and Functions
1. LCD display
2. Hook switch
3. Telephone keypad
4. Volume - to adjust receiver volume for handset, speaker, and headset.
5. Message light - Visual message waiting indicator.
6. ◑button – to adjust LCD contrast.
7. Amplify – when lit, receiver volume is not reset when on hook.
8. - to review upward from the oldest caller ID record.
9. - to move curser left during programming.
10. - to review downward from the newest caller ID record.
11. - to move curser right during programming.
12. Dial/Enter button – to dial number displayed or to accept entry
13. Directory button – to begin using directory features.
Page 4
14. Flash button – during a call, to access telco’s calling features.
15. Mute with indicator – to mute transmitter, LED is on when active.
16. Ãbutton – to connect or to disconnect voice path to headset.
17. Redial/Pause button
18. Hold with indicator – to put a call on hold, LED is on when active.
19. Goodbye – to hang up a call at any time.
20. Speaker – to activate or to deactivate speakerphone.
21. Menu – to set telephone operation parameters.
22. Save – to begin programming of memory buttons or directory.
23. Delete – to delete one or all records in caller ID log or directory
24. M1 – programmable memory button
25. M2 – programmable memory button
26. M3 – programmable memory button
27. M4 – programmable memory button
28. M5 – programmable memory button
29. M6 – programmable memory button
30. Messages button – to dial voice mailbox access code.
31. index card
32. Speakerphone indicator
Installation
1. Plug one end of the flat telephone line cord into the line jack on the back of the phone
where it is labeled "TEL.LINE" and plug the other end into your modular telephone wall
jack.
Page 5
#00
_ _ _
ENTER AREA CODE
7 DIGITS DIAL
#00
SELECT LANGUAGE
1 2 3
>ENG ESP FRA
#00
3 0 3
ENTER AREA CODE
7 DIGITS DIAL
#00
_ _ _ - _ _ _ - _ _ _
ENTER AREA CODE
10 DIGITS DIAL
#00
7 2 0
ENTER AREA CODE
10 DIGITS DIAL
#00
- - - -
OUTSIDE ACCESS?
2. Connect the AC adapter to an electrical wall outlet and then connect the AC adapter
plug to the “DC 12V” jack on the back of the phone. Use only with a Class 2 power
source, plug polarity, 12V DC, AC adapter.
3. Connect one end of the coiled Handset Cord to the jack on the left side of the phone
and connect the other end of the coiled Handset Cord to the jack on the handset
4. If you wish to use an Answering Machine, Modem, Fax Machine or other devices
along with your Caller ID telephone, you may plug one of these devices into the "DATA"
jack on the right side of the phone. The important thing to remember is that for the
Caller ID features to work properly the Caller ID telephone must be plugged directly into
the wall jack and other devices must be plugged into the Caller ID phone.
5. Selecting a language
When the phone is powered up for the first time, the
display flashes “SELECT LANUGAGE” and “>ENG
ESP FRA”.
To select English, press the “1” button.
To select Spanish, press the “2”button.
To select French, press the “3” button.
Then, press the Dial/Enter button to confirm the
selection.
6. Program your area code
(A) After selecting the language, the display flashes
"ENTER AREA CODE" and “7 DIGITS DIAL”.
(B) If you dial your local calls using 7 digits (e.g., 555-
1212), then enter your local area code, press the
Dial/Enter button, and go to Step C.
If you dial your local calls using 10 digits (e.g., 303-
555-1212), then enter “000” as the area code for 7
digits dial, and press the Dial/Enter button to go to
Step C.
(C) The display flashes “ENTER AREA CODE” and “10
DIGITS DIAL”.
Enter the area code(s) for numbers that you dial
using ten digits (e.g., 720-555-1234). You can store
up to three area codes for ten-digit dialing. Press
Dial/Enter when you are done. If there is no
number you dial using ten digits, then press
Dial/Enter.
7. The display indicates the “OUTSIDE ACCESS?”
prompt.
Page 6
#00
9 - - -
OUTSIDE ACCESS?
(A) If you don’t need to dial a number to access an outside line, press the Dial/Enter
button and go to Step 8.
(B) Alternatively, enter the outside line access code
(up to 4 digits), press the Dial/Enter button and go
to Step 8.
(C) If you enter an outside line access code by
mistake, press the Delete button or the Wbutton
to delete the digits.
The outside line access code is dialed prior to any number over 6 digits stored in the
directory, memory buttons, or the caller ID memory. A stored number with 6 or fewer
digits is considered an inside number. The outside line access code is not dialed for an
inside call. A PAUSE period or 3 seconds delay is inserted automatically between the
outside access code and the phone number.
8. Press the Menu or Save button to save these operating settings and to exit the menu
mode.
9. After installation, lift the telephone's Handset and listen for the dial tone. If there is no
dial tone, check to make sure all cords are firmly plugged into their jacks.
Note: Programming your area code will allow you to easily dial numbers that are in your
Caller ID list. See the Section “Calling Back a Number from the Caller ID List” for more
information on dialing calls from your Caller ID list.
Adjusting the Display Angle
You can optimize the LCD display by adjusting the viewing angle. To adjust the LCD
viewing angle, move the rear edge of the LCD module up or down.
Adjusting the Display Contrast
The display can be adjusted to suit the light level of your room and your viewing
preference. To make the contrast of the display lighter or darker, press the ◑button to
the right of the screen until the desired contrast is reached.
Adjusting Handset Receiver Volume
To adjust the handset receiver volume:
1. Lift the handset and listen to the dial tone.
2. Press the right side of the Volume button to increase the receiver volume.
3. Press the left side of the Volume button to decrease the receiver volume.
4. Replace the handset when the desired receiver volume is reached.
Adjusting Headset Receiver Volume
We recommend a headset without built-in amplifier. Amplifier for adjusting headset
receiver volume is built into this telephone.
Page 7
1. Press the ÃHeadset button and listen to the dial tone.
2. Press the right side of the Volume button to increase the receiver volume.
3. Press the left side of the Volume button to decrease the receiver volume.
4. Press the ÃHeadset button or the Goodbye button when the desired receiver volume
is reached.
Adjusting Speakerphone Receiver Volume
To adjust the speakerphone receiver volume:
1. Press the Speaker button and listen to the dial tone.
2. Press the right side of the Volume button to increase the receiver volume.
3. Press the left side of the Volume button to decrease the receiver volume.
4. Press the Speaker button or the Goodbye button when the desired receiver volume is
reached. Amplify or Volume Reset Override
If you set the Amplify switch on the back of phone to On, volume reset feature is disabled.
Handset and headset receiver volume level is the same as that of last call.
If the Amplify switch is set to Off, handset and headset receiver volume level is reset
when phone is on-hook.
Warning: Possible loud receiver volume when the Amplify switch is set to On and the
Amplify LED is lit.
Page 8
Using the Telephone
Making a Call
1. Pick up the Handset or press the Speaker button, and listen for a dial tone.
2. Using the Keypad, dial the desired telephone number. The number you are dialing
will appear on the display as you dial. When making a call or talking on the phone,
the "In Use" light will turn on indicating the phone is in use. This light will also be on
whenever another phone on the same phone line is in use.
Editing Telephone Number before Dialing
You can enter the telephone number you wish to dial before lifting handset or pressing the
Speaker button.
1. Use the keypad to enter the telephone number. The number is displayed on the
screen.
2. If you enter one or more wrong digits, press the button one or more times till
incorrect digits are erased.
3. When all digits of a telephone number are entered, press the Dial/Enter button. The
speakerphone is activated and the telephone number is dialed automatically.
Receiving a Call
1. When you hear the phone ring, simply pick up the handset from the handset cradle.
You may also press the Speaker button to answer the call using the speakerphone.
2. When you are finished talking, replace the handset in the handset cradle to end the
call. If you have been talking using the speakerphone, press the Speaker button to
hang up. You may press the Goodbye button to hang up at any time.
Receiving a Call Waiting Call
If you subscribe to call waiting services and are on a call when another caller calls your
phone number, you will hear a "beep" indicating there is another call coming in. If you
subscribe to Call Waiting ID services, the caller’s name and number can be displayed on
the screen. To answer the waiting call and/or switch between calls:
1. Press and release the Flash button to put the current call on "hold" and to answer the
incoming call. To switch back and forth between the two calls, press and release the
Flash button.
2. When a Call Waiting call comes in, you may also hang up the current call in order to
pick up the waiting call. When you are on a call you want to end and another call
comes in, hang up the telephone. The current call will be disconnected and after a
temporary delay, the phone will ring, allowing you to answer the waiting call.
Switching Between the Handset and the Speakerphone
To switch a call between the Handset and the Speakerphone during a conversation:
Page 9
1. While talking on the handset, press the Speaker button to activate the speakerphone.
The call can now be heard from the speakerphone.
2. While talking on the speakerphone, simply lift up the handset and the call will be
transferred to the handset and will no longer be heard on the speakerphone.
3. Hang up the handset. Hanging up the handset will not disconnect the call when the
Speakerphone is activated. You have to press the Speaker or the Goodbye button
to disconnect the call.
4. If the speakerphone is not activated, simply hang up the handset and the call will be
disconnected.
Switching Between the Headset and the Speakerphone
To switch between a call from the headset to the speakerphone during a conversation:
1. While talking on the Headset, press the Speaker button to activate the speakerphone.
The call can now be heard from the speakerphone.
2. Press the ÃHeadset button if you wish to activate the headset.
3. When you are finished with the conversation, press the Goodbye button, and the call
will be disconnected.
Switching Between the Handset and the Headset
To switch a call between the handset and the headset during a conversation:
1. While talking on the handset, press the ÃHeadset button to activate the headset.
The call can now be heard from the headset.
2. Press the ÃHeadset button again if you wish to switch back to the handset.
3. If you are using the headset, press the ÃHeadset button or the Goodbye button to
end a call.
4. If you are using the handset, simply hang up the handset to end a call.
Redialing
You can redial the last number you called with just one touch of the Redial button. This
lets you easily redial the same number again if the line was busy.
1. Pick up the handset or press the Speaker button and listen for a dial tone.
2. Press the Redial button and the last number you dialed will be shown on the display
and will be automatically dialed.
Accessing Outside Lines
If you need to dial an outside line access code to access outside lines, you should enter
the outside line access code during “Installation” procedures. If not, you may begin
entering of outside line access code by pressing the Menu button.
Outside line access code is dialed automatically before any number with 7 or more digits
stored in caller ID memories, directory, or memory buttons.
Page 10
ENTER NUMBER>
SAVE TO?
If you use the telephone keypad to dial a number, please dial the outside line access code
before the number.
Putting a Call on Hold
The Hold button allows you to place a call on "HOLD" without disconnecting the call.
When a call is on hold, you may hang up the handset without disconnecting the call.
1. Press the Hold button and the current call will be placed on hold. If you were talking
with the handset, you can then place the handset back in the handset cradle without
disconnecting the call. If you were talking with the speakerphone, the call is placed on
hold. The red Hold light inside the Hold button is lit when a call is on hold.
2. To continue the conversation, pick up the handset; press the Speaker or the
ÃHeadset button.
Muting a Call
In addition to putting a call on hold, muting a call is a good way to mute the phone so that
the person on the other end of the line will not hear what you are saying. You can
continue to hear the person on the other end.
1. Press the Mute button to mute the call. While a call is muted, the mute light inside
the Mute button is lit.
2. To release the mute, press the Mute button again and you will be able to continue the
conversation. Do not hang up the phone while a call is muted or the call will be
disconnected.
Telephone Directory
A directory, which holds up to 99 names and telephone numbers, makes dialing frequently
used phone numbers quick and easy. You can enter the numbers and names by using
the telephone keypad or by copying a caller’s name and number from the Caller ID call log
into directory.
You can search for a number in the directory by entering the first character of name
entered.
Storing a New Number and Name in Directory
To store a new number and name in the directory:
1. Press the Save button when the display shows no
caller’s number or name. The “SAVE TO?” prompt
appears on the display.
2. Press the Directory button, the “ENTER
NUMBER>“prompt appears on the display.
3. Use the keypad to enter the telephone number,
including the long distance prefix that you need to dial
this number. Insert a pause or multiple pauses where
Page 11
#00
4809484928
USE SAVE TO END
4809484928
ENTER NAME>
USE SAVE TO END
#25
480-948-4928
FANSTEL CORP
SAVE TO?
4809484928
SMITH
USE SAVE TO END
required by using the Pause button. Then press the Save button.
Note: If you need to dial an outside line access code, do NOT include the outside
line access code in the phone number you entered. The outside line access code is
dialed automatically if you entered it during the “Installation” procedures.
4. The third line of LCD displays “ENTER NAME” and
“USE SAVE TO END”, alternatively.
5. Use the keypad to input the first character of the name.
The number and letters on each telephone button are
displayed in turn.
6. When the desired character is displayed, you can enter
the next character.
7. If you have to use the same button to enter the next
character, press the ►button to move the curser to
the next position and enter the next character.
8. If you will use a different button to enter the next
character, simply press that button. The cursor will
move to the next position automatically.
9. To insert a space, the ►button to move the cursor to
the right.
10. To re-enter a character, press the ◄button or the
►button to move the curser to the character you wish
to modify.
11. After entering all characters, press the Save button to save this number/name in the
directory.
Using the Keypad to Enter a Name
You can program the name for directory entries and memory buttons using the telephone
keypad. When a telephone button is pressed during programming, a number or character
is displayed alternatively in the following order:
1: ‘()1 2: ABC2 3: DEF3
4: GHI4 5: JKL5 6: MNO6
7: PQRS7 8: TUV8 9: WXYZ9
*: * 0: space 0 #: #
Copying the Caller’s Number and Name to the Directory
When the number and name you wish to store in the
directory is displayed, press the Save button. The 3rd line
of the display indicates “SAVE TO?“.
You can save this caller’s number and name into directory
by pressing the Directory button.
Page 12
#25
480-948-4928
FANSTEL CORP_
USE SAVE TO END
The 3rd line of the display flashes the caller’s name and “USE SAVE TO END”. You can
press the Save button to save the caller’s number and name into directory without any
change.
If you wish to change the name of caller, press the ◄button
to move cursor to the first character you wish to modify.
1. Use the keypad to input the first character of the name.
The number and letters on each telephone button are displayed in turn.
2. When the desired character is displayed, you can enter the next character.
3. If you have to use the same button to enter the next character, press the ►button to
move the curser to the next position and enter the next character.
4. If you will use a different button to enter the next character, simply press that button.
The cursor will move to the next position automatically.
5. To insert a space, press the ►button to move the cursor to the right.
6. To re-enter a character, press the ◄button or the ►button to move the cursor to the
character you wish to modify.
7. After entering all characters, press the Save button to save this number/name in the
directory.
Dialing Telephone Numbers from the Directory
You can search for an entry in the directory when the phone is in use or idle.
1. Press the Directory button and the first entry is displayed.
2. Press the σbutton or the τbutton until the record you want is displayed.
3. You can also press the appropriate keypad button one or more times to reach the first
character of the name for which you are searching. For example, by pressing 5, 5
(two times), the first record with a name starting with “K” is displayed. Press the τ
button and the next Klisting is displayed.
4. To dial the number displayed, lift the handset and press the Dial/Enter button. If you
press the Dial/Enter button without lifting the handset, the speakerphone is activated
automatically before dialing.
5. To leave the directory mode at any time, press the Goodbye button.
Deleting Entries in the Directory
To delete an individual entry in the directory, press the Delete button once when the entry
is displayed. The displayed entry is permanently erased.
To delete all of the entries stored in the directory:
1. Press the Directory button.
2. Press and hold the Delete button for 4 – 5 seconds until “DELETE ALL!” appears. All
entries in the directory are permanently erased.
Page 13
#25
480-948-4928
FANSTEL CORP
#00
ENTER NUMBER>
#00
4809484928
USE SAVE TO END
SAVE TO?
4809484928
ENTER NAME>
USE SAVE TO END
4809484928
SMITH
USE SAVE TO END
Storing a New Number and Name in the Memory Buttons
To store a new number and name in the memory buttons:
1. Press the Save button when the display shows no
caller’s number or name. The “SAVE TO?” prompt
appears on the display.
2. Press the memory button where you wish to store this
telephone number (e.g., M1). The “ENTER
NUMBER>“ prompt appears on the display.
3. Use the keypad to enter the telephone number,
including the long distance prefix that you need to dial this number. Insert a pause or
multiple pauses where required by using the Pause button. Then press the Save
button.
Note: If you need to dial an outside line access code,
do NOT include the outside line access code in the
phone number you entered. The outside line access
code is dialed automatically if you entered it during the “Installation” procedures.
4. The third line of LCD displays “ENTER NAME” and “USE SAVE TO END”,
alternatively
5. Use the keypad to input the first character of the
name. The number and letters on each telephone
button are displayed in turn.
6. When the desired character is displayed, you can
enter the next character.
7. If you have to use the same button to enter the next
character, press the ►button to move the curser to
the next position and enter the next character.
8. If you will use a different button to enter the next
character, simply press that button. The curser will
move to the next position automatically.
9. To insert a space, press the ►button to move the curser to the right.
10. To re-enter a character, press the ◄button or the ►button to move the curser to the
character you wish to modify.
11. After entering all characters, press the Save button to save this number/name to the
memory button.
Copying the Caller’s Number and Name to a Memory Button
When the caller’s number and name you wish to store in a
memory button is displayed during Caller ID review, press
the Save button. The 3rd line of the display indicates
“SAVE TO?”.
Page 14
#25
480-948-4928
FANSTEL CORP
SAVE TO?
#00
ENTER NUMBER>
#00
A73PPPA72PPP9484
928PPPb
SAVE TO?
#25
480-948-4928
FANSTEL CORP _
USE SAVE TO END
You can save this caller’s number and name into a memory
button by pressing the desired memory button (e.g., M1).
The 3rd line of display flashes caller’s name and “USE SAVE
TO END”. You can press the Save button to save the
caller’s number and name into the memory button without
any change.
If you wish to change the name of the caller, press the
◄button to move the cursor to the first character you wish to
modify.
1. Use the keypad to input the first character of the name.
The number and letters on each telephone button are
displayed in turn.
2. When the desired character is displayed, you can enter
the next character.
3. If you have to use the same button to enter the next character, press the ►button to
move the curser to the next position and enter the next character.
4. If you will use a different button to enter the next character, simply press that button.
The cursor will move to the next position automatically.
5. To insert a space, press the ►button to move cursor to the right.
6. To re-enter a character, press the ◄button or the ►button to move the cursor to the
character you wish to modify.
7. After entering all characters, press the Save button to save this number/name in the
memory button.
Programming for One-Touch Call Forwarding
If you subscribe to call forwarding services from your
local telephone company, you can program a memory
button to forward incoming calls to another number by
pressing the Call Forward On button once.
1. Press the Save button when the display shows no
caller’s number or name. The “SAVE TO?” prompt
appears on the display.
2. Press the M1 button. The “ENTER NUMBER>“
prompt appears on the display.
3. Use the keypad to enter *73 to deactivate call
forwarding to another number if any. (Note: *is
displayed as Aon the screen.)
4. We suggest entering 3 pauses (P) before entering
Call Forwarding activation code *72. Next, enter 3
pauses (P) before entering the call forwarded
number.
5. We suggest entering 3 pauses (P) before entering Goodbye (b).
Page 15
PPP9484928PPPb
TO MOBILE
6. Press the Save button.
7. You can enter a name for this forward to number,
e.g., “TO MOBILE”.
8. Press the Save button to save this dialing sequence
into the M1 button.
9. Remove the clear plastic cover for memory buttons and write “Call Forward On” next
to M1 button.
When you have to leave your home or your office in a hurry, press the Call Forward On
button once. This will activate the speakerphone, dial the entire call forwarding sequence,
and deactivate the speakerphone automatically.
Follow the above procedures, program M2 (Call Forward Off) button with access code
*73PPb. Press this button once to deactivate call forwarding.
Page 16
10:30am 8/11 #20
480-948-4928
10:30am 8/16 #60
480-948-4928
FANSTEL CORP
10:30am 8/16
25
NEW CALLERS
Caller ID
Caller ID Service and Call Waiting Caller ID Service
The "caller identification" service (Caller ID) allows the caller’s phone number and/or name
to be shown on the display as the call comes in before you pick up the phone. In order to
use this feature, YOU MUST FIRST SUBSCRIBE TO THE CALLER ID SERVICE
provided by your local telephone company. The name of this service may vary depending
on your telephone company. Before using this feature, please make sure you have
properly entered your area code as explained in the “Programming Your Area Code” step
of the Introduction section of this manual.
Important Note: When a new call comes in, you must let your phone ring at least 2 full
times in order for the Caller ID information to be displayed.
The Call Waiting Caller ID service allows the phone number and/or name of a waiting
caller to be shown during a telephone conversation. To use this feature, YOU MUST
FIRST SUBSCRIBE TO CALL WAITING CALLER ID SERVICE with your local telephone
company. The name of this service may vary depending on your telephone company.
Caller ID Display
When you receive a call, the phone number appears on
the display with the day and time the call was received
and is then stored in the Call Memory as shown.
If your Caller ID service includes the caller's name, then
the caller’s name also appears on the display (up to 15
letters) as shown.
The date and time information is received from your
telephone company. If the call came from a different
time zone, it will still show the time in your area. There is a synchronized real-time clock
on the display when the telephone is not in use.
The total number of calls that are saved in the Call Memory is displayed after the “#”
symbol when a call is received. Each call is assigned a call number. The most recent call
has the highest number (e.g. “#99”) and the oldest call has the smallest number (e.g. “
#1”). The phone number of a waiting caller is also registered into the Call Memory as
another call.
New Calls and Total Calls
When the phone is not in use, the display indicates the
number of new calls that have been received since the
last review of the Call Memory as well as the total
number of calls in memory.
Page 17
#80
END OF RECORD
#61
DELETED
Viewing the Caller ID List
This Caller ID telephone automatically stores in the Call
Memory the Caller ID information of the last 99 calls
received. It keeps track of all calls received, whether
they were answered or not. The oldest call in the Call
Memory is always call #1. The highest numbered call (or
call #99 if the Call Memory is full) is always the most recent call. If the Call Memory is full
with 99 calls and a new call comes in, the oldest call, call #1, is automatically deleted to
make room in the memory for the new call.
1. Press the τbutton to display the most recent call and to move backward through the
call records.
Press the σbutton to display the oldest call and to move forward through the call
records.
2. When you get to the last call stored in the Call Memory, then the “END OF
RECORD”message will appear on the display. If the screen indicates "END OF
RECORD", press the σbutton and the screen will display the first record in the Call
Memory. If you press the τbutton, the screen will display the last record in the Call
Memory.
Important Note: The telephone's buttons will not work while the phone is ringing, or for a
few seconds afterward.
Calling Back a Number From the Caller ID List
To easily call back a number from the Caller ID list:
1. Press the σbutton or the τbutton until the number you want to call is displayed.
2. Press the Dial/Enter button. The number is dialed automatically.
The area code is not dialed when it matches the area code stored for 7 DIGITS DIAL. The
area code is dialed for all other numbers. When the area code matches any area code
stored for 10 DIGITS DIAL, then the number is dialed as a ten-digit call (e.g., 303-555-
1212). When the area code does not match an area code for 10 DIGITS DIAL, the number
is dialed as a long distance call (e.g., 1-520-555-1234).
Deleting a Call From the Caller ID List
Important Note: Be sure to write down on a piece of paper any important phone numbers
or information before deleting them from the Call Memory.
1. Press the σbutton or the τbutton until the call
information you want to erase is displayed on the
screen.
2. Press the Delete button once and the selected call is
erased from the Call Memory. The display shows
This manual suits for next models
2
Table of contents
Other Fanstel Telephone manuals
