FDS FD102ARM User manual

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 1 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Installation and Operation Manual
FD102ARM
10.2” Widescreen LCD on Arm

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 2 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Table of Contents
General Information............................................................................................3
Front View............................................................................................................3
Additional Information........................................................................................3
Specifications......................................................................................................4
Installation Instructions......................................................................................4
Power...................................................................................................................4
Wiring Suggestions ............................................................................................5
S-Video/Composite and Audio Wiring...............................................................5
VGA Wiring..........................................................................................................6
Mounting & Base Info.........................................................................................6
Power & Ground Wiring......................................................................................7
Power/Video ........................................................................................................7
Operations Instructions......................................................................................8
Button Control.....................................................................................................8
Remote Control Buttons.....................................................................................9
Technical Drawing ............................................................................................10
Technical Support.............................................................................................11
Instructions for Continued Airworthiness......................................................11
Warranty ............................................................................................................12
Log of Revisions...............................................................................................13

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 3 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
General Information
This high resolution 10.2” Widescreen LCD is perfect for cabin video and graphical
entertainment. Built with retrofit aircraft integration in mind, this display can switch
between three video input sources using an infrared remote or the control buttons on the
top of the monitor.
Front View
Additional Information
The articulating arm rotates 180 degrees, tilts forward and aft, and the monitor can turn
180 degrees on the end of the mount.
The FD102ARM can also be connected to existing video switchers and can take a
composite video input from a selector interface box. Multiple input sources can be
selected and displayed on the monitor.
The FD102ARM cabinet is made of all metal components. DO-160 testing has been
completed and is available upon request.
The LCD is protected with a .060” Lexan lens. The purpose of this lens is to prevent
scratching of the LCD.

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 4 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Specifications
Display Size
8.7” (W) x 5.2” (H)
Display Type
10.2” Widescreen TFT Color LCD
Display Color
262,144 Colors
Display Dimension
9.80”(W) x 6.3”(H) x 1.1”(D)
Mount Dimension
7”(W) x 1.8”(H) x 1.5”(D)
Screen Resolution
800x480/640x480~1024x768
Brightness
500 cd/m²
Weight
2 lbs 15 oz
Power
12VDC @ 2 Amps
28VDC @ .5 Amps
PC & Video Input
SVGA (Analog RGB 15 pin D-sub)
2 Composite
Video Input
S-Video, Composite
Video Type Supported
NTSC/PAL
Screen Control
On Screen Display Menu
Remote Control
IR, included
Materials
Aluminum
Operating Temperature (includes
FD102ARM Ver VC5)
0-50° C (32-122° F)
DO-160 Testing
160F, Sec 8, Category R, Test Curve G
Installation Instructions
All cabin entertainment equipment, such as the FD102ARM, should be installed on a non-
essential bus and have a dedicated circuit breaker. It is a requirement that a switch be
installed in the cockpit so that the pilot can de-energize the entertainment system should it
become necessary.
It is recommended that you leave approximately ¼ inch of space around the rear of the
display to have circulating air.
Power
This is a 12VDC monitor that requires 2 Amps of power to operate. This is also available
as FD102ARM (28V) which is a 28VDC monitor that requires .5 Amp of power to operate.
The unit turns on automatically upon power application.

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 5 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Wiring Suggestions
All shields should be grounded to the connector at the source, and floating at the display.
Avoid routing video wiring parallel to:
AC wiring
Strobe wiring
DC motor supply cables
Inverter cabling
Or any other potential noise source.
S-Video/Composite and Audio Wiring
Recommended cable for s-video/composite and audio purposes is PIC 75 Ohm Coax,
P/N V76261. This is a lightweight, flexible, and low signal loss cable which meets FAA
flammability requirements of FAR 23.1359(d), FAR 25.853(a) and FAR 25.869(a)(4).
Similar aviation coaxial cable can be used from other vendors, as well.
Some aircraft are prone to AC noise - we recommend adding to the composite source a
75 Ohm video isolation transformer such as Deerfield Laboratory, Inc. Part No. 162-1
(www.deerfieldlab.com, [phone]). In most cases this should be added to the video
output of the source.

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 6 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
VGA Wiring
Recommended cable for VGA purpose is ECS P/N 453005. This is a single shielded
cable containing 5 separate coaxial cables, color-coded to match the functions of the
wires.
The individual wires should be extended with 6” 22awg wires using an environmental
splice for the red & green wires, and Raychem caps for the blue, white, and black wires.
Mounting and Base Information
The FD102ARM mates with a drink rail mount (FDBASE, below left), a wall mount
(FDBASE-W, below right) or a flush wall mount (FDBASE-W-FM, not shown).
The connector seats deeply in the mount and is held in place by either gravity or a locking
pin. The secure High Density DB15 pin and connector can only be connected one
direction. The mount is keyed to prevent inadvertent misalignment.

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 7 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Power and Ground Wiring
22 AWG wire is recommended for Power and Ground applications.
Power/Video
There is one High Density DB-15 inset in the bottom of the arm.
This male DB-15 has Power, Composite Video #1, Composite Video #2 and VGA
connections.
Part Numbers for DB-15 connectors, manufactured by Tyco or Amp.
High density, D-sub, 15 contact receptacle (female) P/N 748565-1
HD15F pins P/N M39029/57-354
Pin
Number
Description
1
12VDC Power (28VDC for FD102ARM (28V))
2
12VDC Ground (28VDC for FD102ARM (28V))
3
N/C
4
Composite Video #1 - Signal
5
Composite Video #1 - Shield
6
N/C
7
Composite Video #2 - Signal
8
Composite Video #2 - Shield
9
Red Video (RGB/VGA)
10
Green Video (RGB/VGA)
11
Blue Video (RGB/VGA)
12
Red Ground (RGB/VGA)
13
Green Ground (RGB/VGA)
14
Horizontal Sync (RGB/VGA)
15
Vertical Sync (RGB/VGA)

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 8 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Operation Instructions
The FD102ARM is continuously on but can be de-energized by removing power from the
entertainment system. No pilot or aircrew action is necessary during flight or ground
operation.
The passengers will be able to change the video output from the FD102ARM using the
video source select switch on the LCD monitor, or remotely throughout the cabin with the
included IR remote.
Button Controls
BUTTON
FUNCTION
DESCRIPTION
1
POWER
Press to turn the monitor on if currently off. Hold to turn the
monitor off.
2
SOURCE
Press to switch between sources.
3
UP
Press to increase the value of a menu item.
4
DOWN
Press to decrease the value of a menu item.
5
MENU
Press to activate Menu.

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 9 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Remote Control Buttons
The remote control included with the FD102ARM contains the same functionality available
on the display buttons, to include power, source, menu, and directional arrows.

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 10 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Technical Drawing

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 11 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Technical Support
Should you have any questions concerning this product or other FDS Avionics Corp.
products, please contact our Product Support representatives at [phone].
FDS Avionics Corp.
6435 Shiloh Road
Alpharetta, GA 30005
Phone: [phone]
Fax: [phone]
Email: [email protected]
For further product information, technical data and sample wiring diagrams, please click on
the Dealers section of our web site at www.FDSAvionics.com
Instructions for Continued Airworthiness
The FD102ARM is designed not to require regular general maintenance.

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 12 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Warranty Information
All FDS Avionics Corp. (FDS) products are warranted to be free from material or manufacturing defects for a period
of 24 months from the date of shipment for General Aviation customers or 12 months from the date of shipment for
Government/Special Mission customers. Any material or repair workmanship for in warranty repair service will be
specifically warranted for 90 days or the remainder of the original warranty period, whichever is longer. If the
original warranty period has expired, the 90 day repair warranty is limited to the material and workmanship specific
to the repair activity completed.
The following conditions are exclusions to warranty coverage:
1. Labor costs associated with installation, removal or reinstallation of any product.
2. Damage to or malfunction caused by any unauthorized alteration made to the product.
3. Resolving signal quality issues caused by externally generated noise introduced by aircraft electrical
systems or other components connected to any FDS product.
4. Any malfunction caused by improper installation or connection to aircraft wiring, industry standard cabin
management/ inflight entertainment systems, or third party commercial equipment not specifically identified
as compatible with FDS products.
5. Any malfunction caused by installation that does not conform to precautions associated with operating
environments listed in the operating manual or consistent with industry best practices such as; high
temperature, adequate ventilation, high humidity, high dust, or power surges.
6. Cosmetic damage or damage to internal components caused by installation or removal, failure to follow
installation or operating instructions, or any neglect or misuse of the product.
7. Any product that is returned for service with a broken tamper evident seal, indicating tampering or improper
handling of the product by an unauthorized person. Violation of product tamper evident seals or
modification of factory installed serial and PMA labels voids any warranty, either expressed or implied.
The FDS technical support team is available to provide distance troubleshooting support during business hours
(8:00am to 5:00pm EST) Monday through Friday at [phone].
Many repair requests can be resolved through distance support and may not require return of merchandise to the
factory. If a product must be returned to the factory for repair, an RMA number will be issued as directed by the
technical support team and communicated by the repair coordinator.
Upon request by the customer, FDS may send a service technician onsite to repair any non-PMA products. The
travel expenses incurred to include transportation, lodging and meals along with the technician’s hourly rate shall
be payable by the customer in accordance with FDS’ applicable rates and procedures.
FDS Avionics Corp. will, upon receipt of returned merchandise, remanufacture or replace the unit at our discretion
and return the product by Ground Return Shipping. Express return shipment will be the responsibility of the
sender.
This warranty is not transferable.
Any implied warranties expire at the express limited warranty expiration date. FDS shall not be held liable for any
indirect, special, punitive, incidental or consequential damages.
Some states do not allow limitation on the length of an implied warranty. In such states, the exclusions or
limitations of this limited warranty may not apply.

Document Number:
MAN –FD102ARM
Rev:
G
Revision Date:
05/22/2017
Page 13 of 13
©2017 FDS Avionics Corp.
All Rights Reserved.
TECHNICAL SUPPORT
470-239-7421 or FDSAvionics.com
Log of Revisions
Rev
Date
Page
Description
A
01/25/2007
---
---
B
04/11/2007
N/A
6
Fixed page numbering.
Changed required amperage to 2 Amps.
C
02/13/2009
2,11
Updated specifications, warranty info
D
12/08/2009
1,6,7
Revised Photo, Button Controls, Remote Control
E
10/14/2011
5
Added Operating Temp, New Format, new VGA &
Technical Drawing
F
08/24/2012
Updated format, warranty and non-PMA info
G
05/22/2017
All
New Corporate Name, Branding, Format, Warranty