Feelworld F970 Instruction sheet

5.5″ High Bright Monitor
F970 Install and Power Kit
User Manual

1
Foreword
Thank you for purchasing our 5.5-inch high bright touch screen monitor.
Please read this manual carefully before using the unit. Have a great
experience!
Caution
● Please avoid the heavy impact and drop onto the ground when move the
product.
● The screen of this product is made of glass. Please do not drop the screen
towards the ground. Keep away from injury if the screen is broken.
● Keep the product away from the heat source, and avoid the prolonged
exposures to the sun as the LCD screen will be damaged.
● To avoid damaging the product, please do not take apart or repair the unit by
yourself without the adjustable components in the unit.
● In order to better maintain the LCD screen and protect the cover, please
follow the following ways to avoid damages.
1. Please refrain from using the hard objects to hit the screen.
2. Please do not force to wipe the screen.
3. Please do not use the chemical solutions to clean the screen.
4. Please do not spray any detergent on the screen.
5. Please do not write on the screen directly.
6. Please do not stick on the screen.
7. Please simply wipe with a clean soft cloth and make sure no water on the
screen.

2
Key Features
5.5-inch 1920x1080 full HD IPS screen
Touch screen and intuitive button operation, meet different
needs.
High Brightness 1600nits, visible in sunlight
Supports 3D LUT Log to REC.709 and user 3D LUT upload (up
to 32).
Sony F970 external install and power kit design can be used to
install and supply power to external equipment, easy to install and
disassemble, simplify your photography equipment.
With Waveform, Vector scope, RGB Histogram, Focus Assist,
Monochrome etc. functions, can help you accurately exposure
and focus every shot.
Multiple power supply modes, DC IN 12V, Type-C 5V and NP-F
battery slot.
Stereo Earphone output
DC 8.4V power out to power your DSLR camera or mirrorless
camera.

3
CONTENTS
1. Product Description ----------------------------------------- 4
1.1 Front Panel Instruction -------------------------------------- 4
1.2 Rear Panel Instruction --------------------------------------- 4
1.3 Top Button Instruction --------------------------------------- 5
1.4 Bottom Port Instruction -------------------------------------- 6
1.5 Left Port Instruction ------------------------------------------ 6
1.6 Power Supply Way ------------------------------------------- 7
1.7 Sony F970 Install and Power Kit ------------------------- 10
1.8 Mount Points -------------------------------------------------- 10
1. 9 Sunshade ----------------------------------------------------- 12
2. Menu Operation Instruction ------------------------------ 13
3. Menu UI Interface Instruction ---------------------------- 14
4. Menu Function Instruction -------------------------------- 15
5. How to Load LUT --------------------------------------------- 21
6. Technical Parameters --------------------------------------- 22
7. Trouble Shooting --------------------------------------------- 23

4
1. Product Description
1.1 Front Panel Instruction
Indicator: After connecting the power, the indicator light is on (red).
Long Press button to turn on the monitor, it turns yellow.
After the signal is connected, it turns green.
1.2 Rear Panel Instruction

5
Battery Lock: The PUSH lock will lock after the battery installed,
please press PUSH firstly before remove the battery.
NP-F Battery Slot: It is applicable to install NP-F series of
batteries.
F970 Install and Power Kit: Installing the external equipment, like
wireless transmitter, LED light, video converter and others which can
be powered by Sony F970 battery. (The details see: 1.7 Sony F970
Install and Power Kit)
1.3 Top Button Instruction
Button
Function when OSD is not
displayed
Function when OSD is
displayed
F1
Custom button F1
/
F2
Custom button F2
/
F3
Custom button F3
/
TOUCH
Turn ON/OFF touch function
/
MENU
Display OSD Main menu
Return to previous OSD menu
∨
Decrease the volume or
backlight
Select next menu item;
Decrease or adjust value of
selected parameter
∧
Increase the volume or
Select previous menu item;

6
backlight
Increase or adjust value of
selected parameter
Power On/Off button; Return/Exit Menu
1.4 Bottom Port Instruction
DC OUT 8.4V: DC power output interface, polarity as the output
power Barrel output for powering your camera with a
separately available DC coupler via adaptor (NP-FW50 Sony &
LP-E6 Canon&DMW-BLF19 Panasonic). More adapters coming
soon.
:3.5mm earphone port output
DC IN 5V (Type-C): Type-C power input. It is recommended to be
used for local power supply only. It is not recommended to connect
other devices to provide loop-out power.
1.5 Left Port Instruction (Left)

7
HDMI IN: V1.4, HDMI signal input, up to 4K@30Hz.
HDMI OUT: V1.4, HDMI signal output, up to 4K@30Hz.
DC IN 12V: DC power input, polarity as the input power
1.6 Power Supply Way
(1) The rear cover of the monitor is equipped with a F970 battery plate,
which is applicable to F970 series of batteries.
● Sony F970 battery plate for battery of Sony DV:
Sony F970 F960 F950 F930 F770 F750 F730 F570 F550 F530
series.
It is recommended to use standard original F970 battery.
When using battery power supply: two power output interfaces (DC OUT
8.4V interface and external install and power kit) can be connected to other
device. When powering other device, it is recommended to choose a
battery with a larger capacity, so the longer the use time.
Remark: Please take off the battery from the monitor if you
don’t use the monitor in a long time.
(2) The left side of the monitor has a DC 12V input power port
(5.5mm outer, 2.1mm inner) and supports 7 ~ 24V wide voltage.

8
The DC power adapter needs to be purchased separately.
When using external adapter input: two power output interfaces (DC OUT
8.4V interface and external install and power kit) can be connected to
other devices. When powering other equipment, it is recommended to
equip at least 3A power adapter.
(3) The bottom of the monitor has a Type-C 5V input power port.
This port can be connected to the power bank for power supply and is not
used for data transmission; it is recommended to be used only for local
power supply, and it is not recommended to connect other devices to
provide loop-out power.
1.7 Sony F970 Install and Power Kit
A Sony F970 external install and power kit design is added to the back
of the monitor. The external kit can be used to install and install the
external equipment, like wireless transmitter, LED light, video
converter and others which can be powered by Sony F970 battery.
The kit has two cross grooves, you can adjust the position of the external
device by loosening 2 screws up and down / left or right, or install the kit
upside down. When you don't need the kit, you can loosen the screws and
remove the kit.
Note: Before disassembling the kit, make sure that the monitor is
turned off, and then remove the battery or power adapter.
(1) Just move the kit: Loosen 2 screws, and then adjust up / down / left / right.
(2) Remove the external device: After the plug-in device is installed on the kit, if
your plug-in device has a locking button, and it is more difficult to press it to
remove it by hand, then you can use our assisting tool to disassemble.

9
(3) Steps to remove the kit:
①. Loosen the 2 screws.
②. Use both hands to move the kit up.
③. Move the round holes to the corresponding 2 screws.
(You can also install the kit upside down.)

10
④. Then gently lift the kit upwards and carefully disassemble the 2P power cord.
⑤. Then remove the 2 screws.
(4) Install back to the kit: first screw the 2 screws back to the screw hole used to
install the kit on the back of the monitor, install the 2P power cable to the cutout,
then align the round hole of the kit with the screw, and then push the kit to the
screw at the center of the kit cross, then tighten the screws.
1.8 Mount Points
(1) ¼-20 Thread Points
There are (4) ¼-20 thread points (top, bottom, right side & Back center) can be
easily connected to the hot shoe mount, tripod fixed installation.

11
(2) Tilt Arm Mounting
The monitor secures to your camera using the included Tilt Arm via shoe mount
or 1/4"-20 thread.
• Allows the monitor to rotate 360 degrees for viewing convenience
• Secure and lightweight mounting via shoe mount or 1/4"-20 thread
• Includes a shoe mount of its own for accessories like a microphone, LED light, or
wireless receiver, etc.
• There are two small dots on the tilt arm, which are aligned with the monitor for
installation, the connection is more stable, just grab the monitor to rotate without
loosening the screws.

12
1.9 Sunshade
①Sunshade ②Sunshade Frame
③Fixed Frame ④Sunshade Application
First lock the Sunshade Frame ②with the monitor tight ③.
Open the sunshade ①, and match the sticker on the sunshade

13
inside to the marked part of the sunshade frame ②, smooth and
press 3 sides on the sunshade, and then complete the sunshade
installation ④.
2. Menu Operation Instruction
After the monitor is correctly connected to the power supply, the
indicator light is on (red), long press , turn on the monitor,
the indicator light turns yellow, and after the HDMI signal is input,
the indicator light turns green.
After turning on the power, you can press the TOUCH key to select
turn on/off the touch function.
(1). Touch screen menu operation (default touch screen is on)
①．Double-click on the screen to open the main menu (on the left side of the
screen) and click on the corresponding menu to display the secondary
menu. You can enter the corresponding function option and click directly
to select or set. Click the touch screen to exit the menu.
②．When the menu is not displayed, swipe up from the bottom of the screen to
open the shortcut menu, and click the function icon to open the
corresponding function, click the icon again to exit the function. Swipe the
shortcut menu left and right to select more functions. Click the touch
screen outside the shortcut menu to exit the shortcut menu display.
③．On the left side of the screen (1/2 split screen), you can directly adjust the
brightness of the screen backlight; on the right side of the screen (1/2 split
screen), you can directly adjust the volume.
Figure:

14
(2) Button Menu Operation
①．When the menu is not displayed, directly press the "∨" or "∧"button to
adjust the volume or backlight. You can set the left and right buttons in the
in the Left Right Key Set
of menu User Option
②．Press “MENU” button to enter OSD main menu, press MENU button again
to enter secondary menu, then press “∨”or “∧”button to select items,
after selected press MENU button to confirm and enter function menu,
press “∨”or “∧”button to select the corresponding function or adjust the
parameters.
③．Press button to return / exit the menu
3. MENU Interface Instruction

15
4. Menu Function Instruction
Assist
All Waves
On, Off
After turning on, waveform, vector, histogram and embedded
audio will be shown.
Waveform
On, Off
Mode：RGB、YUV、Y
This essential feature assists with the calibration of professional
video cameras. It shows the overall brightness of the image
assisting the video professional in correcting exposure. The
waveform feature also checks the evenness of the lighting when
lighting a chromakey or background.
Waves Trans.：Off, 25%, 50%, 75%
On, Off

16
Vector
shows how saturated the image is and where the pixels in the
image land on the color spectrum.
Histogram
On, Off
Mode：RGB1、RGB2、Y
RGB Histogram:It can display the graphic of color tone
distribution, can intuitively display the exposure status of the
image, and display overlapping histograms in red, green, and
blue channels
Y Histogram: A quantitative tool to check the picture brightness,
display different color for different brightness.
Focus Assist
On, Off
Color：（Red, Green, Blue）
Peaking Level：you can adjust the peaking level after
turning on（1～10）
It highlights the areas that are in focus so you are able to quickly
focus the camera and not miss crucial shots.
Embedded Audio
On, Off
The Audio Level Meters provide numerical indicators and
headroom levels.
Over Exposure
On, Off
Exposure Level：you can adjust the exposure level after
turning on（10~100）
Areas of the image over a certain threshold are filled with a
striped pattern to dramatically highlight areas where too much
light is falling on the image sensor.
Check Field
On, Off
Mode：Red, Green, Blue, Mono
When enabled, hue and saturation adjusted quickly and
accurately

17
False Colors
On, Off
Mode: Normal, ARRI
An image that depicts an object in colors that differ from those a
photograph (a true color image) would show.
Marker
Grid
On, Off
Mode: 2x2,3x3,4x4,5x5,6x6,7x7,8x8,9x9
Color: Red, Green, Blue, Black, White, Gray
The area of the picture can be divided into 4, 9, 16, 25, 36, 49, 64,
81 equal grids.
Safe Frames
On, Off
Mode: 80%, 85%, 90%, 93%, 96%, 2.35:1
Color: Red, Green, Blue, Black, White, Gray
Center Marker
On, Off
Color：Red, Green, Blue, Black, White, Gray
Ratio Marker
On, Off
Mode: 4:3、13:9、14:9、15:9、16:9、1.85:1、2.35:1
Color: Red, Green, Blue, Black, White, Gray
Modified Mark：0~5
Image
Under Scan, Over Scan

18
Scan Mode
Aspect Ratio
Auto, 16:9, 16:10, 4:3, 5:4, 1.85:1, 2.35:1, Full Screen
Provides a wide variety of aspect ratio to match different camera
anamorphic lenses.
Anamorphic
On, Off
Mode：1.33X, 1.6X, 2.0X, 2.0X MAG, User
Under the User, can be customized（1.20X～2.00X）
Allows you to use anamorphic lenses or adapters and see the
image unsqueezed, even if your camera does not de-squeeze in
camera.
Image Flip
On, Off
Mode: H Flip, V Flip, H_V Flip
Zoom Mode
On, Off
Mode：2X、4X、9X、16X、User
Under the User, can be customized（100%~200%）
It is HD signal in any part, an amplification for high quality close-up.
Image Freeze
On, Off
P2P
On, Off
Enable the filmmaker to check the image from the 1:1 signal source
without scaling.This feature is essential for capturing optimum
detail.
User Option
On, Off

19
LUT
After the LUT Switch is turned on, you can use the Lut
(SLOG2, SLOG3, LOGC, VLOG).
The Lut item is displayed after the Lut Switch is turned on.
LUT is a table for quickly looking up and output specific color
data. By loading different 3D-LUT tables, it can quickly
recombine color tone to form different color styles
Lut Import：Confirm
After copying the 3D LUT file to the USB flash driver then
connecting USB UPGRADE port via Type-C to USB connector,
then click “Confirm” or press “∨” or “∧” to select Lut Import：
Confirm and press MENU to import the LUT file
Lut Table
Show the 4 built-in Lut and the custom load Lut (up to 32）
HDR
On, Off
Mode: HLG1, HLG2, HLG3
HDR can provide more dynamic range and the details of
image, it is better to reflect the visual effects in the real
environment.
Display Adjustment
Backlight：0~100
Adjust the screen brightness
Brightness：0~100
Adjust the image brightness
Contrast：0~100
Adjustment of the ratio between the brightest and darkest parts
of the image . When adjusting, pay attention to the sense of
hierarchy in the image. If the proportion is too large or too