Fast Mover FMT7560 Specification sheet

Product Instruction Manual
FMT7560
Dent Tool Kit
T: [phone] F: [phone] E: [email protected]
DENT TOOL KIT
ORIGINAL INSTRUCTION
Read the operating manual thoroughly before work and keep it
for future reference.
Read the operating manual thoroughly before work and keep it for future reference.
FMT7560 Manual.indd 1 21/09/2017 16:06

INCLUDES:
1pc glue gun (220-240V~, 50Hz, 40W)
1pc sliding hammer to pull out hard dents
 1pcdentlifter(Babyfaceminilifterornormalminilifter)forslightdentsonatsurface
1pc glue remover
1pc scraper for gentle removal of dent pads
8pcs black glue sticks (11 x 200mm) with very good performance for best results
19pcs glue tabs in various sizes and shapes
OPERATION AND USE OF DENT TOOL KIT
Step 1:
Identifying the vehicle collision /dent. Clean the surface of the paintwork. Use only mild
cleaning agents. The use of a surface coarse sponge will cause irreparable damage.
Step 2:
Use the glue gun, push the glue stick into the back of the glue gun.
Heating the glue gun causes the glue stick to melt.
Step 3:
Use the hot glue gun, put glue on the glue tab, and then place the recess in the dent glue tab.
Step 4 :
Use the T bar slide hammer or dent mini lifter extraction of the bump. What tool you use, also
depends on the size of the dent; Up to 30mm diameter use the dent mini lifter, if larger then use
the slide hammer
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
INCLUDES:
1pc glue gun(220-240V~, 50Hz, 40W)
1pc sliding hammer to pull out hard dents
1pc dent lifter (Baby face mini lifter or normal mini lifter) for slight dents on flat surface
1pc glue remover
1pc scraper for gentle removal of dent pads
8pcs black glue sticks (11 x 200mm) with very good performance for best results
19pcs glue tabs in various sizes and shapes
OPERATION AND USE OF ARTICLE
Step1:
The first position in the vehicle collision / dent. Clean the surface of the process. Use only mild
cleaning agents.The use of surface coarse sponge, will cause irreparable damage.
Step2:
Use the glue gun, push the glue stick into the back of the glue gun . Heating the glue gun and
the glue stick melt.
Step3:
Use hot glue gun, put glue on the glue tab, and then place the recess in the dent glue tab.
Step4:
use the T bar slide hammer or dent mini lifter extraction of the bump.what tool you use, also
depends on the size of the dent, up to 30mm diameter is the dent mini lifter,Other use the slide
hammer.
INCLUDES:
1pc glue gun(220-240V~, 50Hz, 40W)
1pc sliding hammer to pull out hard dents
1pc dent lifter (Baby face mini lifter or normal mini lifter) for slight dents on flat surface
1pc glue remover
1pc scraper for gentle removal of dent pads
8pcs black glue sticks (11 x 200mm) with very good performance for best results
19pcs glue tabs in various sizes and shapes
OPERATION AND USE OF ARTICLE
Step1:
The first position in the vehicle collision / dent. Clean the surface of the process. Use only mild
cleaning agents.The use of surface coarse sponge, will cause irreparable damage.
Step2:
Use the glue gun, push the glue stick into the back of the glue gun . Heating the glue gun and
the glue stick melt.
Step3:
Use hot glue gun, put glue on the glue tab, and then place the recess in the dent glue tab.
Step4:
use the T bar slide hammer or dent mini lifter extraction of the bump.what tool you use, also
depends on the size of the dent, up to 30mm diameter is the dent mini lifter,Other use the slide
hammer.
INCLUDES:
1pc glue gun(220-240V~, 50Hz, 40W)
1pc sliding hammer to pull out hard dents
1pc dent lifter (Baby face mini lifter or normal mini lifter) for slight dents on flat surface
1pc glue remover
1pc scraper for gentle removal of dent pads
8pcs black glue sticks (11 x 200mm) with very good performance for best results
19pcs glue tabs in various sizes and shapes
OPERATION AND USE OF ARTICLE
Step1:
The first position in the vehicle collision / dent. Clean the surface of the process. Use only mild
cleaning agents.The use of surface coarse sponge, will cause irreparable damage.
Step2:
Use the glue gun, push the glue stick into the back of the glue gun . Heating the glue gun and
the glue stick melt.
Step3:
Use hot glue gun, put glue on the glue tab, and then place the recess in the dent glue tab.
Step4:
use the T bar slide hammer or dent mini lifter extraction of the bump.what tool you use, also
depends on the size of the dent, up to 30mm diameter is the dent mini lifter,Other use the slide
hammer.
FMT7560 Manual.indd 2 21/09/2017 16:06

Step 5:
When the temperature reaches the correct time, do not use too much force.
Pull until the glue tab is removed.
Step 6:
Use the release agent to dissolve glue. Use the scraper to remove the glue.
Step 7:
Finally, using a soft clean cloth wipe away any residual glue, restoring the paintwork to
the original condition.
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
Step5:
When the temperature reaches the right time, do not be too hard. Then pull until the glue tab is
removed.
Step6:
Use the release agent , dissolve glue. Use of the scraper, remove the glue.
Step7:
Finally, use a soft clean cloth wipe again residual glue, make the body to restore new look.
Step5:
When the temperature reaches the right time, do not be too hard. Then pull until the glue tab is
removed.
Step6:
Use the release agent , dissolve glue. Use of the scraper, remove the glue.
Step7:
Finally, use a soft clean cloth wipe again residual glue, make the body to restore new look.
Step5:
When the temperature reaches the right time, do not be too hard. Then pull until the glue tab is
removed.
Step6:
Use the release agent , dissolve glue. Use of the scraper, remove the glue.
Step7:
Finally, use a soft clean cloth wipe again residual glue, make the body to restore new look.
FMT7560 Manual.indd 3 21/09/2017 16:06

Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
ELECTRICAL INFORMATION
Warning
Mains plug replacement (UK & Ireland only)
Ifyouneedtoreplacethettedplugofthetool,thenfollowtheinstructionsbelow.
Machines that are connected direct to mains supply.
Machines that are double insulated do not require a connection to earth.
Ifindoubtconsultaqualiedelectrician.
The wires are coloured as follows:
Blue Neutral (N)
Brown Live (L)
3 amp BS 1363A Fuse
Always secure the wires in the plug terminals carefully to make sure that no loose strands are
leftexposedastheycanshortcircuitandcauseinjury,reand/ordamagedthetool.
Securethecableinthecordgriprmly.
Never use a light socket. Never connect the live (L) or neutral (N) wires to the earth pin marked (E).
NOTE: Ifyourmainswiresdifferfromtheaboveconsultaqualiedelectrician.Alwaysmake
sure the mains supply is of the correct voltage and that you use the correct fuse protection.
Regularly inspect all machines, electrical connections and wiring condition for damage. Any
faultsdetectedshouldbeimmediatelyrectiedbeforefurtheruseofthemachine.Alwayshave
thewiringcheckedbyaqualiedelectrician.
In use ensure all wiring and extension cords are kept clear of any cutting tools, sharp objects
andanyotherworkshophazardssuchaswetoors,chemicals,solventsetc.
This machine is protected by a 3 amp fuse make sure the correct fuse is used.
Topreventreorshockhazardsdonotexposetheseproductstorainormoisture.
ELECTRICAL INFORMATION
Warning
Mains plug replacement (UK & Ireland only)
If you need to replace the fitted plug of the tool, then follow the instructions below.
Machines that are connected direct to mains supply.
For machines that are double insulated, do not require a connection to earth.
If in doubt consult a qualified electrician
The wires are coloured as follows
Blue Neutral (N)
Brown Live (L)
3amp BS 1363A Fuse
Always secure the wires in the plug terminals carefully make sure no loose strands are left
exposed as they can short circuit and cause injury, fire and or damaged the tool.
Secure the cable in the cord grip firmly.
Never use a light socket. Never connect the live (L) or neutral (N) wires to the earth pin marked
(E).
NOTE: If your mains wires differ from the above consult a qualified electrician. Always make
sure the mains supply is of correct voltage and you use the correct fuse protection.
Regularly inspect all machines electrical connection and wiring condition for damage. Any
faults detected should be immediately rectified before further use of the machine. Always have
the wiring checked by a qualified electrician.
In use ensure all wiring and extension cords are kept clear of any cutting tools, sharp objects
and any other workshop hazards such as wet floors, chemicals, solvents etc.
This machine is protected by a 3 amp fuse make sure the correct fuse is used.
To prevent fire or shock hazards do not expose these products to rain or moisture.
FMT7560 Manual.indd 4 21/09/2017 16:06

Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
FMT7560 Manual.indd 5 21/09/2017 16:06

Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [email protected]
W: www.fastmovertoolsuk.com
FMT3006
Instrucon Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
W: www.fastmovertoolsuk.com
Please look after the environment, dispose of all packaging in a responsible way.
Always dispose of tools in accordance with local authority guidelines.
© 2014 Fast Mover Tools Ltd. This document is copyright and is not to be copied, circulated, distributed or shown
to anyone other than the intended recipient without the express permission of the directors.
Warranty
We hope that you will be very happy with your purchase. If you do have a problem with your tool, you have the
added peace of mind of a 6 month warranty, which comes into date from the date of purchase (proof of purchase
required).
Scope of Warranty
- The warranty will cover you from all faults cause by defective components or poor workmanship.
- Tools sent outside the EU are not covered by this warranty.
- Product must be returned to us, the warranty does not cover cost of carriage.
- If the product is no longer in manufacture, it will be replaced with a tool of equivalent or higher specification.
What is not covered
- Normal wear and tear caused by use in accordance with the operating instructions.
- Replacement of any provided accessories, such as Backing Pads, Airline Connections, Air Fittings, Blades,
Spanners, etc.
- Accidental damage, faults caused by negligent use or care, neglect, misuse or careless operation, handling and
storage of the product.
- Modification of, or change of, any part of this product in any way.
- Faults caused by use of non compatible accessories.
- Tool seizure caused by insufficient oiling.
- Faults caused by incorrect installation.
- Repairs or alterations carried out by non-approved parties.
- Traced of water or rust inside tool - this shows that a properly working air filter has not been used.
Validity
- This warranty is valid for 6 months after date of purchase.
- Warranty is rendered invalid if;
- Tool is taken apart for any reason without our consent.
- Tool is not maintained daily.
- Air supply line is not used with a properly working air filter.
FMT3006_Product Instructions 19/09/2014 11:23 Page 8
FMT3006
Instrucon Manual
Fast Mover Tools Limited
T: 01582 661993 F: 01582 667100 E: [e-mail]
W: www.fastmovertoolsuk.com
Please look after the environment, dispose of all packaging in a responsible way.
Always dispose of tools in accordance with local authority guidelines.
© 2014 Fast Mover Tools Ltd. This document is copyright and is not to be copied, circulated, distributed or shown
to anyone other than the intended recipient without the express permission of the directors.
Warranty
We hope that you will be very happy with your purchase. If you do have a problem with your tool, you have the
added peace of mind of a 6 month warranty, which comes into date from the date of purchase (proof of purchase
required).
Scope of Warranty
- The warranty will cover you from all faults cause by defective components or poor workmanship.
- Tools sent outside the EU are not covered by this warranty.
- Product must be returned to us, the warranty does not cover cost of carriage.
- If the product is no longer in manufacture, it will be replaced with a tool of equivalent or higher specification.
What is not covered
- Normal wear and tear caused by use in accordance with the operating instructions.
- Replacement of any provided accessories, such as Backing Pads, Airline Connections, Air Fittings, Blades,
Spanners, etc.
- Accidental damage, faults caused by negligent use or care, neglect, misuse or careless operation, handling and
storage of the product.
- Modification of, or change of, any part of this product in any way.
- Faults caused by use of non compatible accessories.
- Tool seizure caused by insufficient oiling.
- Faults caused by incorrect installation.
- Repairs or alterations carried out by non-approved parties.
- Traced of water or rust inside tool - this shows that a properly working air filter has not been used.
Validity
- This warranty is valid for 6 months after date of purchase.
- Warranty is rendered invalid if;
- Tool is taken apart for any reason without our consent.
- Tool is not maintained daily.
- Air supply line is not used with a properly working air filter.
FMT3006_Product Instructions 19/09/2014 11:23 Page 8
Warranty
We hope that you will be very happy with your purchase. If you do have a problem with your tool, you have the
added peace of mind of a 12 month warranty, which comes into date from the date of purchase (proof of purchase
required).
Scope of Warranty
- The warranty will cover you from all faults cause by defective components or poor workmanship.
- Tools sent outside the EU are not covered by this warranty.
- Product must be returned to us, the warranty does not cover cost of carriage.
- If the product is no longer in manufacture, it will be replaced with a tool of equivalent or higher specification.
What is not covered
- Normal wear and tear caused by use in accordance with the operating instructions.
- Accidental damage, faults caused by negligent use or care, neglect, misuse or careless operation,
handling and storage of the product.
- Modification of, or change of, any part of this product in any way.
- Faults caused by use of non compatible accessories.
- Faults caused by incorrect installation.
- Repairs or alterations carried out by non-approved parties.
Validity
- This warranty is valid for 12 months after date of purchase.
- Warranty is rendered invalid if;
- Tool is taken apart for any reason without our consent.
- Tool is not maintained daily.
- Air supply line is not used with a properly working air filter.
Please look after the environment, dispose of all packaging in a responsible way.
Always dispose of tools in accordance with local authority guidelines.
© 2015 Fast Mover Tools Ltd. This document is copyright and is not to be copied, circulated, distributed or shown
to anyone other than the intended recipient without the express permission of the directors.
FMT7560 Manual.indd 6 21/09/2017 16:06