Fath Mechatronics TANlock User manual

TANlock
Assembly instructions
08.08.2018 1

① 1 x TANlock
② 1 x Cover cap - long
③ 1 x Cover cap - short
④ 2 x Cylinder head screw DIN7985 M4x25c
⑤ 2 x Cylinder head screw DIN7985 M4x18
⑥ 1 x Hexagon screw mit Verzahnung M6x8
⑦ 1 x Cam lock housing
08.08.2018 2
②
③
④
⑤
⑦
①
Package contents
⑥

1. Open the packaging, pull on the plastic tab and remove the TANlock.
08.08.2018 3
2. Pull out the inner carton and open the side door to take out the assembly kit.
Unpacking

08.08.2018 4
3. Loosen the retaining plate slightly. 4. Hang the TANlock into the
door cut-out and press the
mandrel into the existing
locking mechanism.
Assembly

5. Insert the enclosed cylinder head screws for your cabinet
through the locking mechanism into the TANlock and screw
them tight.
08.08.2018 5
6. Fasten the retaining plate.
Assembly
If you have a
lever lock,
continue.
If you have a
bar lock,
go to point 8.

08.08.2018 6
Assembly
7. If you use a lever lock, place the cam lock housing on the mandrel of the TANlock and screw it down with the enclosed
M4x18 cylinder head screws ⑤.

08.08.2018 7
8. Fasten the fitting cover cap to your cabinet at the TANlock. Hook the cover cap at the top and click the cap at the
bottom into the retaining plate.
Assembly

08.08.2018 8
Assembly
9. Connect the TANlock via Power over Ethernet (PoE) or with the serial cable over PC/powerbank. The TANlock is
now lockable and unlockable with the standard code: 123412
PoE Serial cable

TANlock
Installation-Guide
08.08.2018 9

Connect via serial cable
1. Download the »TANlock Explorer«at the following link:
08.08.2018 10
First Steps
2. Connect your TANlock to your PC.
You have two options:
Connect via ethernet cable
https://crm.fath-mechatronics.de/~sXd8o
pay attention to firewall release!
•The TANlock may not yet be
implemented in the corporate
network because the TANlock is
delivered with a fixed IP-address
•Connect via PoE-Injector
or PoE-Switch
Pay attention to the correct
driver for the serial cable!
Never connect
both at the
same time!
Download the driver here:
http://www.ftdichip.com/Drivers/C
DM/CDM%20v2.12.28%20WHQ
L%20Certified.zip

1. Connect your TANlock to the ethernet cable and your PC.
2. Open your Windows Settings.
3. Continue to Network & Internet.
08.08.2018 11
4. Click with the mouse on the "blue" deposited "Ethernet" port.
Network Settings
in conjunction with ethernet

5. The window "Ethernet Status" opens, see picture 1.
6. Click on the button "Properties" - button, see
picture 1.
7. Click the "Internet Protocol, Version 4 (TCP/IPv4)"
box and click "Properties", see picture 2.
08.08.2018 12
Picture ①Picture ②
Network Settings
in conjunction with ethernet

08.08.2018 13
8. The window "Internet Protocol, Version 4 (TCP/IPv4) "
opens, see picture 3.
9. Takeover the specified IP-address / Subnet mask, as
shown in picture 3.
10. Acceot the setting with the "OK" button and close
all the opened windows.
Now you can connect to the TANlock via TANlock-Explorer.
Follow the instructions on page 15.
Network Settings
in conjunction with ethernet
Picture ③

08.08.2018 14
Connect via serial cable
1. Download and install the appropriate driver at the following link:
http://www.ftdichip.com/Drivers/CDM/CDM%20v2.12.28%20WHQL%20Certified.zip
2. Connect your TANlock via serial cable to your PC.

1. Open the TANlock-Explorer.
08.08.2018 15
TANlock – Configuration
via TANlock-Explorer
Option 1: Ethernet cable Option 2: Serial cable
Select one of the two options and continue with "Connect"

08.08.2018 16
TANlock – Configuration
via TANlock-Explorer
2. Right-click on the word TANlock and select "Launch
Cockpit", see picture 1.
3. It opens a password window. Enter the password
"91174" here, see picture 2.
4. Confirm the next window with "OK".
5. The configuration window opens, see picture 3.
6. In the "Network" tab you can now change your IP
settings. You must confirm all changes with "Save" and
conclude by right clicking on the word TANlock with
"Reset" (see picture1).
Bild ①
Bild ②
Bild ③

08.08.2018 17
TANlock
Access to the TANlock via internet browser
1. Open your internet browser and enter the IP-
address of your TANlock as follows:
<ip-address>/lab/info
The delivery status is: 192.168.0.90
Here you can see the current state of your TANlock.

08.08.2018 18
TANlock
Access to the TANlock via internet browser
2. With the input command you are able to open
your TANlock remotely.
Enter the command as follows:
<ip-address>/lab/input/123412
In the delivery state the code is: 123412

08.08.2018 19
TANlock
Access to the TANlock via internet browser
2. The help command gives you an overview of
all browser options.
Enter the command as follows:
<ip-address>/help

08.08.2018 20
Finish!