feather&black Cambourne User manual

Cambourne Bed Frame
Double
King
Super King
MK1 2106 07
Two person
assembly
1 hour approx
assembly time

Cambourne Bed Frame - Assembly guide - Page 2
Assembly tips
Before you begin, it’s best to identify all parts and fittings to build your bed.
We advise laying these out on the floor to check you have everything, and
familiarising yourself before building.
We recommend that you build your new bed in the room you’d like it to be
located - this will help prevent any risk of damage to your newly built bed
whilst moving it.
Top tip
Thank you
Safety and care
It’s really important to ensure children and animals are kept away from the
assembly area, as there are small components used in this bed which could
present a choking hazard. All plastic and wrapping materials should also be
To keep your little ones busy, there is a colouring page inside the back cover.
Help and support
At Feather & Black, it’s our mission to give the whole nation a great night’s
sleep - this means that the quality of our products is of utmost importance to
us. If there are any issues with your product or any missing parts, please
contact our Help Centre on 01243 380 600 where a member of our team will
be happy to help.
Recycling
Please ensure that packaging is disposed of in a safe and environmentally
friendly way, and recycle where possible. Our assembly instructions are
printed on recycled paper. Please keep your assembly instructions safe
to refer back to in the future.
Hello, thanks for choosing to purchase your bed from Feather & Black - you're now on your way
to your best ever night's sleep. Before you begin building your bed, please take a moment to read
through the instructions and make sure that you've got all the relevant parts listed on the
following pages.

A
1
1
1
1
B
C
D
G
E
F
F
F
F
E
HI
Parts list
Parts
Important information
.
The bed you have purchased comes with sprung slats, please follow the instructions below in the
current order. The metal frame & slats (G), the support legs (H&I) and support leg bolts (p) are
packed in the sprung slat frame carton that is supplied as a separate pack.
Tools required
0 1 2 3 4 5 6 7 8 9 1010 11 12 13 14 15 16 17 18
cm
Cambourne Bed Frame - Assembly guide - Page 3
1
1
2
4
2
A. Headboard
B. Footboard
C. Side Rail - LH
D. Side Rail - RH
E. Metal Connection Plates
F. Legs
No more tools needed.
G. Sprung Slat Frame
H. Sprung Slat Frame Centre Support Leg
I. Sprung Slat Frame Outere Support Legs
These parts are supplied in the Sprung Frame Carton

A
A
A
B
B
C
C
D
&C
D
&
C
D
&
D
E
Spring washers for
g x4 h x4
Allen key for M6 bolts
j x1 v x4
f x4
Bolts (M6x40mm) for
fitting the sprung slat frame
(G) to side rails (C&D)
Sleeve nuts for M6 bolts
Bed assembly - use hardware pack 'A'
Cambourne Bed Frame - Assembly guide - Page 4
1
a x12 b x14
c
x14
e
x2
ax4 bx4 cx4
ax2 bx2
cx2
ebc
100%
Hardware pack (B) needed for fixing sprung slat frame to side rails - packed in side rail pack, 3 of 3
80%
80%
80%
Make certain the bed is squared up
as shown in the diagram then tighten
all bed assembly bolts 100%.
d
x1
Spring washers
Bolts (M8x25mm) for fitting
side rails (C&D) to headboard
& footboard (A&B)
a x12 b x16
for M8 bolts
c x16
Allen key for M8 bolts
d x1
Bolts (M8x45mm) for
fitting slat support
rails to headboard (A)
e x2
Please check you have all the parts listed below with your product:
Fittings
Hardware pack (A) needed for fixing side rails and legs (F) to headboard & footboard - packed in side rail pack, 3 of 3
p x8
M6 bolts
Flat washers for
M6 bolts
Bolts (M6x15mm) for
fitting legs (H&I) to the
sprung slat frame (G).
for M8 bolts
Flat washers
k x2 l x1
Spanner for M8 nut
Nuts for M8 bolt

Cambourne Bed Frame - Assembly guide - Page 5
3
Fitting sprung slat frame - use hardware pack 'B'
20mm 60mm 100mm
F
F
1. The support legs each have four adjustable parts that need to be set to suit the height of the bed slat frame.
Please adjust the height of each leg by selecting the correct hole and inserting the bolts and nuts as shown.
.roolfehtsehcuottsujtiostuoronitoofelbatsujdaehtgniwercsybgelhcaefothgiehehtenut-enifnacuoY.2
Carefully turn bed on it's side making sure it is lifted evenly without
twisting. Screw in the legs and then with help, lift the bed into mid-air,
turn it 90 degrees, then lower all four legs onto the floor at the same
time. This is to prevent the whole weight of the bed damaging the legs.
b x2
c
x2
2
bc
k
l
k
x2
l
x1

Cambourne Bed Frame - Assembly guide - Page 6
Fitting sprung slat frame cont.
px8
jx1
p
p
p
p
p
p
Open the sprung slat frame (G) and
lay face down on the working
surface. Fit the support legs (H & I)
to the positions shown securing
with the bolts (p).
Fully tighten using allen key (j ).
H
I
G
I
5
h x4
gx4
fx4 j x1
f
g
h
v
Finally, please check carefully
that all bolts are fully tightened
before the bed is used.
G
v x4
4
Carefully turn the frame over and position evenly onto
the metal slat supports on each side rail. Align the
frame with the fixing holes at each end and secure
using four sets of bolts (f), spring washers (v), flat
washers (h) and sleeve-nuts (g).
When all in place tighten using allen key (j ).

Care and maintenance
Here are some tips to keep your new bed in tip-top condition
Cleaning
To clean your new bed, we'd advise using a warm damp cloth or if fabric,
remove dust using a low suction vacuum cleaner - please do not use abrasive
chemicals or bleach as this may damage the product.
Checking and moving
Periodically we recommend you check that the screws or fixtures haven't
become loose over time. To move your new bed, we recommend lifting it where
possible, as dragging or pushing it could cause damage to your flooring.
Wood
Please note each of our wooden pieces are unique, meaning that markings and
shade can vary slightly between beds. Over a period of time, the wood might
lighten or fade slightly due to light exposure.
Fabric
Please note depending on the lighting, positioning and surroundings of your
period of time the colour might lighten or fade slightly due to light exposure.
Metal
Metal tends to be more resilient to everyday wear and tear. We recommend to
gently dust your metal furniture and keep it dry to maintain its look.
Thank you for shopping with us - we hope you have a great night's sleep,
L
30
5
W
H
Overall Dimensions (LWH cm)
Double:
King:
Internal Dimensions (LW cm)
Double:
Super King:
King:
Distance between slats (cm)
Double: 4.7
King: 5.2
Super King: 5.2
Super King:
31.5
18.5
210 x 148.5 x 95.5
220 x 163.5 x 95.5
220 x 193.5 x 95.5
193 x 138
203 x 153
203 x 183
Cambourne Bed Frame - Care and maintenance guide - Page 7
5
Slat width
6
6
24
Floor to top
of slat
Top of side rail
to top of slat