feather&black Provence 3 Door Wardrobe User manual

Step By Step Assembly Instructions
Page 1
PRE-ASSEMBLY PREPARATION
1. Please check the part contents before attempting to assemble this product. A full checklist of
components is given in this leaflet. If any components are missing, please contact the retailer from
whom you bought this product.
2. This product is HEAVY, it should be assembled as near as possible to the point of use. TAKE
CARE WHEN LIFTING to avoid personal injury and (or) damage to the product.
3. This product takes approximately 90 MINUTES to assemble with 2PEOPLE.
4. The fittings pack contains SMALL ITEMS which should be KEPT AWAY FROM YOUNG
CHILDREN.
5. Read this leaflet in full before commencing assembly.
6. You will require a cross head screwdriver to assemble this product.
7. WE RECOMMEND that you lay a protective cloth on your carpet to prevent marking.
Provence Collection
3 Door Wardrobe

Page 2
Panel and Fittings Identification
Item Description Qty.
ABase 1
Item Description Qty. Item Description Qty.
BLeft Side Panel 1CRight Side Panel 1
DCentre Upright Panel 1ETop Cornice 1FNarrow Back Panel 1
GWide Back Panel 1HWide Door Frame 1INarrow Door Frame 1
JShelf KWide Hanging Rail LNarrow Hanging Rail
MHanging Rail Supports
N42
16mm CSK Screws
R
15 Q12
30mm CSK Screws Dowel
O
Drawer Frame
1
1
1

Step 2
Page 3
Use the adjustable levelers
to level the wardrobe base
(A) on uneven floor
surfaces. Place dowels (Q)
both top and bottom of each
panel.
With the aid of an assistant,
locate the side panels
(B&C) and the centre panel
(D) into the base unit (A).
Secure the side panels
using one 30mm CSK
screw per panel inserted
through the rear post.
P x 3
Q x 12
POSTS
TO REAR!
The adjustable
levelers are attached
on the bottom of base
by the vendor.
Step 1With the aid of an assistant,
locate the drawer frame
(M) to the base unit (A) as
shown.

Step 3IMPORTANT NOTE:
PLEASE ENSURE THE
DOORS ARE UNLOCKED
PRIOR TO ASSEMBLY With
the aid of an assistant, locate
the wide door frame (H) onto
the wardrobe and locate the
narrow door frame (I) onto the
wardrobe as shown. First
secure to the side panels
using four 25mm csk screws
(O) per side, inserted through
the wooden blocks. Then
secure at the bottom using
five additional 25mm CSK
screw (O).
SHOWN WITH DOORS
REMOVED FOR CLARITY
OF ILLUSTRATION ONLY
Step 4With the aid of an assistant,
locate the cornice (E) as
shown. Secure using twelve
30mm screws (P), three for
each panel and four into the
top of the door frames.

Step 5Before attaching the back
panels (F & G), move the
wardrobe close to the position
where it will be used. With
uneven floors you may need
to lean the wardrobe slightly
left or slightly right to ensure
that the doors remain square.
With the side of an assistant,
hold the wardrobe in position
and secure the wide back
panel (G) to the rear of the
wardrobe. DO NOT SECURE
TO THE CENTRE PANEL
YET. Finally, secure the
narrow back panel (F) noting
that it overlaps the wide back
panel. Tighten all twenty one
25mm CSK screws (O).
Step 6Push fit the four shelf pins (R)
at the desired heights. Locate
the shelf (J) noting the
'Notched' corners as shown.
Screw the screws (S) into the
underside of the shelf through
the pins. Then push fit the
hanging rail (K & L) to the
hanging rail supports (N).
SHOWN WITH DOORS
REMOVED FOR CLARITY
OF ILLUSTRATION ONLY
O x 21
S x 4
R x 4

Step 7Move the wardrobe into position and then check that the doors are aligned correctly.
If necessary adjust the door hinges as shown below.
Vertical Adjustment Horizontal Adjustment Lateral Adjustment

It may be required to adjust the top and bottom locking pins on the door frame, enabling the
hooks to locate and lock onto the pin. If required loosen and remove screws on the pin and
locate into the correct position, then re-attach the screws. The pins can be moved in the
directions shown in the diagram.
Pin
Hook
Provence Collection
3 Door Wardrobe