Fellowes POWERSHRED 99Ms User manual

PLEASE READ THESE INSTRUCTIONS BEFORE USE.
DO NOT DISCARD: KEEP FOR FUTURE REFERENCE.
Powershred®99Ms
The World's Toughest Shredders®
1789 Norwood Avenue, Itasca, Illinois 60143 •1-800-955-0959 •www.fellowes.com
Brands
United States: 1-800-955-0959
Canada: 1-800-665-4339
Mexico: 001-800-514-9057
CUSTOMER SERVICE & SUPPORT
www.fellowes.com
© 2017 Fellowes, Inc. | Part #410498
Factory Service

2
CAPABILITIES
ENGLISH
Model 99Ms
KEY
G. Control Panel and LEDs
1. Overheat (red)
2. Bin open (red)
3. Bin full (red)
4. Remove Paper (red)
5. SafeSense
®
indicator (yellow)
6. Reverse
7. ON/OFF (blue)
8. Forward
A.
B.
C.
F.
D.
E.
G.
Will shred: Paper, credit cards and staples
Will not shred: Adhesive labels, continuous form paper, transparencies, newspaper,
cardboard, paper clips, CD/DVDs, laminates, file folders, X-rays or plastic other than noted
above
Paper shred size:
Micro-Cut .................................................................5/64 in. x 9/16 in. (2 mm x 14 mm)
Maximum:
Sheets per pass ........................................................................................................... 14*
Paper entry width........................................................................................9 in. (230mm)
*8.5 in. x11 in., 20lb., (75g) paper at 120V/60 Hz, 6.5Amps; heavier paper, humidity or other than
rated voltage may reduce capacity. Maximum recommended daily usage rates: 1000 sheets per day,
50 credit cards. 14 sheets per pass to avoid jams.
Fellowes SafeSense®shredders are designed to be operated in home and office environments ranging
between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
BASIC SET UP
CASTER INSTALLATION
17
1
17
2
17
3
17
4
17
5
A. SafeSense
®
Technology
B. Paper entry
C. See safety instructions
D. Pullout bin
E. Casters
F. Disconnect power switch
1. OFF
2. ON
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
15
15
• Operation, maintenance, and service requirements are covered in the instruction
manual. Read the entire instruction manual before operating shredders.
• Keep away from children and pets. Keep hands away from paper entry. Always set
to off or unplug when not in use.
• Keep foreign objects – gloves, jewelry, clothing, hair, etc. – away from shredder
openings. If object enters top opening, switch to Reverse ( ) to back out object.
• Never use aerosol products, petroleum based lubricants or other flammable
products on or near shredder. Do not use canned air on shredder.
• Do not use if damaged or defective. Do not disassemble shredder.
Do not place near or over heat source or water.
• This shredder has a Disconnect Power Switch (F) that must be in the ON ()
position to operate shredder. In case of emergency, move switch to OFF (O)
position. This action will stop shredder immediately.
• Avoid touching exposed cutting blades under shredder head.
• Shredder must be plugged into a properly grounded wall outlet or socket of the
voltage and amperage designated on the label. The grounded outlet or socket
must be installed near the equipment and easily accessible. Energy converters,
transformers, or extension cords should not be used with this product.
• FIRE HAZARD – Do NOT shred greeting cards with sound chips or batteries.
• For indoor use only.
• Unplug shredder before cleaning or servicing.
15
15
BASIC SHREDDING OPERATION
Continuous operation:
Up to 20-minutes maximum
NOTE: Shredder runs briefly after each pass
to clear entry. Continuous operation beyond
20-minutes will trigger 40-minute cool down period.
3
Press ON (I) to
activate (blue)
PAPER OR CARD
Feed paper/card
straight into paper
entry and release
Plug in and put
disconnect power
switch in ON (I) position
When finished
shredding set
to OFF ( )
Press and hold forward ( )
2-3 seconds
PRODUCT MAINTENANCE
CLEANING AUTO-START INFRARED SENSORS
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors
may become blocked by paper dust causing the motor to run even if there is no paper present.
(Note: two paper detection sensors are located in the center of the paper entry).
All micro-cut shredders require oil for peak performance. If not oiled, a
machine may experience diminished sheet capacity, intrusive noise when
shredding and could ultimately stop running. To avoid these problems, we
recommend you oil your shredder each time you empty your waste bin.
OILING SHREDDER
15
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
*Apply oil across entry
TO CLEAN THE SENSORS
15
Turn off and unplug
shredder
Locate Auto-start
infrared sensor
Dip cotton swab in
rubbing alcohol
Using cotton swab, wipe
away any contamination
from the paper sensors
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain
illuminated and the shredder will not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and
recovery time for this shredder.
Bin Full: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36053.
Bin Open: The shredder will not run if the bin is open. When illuminated, close the bin to resume shredding.
Remove Paper: When illuminated, press reverse ( ) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry.
SafeSense
®
Indicator: If hands are too close to the paper entry, the SafeSense
®
indicator will illuminate and the shredder will stop shredding. If SafeSense
®
is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding.
TROUBLESHOOTING
LIMITED PRODUCT WARRANTY
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of defects
in material and workmanship and provides service and support for 1 year from the date of purchase
by the original consumer. Fellowes warrants the cutting blades of the machine to be free from
defects in material and workmanship for 1 year from the date of purchase by the original consumer.
If any part is found to be defective during the warranty period, your sole and exclusive remedy will
be repair or replacement, at Fellowes’ option and expense, of the defective part. This warranty does
not apply in cases of abuse, mishandling, failure to comply with product usage standards, shredder
operation using an improper power supply (other than listed on the label), or unauthorized repair.
Fellowes reserves the right to charge the consumers for any additional costs incurred by Fellowes to
provide parts or services outside of the country where the shredder is initially sold by an authorized
reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD
SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages
attributable to this product. This warranty gives you specific legal rights. The duration, terms, and
conditions of this warranty are valid worldwide, except where different limitations, restrictions, or
conditions may be required by local law. For more details or to obtain service under this warranty,
please contact us or your dealer.
14
3
2
2
14
2
14
11
14
4
14
23
SafeSense
®
is active and
working properly
SAFESENSE®TECHNOLOGY OPERATION
Stops shredding immediately when hands touch the paper opening.
Touch test area and
look for the SafeSense
®
indicator to illuminate
Turn the shredder
ON ( ) to activate
SafeSense
®
SET-UP AND TESTING
1
ADVANCED PRODUCT FEATURES
SilentShred™Technology
SilentShred™ noise quality
shreds without noisy disruptions.
14
14
14
2 43
Sleep Mode
Energy saving feature shuts down
automatically after 2 minutes of no
shredding activity.
SLEEP MODE OPERATION
Energy saving feature shuts down the shredder after
2 minutes of inactivity
WHEN IN SLEEP MODE
In sleep mode To get out of sleep mode
touch control panel
insert paper
or
14
3
2
2
14
1
If hand is held on SafeSense
®
area more than 3 seconds,
shredder will shut off
SafeSense®Technology
Stops shredding immediately when
hands touch the paper entry.