Fayat Group DYNAPAC CC1300 Instructions for use

Instruction manualInstruction manual
Operating & MaintenanceOperating & Maintenance
4812162001_D.pdf4812162001_D.pdf
Vibratory rollerVibratory roller
CC1300CC1300
EngineEngine
Kubota D1803-CR-TE4B (T4f)Kubota D1803-CR-TE4B (T4f)
Kubota D1803-CR-TE5B (Stage V) Kubota D1803-CR-TE5B (Stage V)
Serial numberSerial number
10000374xxA016841 - A03081010000374xxA016841 - A030810
10000450xxA026088 - A03058010000450xxA026088 - A030580
Translation of original instructionTranslation of original instruction
Reservation for changesReservation for changes
Printed in SwedenPrinted in Sweden

2000h-Maintenance
4812162001_D.pdf2021-12-14
Table of Contents
Introduction .............................................................................................................................. 1
The machine ............................................................................................... 1
Intended use ............................................................................................... 1
Signal symbols and meaning ...................................................................... 1
Safety information ....................................................................................... 1
General ....................................................................................................... 2
CE marking and Declaration of conformity.................................................. 3
Safety - General instructions.................................................................................................... 5
Safety - when operating ........................................................................................................... 7
Work driving ................................................................................................ 7
Driving near edges ...................................................................................... 8
Special instructions .................................................................................................................. 9
Standard lubricants and other recommended oils and fluids ...................... 9
Higher ambient temperatures, above +40°C (104°F).................................. 9
Lower ambient temperature - Freeze risk ................................................... 9
Temperatures.............................................................................................. 9
high pressure cleaning ................................................................................ 9
Fire fighting ............................................................................................... 10
Roll Over Protective Structure (ROPS) ..................................................... 10
Battery handling ........................................................................................ 10
Jump starting............................................................................................. 11
Technical specifications ......................................................................................................... 13
Vibrations - Operator station ..................................................................... 13
Noise level................................................................................................. 13
Slopes ....................................................................................................... 13
Dimensions, top view ................................................................................ 14
Dimensions, side view............................................................................... 15
Weights and volumes................................................................................ 16
Working capacity....................................................................................... 16
General ..................................................................................................... 16

2000h-Maintenance
4812162001_D.pdf 2021-12-14
CO2-emission............................................................................................ 17
Tightening torque ...................................................................................... 18
ROPS - bolts ............................................................................................. 19
Hydraulic system....................................................................................... 19
Machine description ............................................................................................................... 21
Diesel engine ............................................................................................ 21
Electrical system ....................................................................................... 21
Propulsion system/Transmission .............................................................. 21
Brake system ............................................................................................ 21
Steering system ........................................................................................ 21
ROPS ........................................................................................................ 21
Identification ............................................................................................................ 22
Product identification number on the frame .............................................. 22
Explanation of 17PIN serial number.......................................................... 22
Machine plate............................................................................................ 23
Engine plates ............................................................................................ 23
Location - decals ....................................................................................... 25
Location - decals, CALIFORNIA ............................................................... 27
Safety decals............................................................................................. 27
Info decals................................................................................................. 30
Instruments/Controls ............................................................................................... 31
Locations - Instruments and controls ........................................................ 31
Locations - Control panel and controls...................................................... 32
Function description .................................................................................. 33
Electrical system...................................................................................................... 36
Fuses on machine equipped with Sauer-Danfoss ECU ............................ 36
Fuses on machine equipped with HY-TTC 71 ECU.................................. 37
Fuses at battery master disconnect switch ............................................... 38
Relays ....................................................................................................... 38
Operation ............................................................................................................................... 39

2000h-Maintenance
4812162001_D.pdf2021-12-14
Before starting ......................................................................................................... 39
Master switch - Switching on..................................................................... 39
Driver seat (Std) - Adjustment................................................................... 39
Driver seat (Option) - Adjustment.............................................................. 40
Parking brake - Check............................................................................... 40
Instruments and lamps - Checking............................................................ 41
Interlock..................................................................................................... 42
Operator position....................................................................................... 43
Starting .................................................................................................................... 44
Starting the engine .................................................................................... 44
Driving ..................................................................................................................... 45
Operating the roller ................................................................................... 45
Interlock/Emergency stop/Parking brake - Check ..................................... 46
Regeneration of DPF filter......................................................................... 46
Vibration .................................................................................................................. 48
Manual/Automatic vibration....................................................................... 48
Braking .................................................................................................................... 49
Normal braking.......................................................................................... 49
Emergency braking ................................................................................... 49
Switching off.............................................................................................. 50
Parking .................................................................................................................... 50
Chocking the drums .................................................................................. 50
Battery disconnector ................................................................................. 51
Long-term parking.................................................................................................................. 53
Engine ....................................................................................................... 53
Battery....................................................................................................... 53
Air cleaner, exhaust pipe........................................................................... 53
Fuel tank ................................................................................................... 53
Hydraulic reservoir .................................................................................... 53
Water tank................................................................................................. 53

2000h-Maintenance
4812162001_D.pdf 2021-12-14
Steering cylinder, hinges, etc. ................................................................... 54
Hoods, tarpaulin ........................................................................................ 54
Miscellaneous ........................................................................................................................ 55
Lifting ....................................................................................................................... 55
Locking the articulation ............................................................................. 55
Lifting the roller.......................................................................................... 55
Unlocking the articulation .......................................................................... 56
Towing/Recovering.................................................................................................. 56
Short distance towing with switched off engine......................................... 56
Release the brakes ................................................................................... 57
Towing the roller........................................................................................ 58
Transport ................................................................................................................. 58
Securing CC1300 for loading .................................................................... 59
Retractable ROPS (Optional).................................................................... 60
Operating instructions - Summary ......................................................................................... 63
Preventive maintenance ........................................................................................................ 65
Acceptance and delivery inspection.......................................................... 65
Warranty.................................................................................................... 65
Maintenance - Lubricants and symbols ................................................................................. 67
Maintenance symbols ............................................................................... 68
Maintenance - Maintenance schedule ................................................................................... 69
Service and maintenance points ............................................................... 69
General ..................................................................................................... 70
Every 10 hours of operation (Daily)........................................................... 70
After the FIRST 50 hours of operation ...................................................... 71
Every 50 hours of operation (Weekly)....................................................... 71
Every 250 / 750 / 1250 / 1750 hours of operation ..................................... 71
Every 500 / 1500 hours of operation ......................................................... 72
Every 1000 hours of operation .................................................................. 73
Every 2000 hours of operation .................................................................. 74

2000h-Maintenance
4812162001_D.pdf2021-12-14
Service - Checklist................................................................................................... 75
Maintenance, 10h .................................................................................................................. 77
Check - Coolant system ............................................................................ 77
Coolers
Checking - Cleaning.................................................................................. 78
Hydraulic reservoir, Level check - Filling................................................... 79
Lowering of engine hood........................................................................... 80
Air circulation - Check ............................................................................... 80
Fuel tank - Filling....................................................................................... 81
Water tank - Filling .................................................................................... 81
Sprinkler system/Drum
Checking - Cleaning.................................................................................. 82
Scrapers, fixed
Checking - Setting..................................................................................... 83
Scrapers, spring-action (Optional)
Checking - Adjustment .............................................................................. 83
Sprinkler system/Drum
Cleaning of sprinkler nozzle ...................................................................... 84
Brakes - Check.......................................................................................... 85
Maintenance - 50h ................................................................................................................. 87
Air cleaner indicator .................................................................................. 87
Air cleaner
Check - Replacement of main filter ........................................................... 87
Air filter indicator - Resetting ..................................................................... 88
Backup filter - Change............................................................................... 88
Air cleaner
- Cleaning.................................................................................................. 89
Steering cylinder and steering joint - Lubrication ...................................... 89
Pre-fuel filter - Draining ............................................................................. 90
Maintenance measures - 250 h ............................................................................................. 91
Battery
- Check condition ...................................................................................... 91
Engine oil and oil filter - Change ............................................................... 92

2000h-Maintenance
4812162001_D.pdf 2021-12-14
Coolers
Checking - Cleaning.................................................................................. 93
Maintenance measures - 500 h ............................................................................................. 95
Battery
- Check condition ...................................................................................... 95
Engine oil and oil filter - Change ............................................................... 96
Drum - oil level
Inspection - filling ...................................................................................... 97
Rubber elements and attachment screws
Check ........................................................................................................ 97
Controls - Lubrication ................................................................................ 98
Hydraulic reservoir cap - Check ................................................................ 98
Controls - Lubrication ................................................................................ 99
Check - Coolant system ............................................................................ 99
Replacing the fuel filter............................................................................ 100
Replacing the pre-filter ............................................................................ 101
Replacing the diesel engine’s oil separator filter..................................... 102
Maintenance - 1000h ........................................................................................................... 103
Battery
- Check condition .................................................................................... 103
Engine oil and oil filter - Change ............................................................. 104
Drum - oil level
Inspection - filling .................................................................................... 105
Rubber elements and attachment screws
Check ...................................................................................................... 105
Controls - Lubrication .............................................................................. 106
Hydraulic reservoir cap - Check .............................................................. 106
Controls - Lubrication .............................................................................. 107
Check - Coolant system .......................................................................... 107
Replacing the fuel filter............................................................................ 108
Replacing the pre-filter ............................................................................ 109
Hydraulic fluid reservoir - Draining .......................................................... 109

2000h-Maintenance
4812162001_D.pdf2021-12-14
Replacing the hydraulic oil filter .............................................................. 110
Maintenance - 2000h ........................................................................................................... 113
Battery
- Check condition .................................................................................... 113
Engine oil and oil filter - Change ............................................................. 114
Drum - oil level
Inspection - filling .................................................................................... 115
Rubber elements and attachment screws
Check ...................................................................................................... 115
Controls - Lubrication .............................................................................. 116
Hydraulic reservoir cap - Check .............................................................. 116
Controls - Lubrication .............................................................................. 117
Check - Coolant system .......................................................................... 117
Replacing the hydraulic oil filter .............................................................. 118
Hydraulic fluid reservoir - Draining .......................................................... 119
Hydraulic tank - Changing the fluid ......................................................... 120
Replacing the pre-filter ............................................................................ 121
Replacing the fuel filter............................................................................ 122
Drum - Oil change ................................................................................... 122
Water tank - Draining .............................................................................. 123
Water pump - Draining ............................................................................ 123
Fuel tank - Cleaning ................................................................................ 124
Water tank - Cleaning ............................................................................. 124
Steering joint - Check.............................................................................. 125

2000h-Maintenance
4812162001_D.pdf 2021-12-14

Introduction
4812162001_D.pdf2021-12-14
Introduction
The machine
Dynapac CC1300 is a self-propelled vibratory tandem
roller in the 4 metric tonnes class featuring 1300 mm
wide drums. The machine is equipped with drive,
brakes, and vibration on both drums.
Intended use
CC1300 has primarily been designed for the
compaction of asphalt, but has excellent compaction
capacity for reinforcement layers and bearing courses.
The roller is mainly intended for compacting asphalt on
streets and minor roads in towns. It has sufficient
capacity to follow a small asphalt paver.
Signal symbols and meaning
WARNING ! Indicates potential hazardous
situation/procedure which, if not avoided, could
result in death or serious injury.
WARNING ! Indicates potential hazardous
situation/procedure which, if not avoided, could
result in death or serious injury.
CAUTION ! Indicates potential hazardous
situation/procedure which, if not avoided, could
result in minor or moderate injury, damage to
the machine or property.
CAUTION ! Indicates potential hazardous
situation/procedure which, if not avoided, could
result in minor or moderate injury, damage to
the machine or property.
Safety information
It is recommended to at least train operators in
handling and daily maintenance of the machine
in accordance with the instruction manual.
It is recommended to at least train operators in
handling and daily maintenance of the machine
in accordance with the instruction manual.
Passengers are not allowed on the machine, and
you must sit in the seat when operating the
machine.
Passengers are not allowed on the machine, and
you must sit in the seat when operating the
machine.
The safety manual supplied with the machine
must be read by all roller operators. Always
follow the safety instructions. Do not remove
the manual from the machine.
The safety manual supplied with the machine
must be read by all roller operators. Always
follow the safety instructions. Do not remove
the manual from the machine.
We recommend that the operator reads the
safety instructions in this manual carefully.
Always follow the safety instructions. Ensure
that this manual is always easily accessible.
We recommend that the operator reads the
safety instructions in this manual carefully.
Always follow the safety instructions. Ensure
that this manual is always easily accessible.
1

Introduction
4812162001_D.pdf 2021-12-14
Read the entire manual before starting the
machine and before carrying out any
maintenance.
Read the entire manual before starting the
machine and before carrying out any
maintenance.
Replace immediately the instruction manuals if
lost, damaged or unreadable.
Replace immediately the instruction manuals if
lost, damaged or unreadable.
Ensure good ventilation (extraction of air by fan)
where the engine is run indoors.
Ensure good ventilation (extraction of air by fan)
where the engine is run indoors.
CALIFORNIA
Decal and location of decal shown in section
Machine description.
Proposition 65
General
This manual contains instructions for machine
operation and maintenance.
The machine must be correctly maintained for
maximal performance.
The machine should be kept clean so that any
leakages, loose bolts and loose connections are
discovered at as early a point in time as possible.
Do not spray with high-pressure cleaner directly onto
gaskets and bearing spacings in steering hitch and
drum, and electronics.
Inspect the machine every day, before starting.
Inspect the entire machine so that any leakages or
other faults are detected.
2

Introduction
4812162001_D.pdf2021-12-14
Check the ground under the machine. Leakages are
more easily detected on the ground than on the
machine itself.
THINK ENVIRONMENT ! Do not release oil,
fuel and other environmentally hazardous
substances into the environment. Always send
used filters, drain oil and fuel remnants to
environmentally correct disposal.
THINK ENVIRONMENT ! Do not release oil,
fuel and other environmentally hazardous
substances into the environment. Always send
used filters, drain oil and fuel remnants to
environmentally correct disposal.
This manual contains instructions for periodic
maintenance, where maintenance after every 10 and
50 hours of operation can be performed by the
machine operator. Other maintenance intervals must
be carried out by accredited (Dynapac) service
personnel.
Additional instructions for the engine can be
found in the manufacturer's engine manual.
Additional instructions for the engine can be
found in the manufacturer's engine manual.
Specific maintenance and checks on diesel
engines must be performed by engine supplier
authorized personnel.
Specific maintenance and checks on diesel
engines must be performed by engine supplier
authorized personnel.
CE marking and Declaration of conformity
(Applies to machines marketed in EU/EEC)
This machine is CE marked. This shows that on
delivery it complies with the basic health and safety
directives applicable for the machine in accordance
with machinery directive 2006/42/EC and that it also
complies with other regulations and directives
applicable for this machine.
A "Declaration of conformity" is supplied with this
machine, which specifies the applicable regulations
and directives with supplements, as well as the
harmonized standards and other regulations that are
applied and according to the regulations must be
declared in writing.
3

Introduction
4812162001_D.pdf 2021-12-14
4

Safety - General instructions
4812162001_D.pdf2021-12-14
Safety - General instructions
(Also read the safety manual)
•The operator must be familiar with the contents of the OPERATION section
before starting the roller.
•The operator must be familiar with the contents of the OPERATION section
before starting the roller.
•Ensure that all instructions in the MAINTENANCE section are followed. •Ensure that all instructions in the MAINTENANCE section are followed.
•Only the operator is allowed to be on the roller. Remain seated at all times
when operating the roller.
•Only the operator is allowed to be on the roller. Remain seated at all times
when operating the roller.
•Never use the roller if it is in need of adjustment or repair. •Never use the roller if it is in need of adjustment or repair.
•Only ascend and descend the roller when it is stationary. Use the intended
footsteps, grips and rails. Always use the three-point grip (both feet and one
hand, or one foot and both hands) when ascending or descending the
machine. Never jump down from the machine.
•Only ascend and descend the roller when it is stationary. Use the intended
footsteps, grips and rails. Always use the three-point grip (both feet and one
hand, or one foot and both hands) when ascending or descending the
machine. Never jump down from the machine.
•Dynapac always recommends mounted ROPS (Roll Over Protective
Structure), or a ROPS-approved cab and seat belt usage.
•Dynapac always recommends mounted ROPS (Roll Over Protective
Structure), or a ROPS-approved cab and seat belt usage.
•Drive slowly in sharp bends. •Drive slowly in sharp bends.
•Avoid driving across slopes. Drive straight up or straight down the slope. •Avoid driving across slopes. Drive straight up or straight down the slope.
•Never operate with the drum outside the edge, the substrate might not have
full bearing strength or the edge is close to a slope. Avoid operating close to
edges and ditches and the like as well as on poor ground conditions that
jeopardizes the bearing strength and capacity to support the roller.
•Never operate with the drum outside the edge, the substrate might not have
full bearing strength or the edge is close to a slope. Avoid operating close to
edges and ditches and the like as well as on poor ground conditions that
jeopardizes the bearing strength and capacity to support the roller.
•Make sure that there are no obstacles in the direction of travel, on the
ground, in front of or behind the roller, or overhead.
•Make sure that there are no obstacles in the direction of travel, on the
ground, in front of or behind the roller, or overhead.
•Drive particularly carefully on uneven ground. •Drive particularly carefully on uneven ground.
•Keep the roller clean. Clean any dirt or grease that accumulates on the
footsteps or operator platform to avoid slipping risk. Keep all signs and
decals clean and legible.
•Keep the roller clean. Clean any dirt or grease that accumulates on the
footsteps or operator platform to avoid slipping risk. Keep all signs and
decals clean and legible.
•Safety measures before refueling:
- Stop the engine
- Do not smoke.
- No naked flames in the vicinity of the roller.
- Earth the filling equipment nozzle by keeping it in contact to the tank
opening to avoid sparks.
•Safety measures before refueling:
- Stop the engine
- Do not smoke.
- No naked flames in the vicinity of the roller.
- Earth the filling equipment nozzle by keeping it in contact to the tank
opening to avoid sparks.
•Before repairs or service:
- Chock the drums/wheels.
- Lock the articulation if necessary.
- Place blocks under overhanging equipment, such as strike-off blade, edge
cutter/compactor and chip spreader.
•Before repairs or service:
- Chock the drums/wheels.
- Lock the articulation if necessary.
- Place blocks under overhanging equipment, such as strike-off blade, edge
cutter/compactor and chip spreader.
5

Safety - General instructions
4812162001_D.pdf 2021-12-14
•Hearing protection is recommended if the noise level exceeds 80 dB(A). The
noise level can vary depending on the equipment on the machine and the
surface the machine is being used on.
•Hearing protection is recommended if the noise level exceeds 80 dB(A). The
noise level can vary depending on the equipment on the machine and the
surface the machine is being used on.
•Modifications to the roller, including the use of any attachment/equipment,
not approved by Dynapac that might compromise safety (including visibility)
are not allowed. Any modifications are only to be made after written approval
has been given by Dynapac.
•Modifications to the roller, including the use of any attachment/equipment,
not approved by Dynapac that might compromise safety (including visibility)
are not allowed. Any modifications are only to be made after written approval
has been given by Dynapac.
•Avoid using the roller before the hydraulic fluid has reached its normal
working temperature. Braking distances can be longer than normal when the
fluid is cold.
•Avoid using the roller before the hydraulic fluid has reached its normal
working temperature. Braking distances can be longer than normal when the
fluid is cold.
•For your own protection always wear:
- working boots with steel toecaps
- ear protectors
- reflecting clothing/high visibility jacket
Also wear:
- helmet if no cab or FOPS, or if required by worksite management
- working gloves if no cab and for work outside operator´s platform.
•For your own protection always wear:
- working boots with steel toecaps
- ear protectors
- reflecting clothing/high visibility jacket
Also wear:
- helmet if no cab or FOPS, or if required by worksite management
- working gloves if no cab and for work outside operator´s platform.
•If the machine seems to be responding abnormally during travel, stop and
check it.
•If the machine seems to be responding abnormally during travel, stop and
check it.
6

Safety - when operating
4812162001_D.pdf2021-12-14
Safety - when operating
Prevent persons from entering or remaining in
the risk zone, i.e. a distance of at least 7 m (23
ft) in all directions from operating machines.
Prevent persons from entering or remaining in
the risk zone, i.e. a distance of at least 7 m (23
ft) in all directions from operating machines.
The operator may allow a person to remain in
the risk zone, however he/she must be attentive
and operate the machine only when the person
is fully visible or has given a clear indication of
where he or she is.
The operator may allow a person to remain in
the risk zone, however he/she must be attentive
and operate the machine only when the person
is fully visible or has given a clear indication of
where he or she is.
Avoid driving across a slope. Drive straight up
and down sloping ground.
Avoid driving across a slope. Drive straight up
and down sloping ground.
Work driving
Dynapac always recommends mounted ROPS
(Roll Over Protective Structure) and seat belt
usage.
Dynapac always recommends mounted ROPS
(Roll Over Protective Structure) and seat belt
usage.
On machines with foldable ROPS, make sure that
the ROPS is correctly mounted in the upright
position during all operation.
On machines with foldable ROPS, make sure that
the ROPS is correctly mounted in the upright
position during all operation.
Avoid operating close to edges and ditches and the
like as well as on poor ground conditions that
jeopardizes the bearing strength and capacity to
support the roller. Pay attention to potential obstacles
above the machine, such as overhead cables and the
branches of trees etc.
Pay particular attention to the stability of the substrate
when compacting close to edges and holes. Do not
compact with a large overlap from the previous track in
order to maintain roller stability. Consider other
compaction methods such as remote-control or a
walk-behind roller close to steep slopes or where the
bearing strength of the substrate is unknown.
7

Safety - when operating
4812162001_D.pdf 2021-12-14
Driving near edges
Never operate with the drum outside the edge, the
substrate might not have full bearing strength or
the edge is close to a slope.
Never operate with the drum outside the edge, the
substrate might not have full bearing strength or
the edge is close to a slope.
Keep in mind that the machine's center of gravity
moves outwards when steering. For example, the
center of gravity moves to the right when you steer
to the left.
Keep in mind that the machine's center of gravity
moves outwards when steering. For example, the
center of gravity moves to the right when you steer
to the left.
8

Special instructions
4812162001_D.pdf2021-12-14
Special instructions
Standard lubricants and other recommended
oils and fluids
Before leaving the factory, the systems and
components are filled with the oils and fluids specified
in the lubricant specification. These are suitable for
ambient temperatures in the range -15°C to +40°C
(5°F - 105°F).
The maximum ambient temperature for
biological hydraulic fluid is +35°C (95°F).
The maximum ambient temperature for
biological hydraulic fluid is +35°C (95°F).
Higher ambient temperatures, above +40°C
(104°F)
For operation of the machine at higher ambient
temperatures, however maximum +50°C (122°F), the
following recommendations apply:
The diesel engine can be run at this temperature using
normal oil. However, the following fluids must be used
for other components:
Hydraulic system - mineral oil Shell Tellus S2V100 or
similar.
Lower ambient temperature - Freeze risk
Make sure that the watering system is empty/drained
of water (sprinkler, hoses, tank/s) or that anti-freeze
has been added, to prevent the system freezing.
Temperatures
The temperature limits apply to standard versions of
rollers.
Rollers equipped with additional equipment, such as
noise suppression, may need to be more carefully
monitored in the higher temperature ranges.
high pressure cleaning
Do not spray water directly onto electrical components
or the instrument panels.
Place a plastic bag over the fuel filler cap and secure
with a rubber band. This is to avoid high pressure
water entering the vent hole in the filler cap. This could
cause malfunctions, such as the blocking of filters.
Do not spray with high-pressure cleaner directly onto
gaskets and bearing spacings in steering hitch and
drum, and electronics.
9

Special instructions
4812162001_D.pdf 2021-12-14
Never aim the water jet directly at the fuel tank
cap, or into exhaust pipe. This is particularly
important when using a high-pressure cleaner.
Never aim the water jet directly at the fuel tank
cap, or into exhaust pipe. This is particularly
important when using a high-pressure cleaner.
Fire fighting
If the machine catches fire, use an ABC-class powder
fire extinguisher.
A BE-class carbon dioxide fire extinguisher can also
be used.
Roll Over Protective Structure (ROPS)
Never carry out any welding or drilling in the
Roll Over Protective Structure (ROPS).
Never carry out any welding or drilling in the
Roll Over Protective Structure (ROPS).
Never repair a damaged ROPS structure, it must
be replaced with a new one.
Never repair a damaged ROPS structure, it must
be replaced with a new one.
Battery handling
When removing batteries, always disconnect the
negative cable first.
When removing batteries, always disconnect the
negative cable first.
When fitting batteries, always connect the
positive cable first.
When fitting batteries, always connect the
positive cable first.
Dispose of old batteries in an environmentally
friendly way. Batteries contain toxic lead.
Dispose of old batteries in an environmentally
friendly way. Batteries contain toxic lead.
Do not use a quick-charger for charging the
battery. This may shorten battery life.
Do not use a quick-charger for charging the
battery. This may shorten battery life.
10