Femooi HiMESO User manual

Instruction Manual

Thank you for purchasing the HiMESO™ Nano Meso Device
Before using HiMESO™, please read this manual carefully to ensure correct
and safe use following the instructions.
About HiMESO™ Nano Meso Device
HiMESO™is about to bring you a skincare experience like never before.The nanocrystallite technol-
ogy will open the microchannels in the outer layer of the skin and promotes the deep absorption of
active ingredients and the production of collagen cells. It helps you to regenerate a moist, plump,
white, flawless, firm and, elastic young skin.Below we will show you the unique femooiHiMESO™
and give you a complete understanding of the device.
It can quickly open the barrier to skin absorption channels, allowing nutrients to penetrate
the underlying skin and work deep down.
The unique wireless contact charging design makes daily charging easier.
The 7x7mm Nanocrystalline Needle Surface is higher than the industry standard, the con-
tact area is larger, make it easy to take care of every inch of skin.
Three-button switch mode and simple operation enable you to get started quickly. The
body is small and portable so that you can easily enjoy the beauty while hanging out.
High purity red and infrared light can effectively promote skin repair, nutrient absorption,
and collagen production. It can also fade wrinkles, whiten skin, restore the state of a firm,
elastic skin.
Monocrystalline silicon is biocompatible, safe, and reliable. The purity of the monocrystal-
line silicon used in this product is as high as 99.999% and is lead-free and mercury-free,
ensuring the safety of use.
Through precise design, the essence will not leak out of the body. It will be evenly distribut-
ed and more effectively penetrate the skin.
The diameter of the needles are only one-thousandth of a human hair. The needles are
manufactured by a micro-nano processing technology, with a tolerance level below 80 nm.
Thanks to this process, the needles do not touch the dermis layer and opens the skin
absorption channel while ensuring the integrity of the skin.

Device
Front view Side view
Top cover
Bottom Interface
Cover
Cartridge with serum installation slot
Infrared sensing area
Button
NanoMeso Mode
Phototherapy Mode
Wireless charging port
Phototherapy lamp
(red light + infrared light）
正 面底 部
①
②
③
④
⑤
⑥
⑦
⑧
⑤ ⑥ ⑦ ⑧
① ②③
④

Wireless charging dock
Wireless charging port
Placement slot
Charging cable connector
of the dock
①
②
③
① ②
②
③
W
i
r
e
l
e
s
s
C
h
a
r
g
i
n
g
S
t
a
t
i
o
n
F
H
-
W
C
S
1
.
0
I
P
X
4
I
n
p
u
t
:
5
V
=
1
0
0
0
m
A
O
n
l
y
u
s
e
w
i
t
h
f
e
m
o
o
i
®
H
i
M
E
S
O
™
N
a
n
o
M
e
s
o
D
e
v
i
c
e

Wireless charging dock mirror
Mirror
Wireless charging dock
connector
①
②
①
②
②

Cartridge with serum
Other accessories
Capsule cap
Nanocrystalline needle
surface
Serum chamber
Charging cable
Quick Start Guide

Installation of cartridge with serum
Charging Dock Installation
2.Pull out the cartridge
with serum
1.Remove the cover 3. 4.
Insert the Cartridge
with serum vertical-
ly down into the
installation slot until
you hear a slight
"click" to ensure it is
placed correctly
Place the cover back
on, and it's done
1. Align the backside of the wireless
charging dock with the front side
of the mirror
2. Insert the wireless charging dock
into the slot of the mirror and place
it on a flat surface to use

Usage
Before use, please read the following important information:
·
·
·
·
·
·
·
·
·
·
·
·
Before use, please charge your HiMESO™ until it is fully charged. Please refer to the "Charging"
introductions below for information on how to charge.
Before using it the first time, it is recommended to do a skin test with the essence on the inner
side of the wrist. Stop using it if there is an allergic reaction, such as severe itching and redness.
During the use of Nano Meso Mode, the time of touching each part of the skin should not exceed 3
seconds and should be less than 3 times.
If the disposable packaging of the Cartridge with serum is damaged or leaks, please do not use it
to avoid skin contamination.
During the use of the NanoMeso Mode, the cover plays a protective role to prevent excessive
pressing.When the device is pressed too hard against the skin the device will automatically stop
operation. The normal operation can be resumed by reducing the intensity.
After using the essence, some people may feel slight itching and tingling of the skin, which is
normal and generally does not need treatment. It can disappear on its own within 24 hours.
When finished with using the Nano Meso Mode, please remove the Cartridge with serum and
clean the cover and the installation slot of the Cartridge with serum.
After using the Nano Meso Mode and Phototherapy Mode, some people may develop skin
redness. This is a normal phenomenon and generally does not need to be treated. It can disap-
pear by itself within 24 hours or can be accelerated by using an ice compress as needed.
After opening the cap of the Cartridge with serum for the first time, there may be some leakage of
the essence on the Nanocrystalline needle surface. This is a normal phenomenon caused by the
filling process and does not mean the Cartridge with serum is damaged.
One Cartridge with serum should only be used by one person, it is strongly advised not to share
the capsule with others. Further, it is strongly advised not to use the same Cartridge with serum
after it is empty, since this may lead to allergic reactions of the skin, redness, spots, inflammation
and other adverse effects.
We recommend using the Nano Meso Mode and Phototherapy Mode once or twice per week. You
can also adjust the frequency of use according to your skin condition.Do not use the device more
than once a day. It is best to use it before bedtime so that the skin can better absorb the skincare
products at rest.
Before operation, please clean your hands and the parts to be operated.

Description of the modes
Press and hold the Power button for 1.5 seconds to turn on and off the HiMESO™ device.When
HiMESO™ is turned on, the device will emit a long beep, and the corresponding indicator light will
turn on; when it is off, the device will emit a long beep and the corresponding indicator light will
turn off.
Press the Nano Meso Mode button to turn on the HiMESO™ Nano Meso Mode. The device will
emit a short beep, and the corresponding indicator light will turn on. The Nano Meso Mode
has three intensity settings: low, medium, and high. Press the button again to cycle between the
intensities, each time you adjust to a new intensity, the corresponding indicator will light up
Press the Phototherapy Mode button to turn on the HiMESO™ Phototherapy Mode. The machine
will emit a short beep and the corresponding indicator light will turn on. The Phototherapy Mode
has two settings to choose from: the low-energy red light and the high-energy red light combined
with infrared light. Press the button again to cycle between the two settings. shortly.Each time you
adjust the setting, the corresponding indicator will light up to remind you.
The red light of the HiMESO™ Phototherapy Mode can improve cell activity, promote collagen
production, reduce skin dullness and stains, relieve skin fatigue, improve skin radiance, and delay
aging; The healing power of infrared light can accelerate wound healing, promote blood circula-
tion, allow the skin to better absorb nutrients, improve wrinkles and moisturizing capacity, and
make the pores look smaller.The Nano Meso Mode and Phototherapy Mode can be used at the
same time, improving efficiency and strengthening absorption.

*
Detailed Steps
Red light lamps
Infrared light lamps
Cleanse the face.
During treatment, start at the bottom of the face and move
upwards.
Note:
STEP1:
STEP2:
Tip：
①
②
① ②
The device only starts functioning when the built-in intelligent infrared sensor system senses the
skin
* In order to avoid overuse, the default treatment time of the Nano Meso Mode is 10 minutes each
time, after which the device will continuously beep twice to remind you the treatment has finished.
* In order to avoid overuse, the default treatment time of the Phototherapy Mode
is 20 minutes each time, after which the device will continuously beep twice to remind you the
treatment has finished.
Follow the "Installation of cartridge with serum” instructions to
install the cartridge with serum.Press the Nano Meso Mode
button to turn on the Nano Meso Mode ; If you need to adjust
the intensity, you can press the Nano Meso Mode button
again to select the desired intensity. For specific usage, please
refer to the instructions in the "Description of the modes".Posi-
tion the Nanocrystalline needle surface in horizontal contact
with the skin, you will observe a slight downward motion of the
needle surface. To start the treatment, gently but quickly move
the device up and down.The used force should be adjusted
according to the contact with the skin.
* The infrared light wavelength is beyond the visible range of the naked eye, therefore this light is not
visible during the Phototherapy Mode
Nano Meso Mode

After the treatment, pat the face gently to allow the skin to
naturally absorb the remainder of the essence, it can also be
rinsed away with water.
Cleanse the face.
STEP1:
STEP3:
*
Note:
Please observe your personal skin condition during the treatment to avoid overuse.
* Always first install the cartridge with serum, place the cover, and then turn on Nano Meso Mode
* Before turning on the NanoMeso Mode, please make sure that the cartridge with serum is
installed correctly.When installed correctly, you will hear a slight "click".
* The used force of the device on the skin during the treatment should be moderate. Do not inten-
tionally press it, neither lift the wrist so that the needle surface cannot evenly touch the skin.
* Please be very careful when using the essence in the area around the eyes. Do not let the essence
be in direct contact with the eyelid or eyes.
* It is recommended that users with sensitive skin use the low-intensity setting, and wait for the
skin to fully adapt before trying other settings according to the skin condition.
* Do not drag the device on your face during the treatment.
* Please press the device with a constant force on the skin during the treatment, to make sure the
device can produce a continuous and uniform vibration. When excessive force is used, the device
will enable its protection mechanism and stops working.The machine is more sensitive in the
low-intensity setting, please pay attention to the control of the applied force.
Skin Rejuvenation Mode

* If you experience any discomfort while using femooi HiMESO™, please stop using it
immediately and consult a physician.
+
STEP2:
STEP2:
Place the cover on the device. Press the Phototherapy Mode
button to turn on the Phototherapy Mode and the phototherapy
lamps will turn on. Press the Phototherapy Mode button again to
cycle between the two light intensity settings.For detailed usage,
please refer to the "Description of the modes" instructions.During the
treatment, press the cover firmly against the face, and move the
device slowly from one part of the face to another.Make sure to not
illuminate a single part of the face for more than 3 minutes.
After the treatment, the desired skincare products can be applied as
usual.
*
Note:
Warning:
If the skin feels dry during the treatment, the skin can be hydrated accordingly.
* If you feel that the brightness is too strong when close to the eyes, please close your eyes or wear
a blindfold.
* It is normal for the device to become slightly warm when using the Phototherapy Mode. If the case
is overheated, stop using it immediately.
The Nano Meso Mode and Phototherapy Mode can be used at the same time to promote the
absorption of nutrients while inserting the essence in the skin. Combined usage can also acceler-
ate skin recovery, improve skin care efficiency, and improve skincare quality.
* Do not illuminate the same area of the skin for more than 3 minutes.
Nano Meso Mode + Phototherapy Mode

Your HiMESO™ device can be charged through the charging dock.
Charging
*
*
*
·
When the battery power is too low, the indicator light will continuously flash and at the
same time beep 3 times for 5 seconds, as a reminder.
·
It takes about 4 hours from when the battery is completely depleted to being fully charged.Please
install the charging base according to the "Charging Dock Installation" instructions.After the instal-
lation is completed, insert the DC connector of the charging cable into the charging cable connector
of the dock, and insert the plug into the power outlet.Align the charging port on the bottom of the
Himeso™ device with the charging port on the wireless charging dock, and insert it into the place-
ment slot with the back facing the mirror. When the device's indicator lights pulses in a breathing
rhythm, it means the battery is charging.
When charging is completed, the indicator light changes from the breathing pulse into being steady
on.
Before charging, make sure that the charging cable connector is dry and free of water, and
check whether the marked voltage matches the voltage of the power outlet.
Do not charge in places where there is a possibility of immersion in water.
The mirror is fragile. Please handle it gently when using it.
Warning:

Please maintain HiMESO™ properly and keep it in the best working condition
· After each use, please clean the cover and the slots inside of the device thoroughly with
a clean cloth or towel, and wipe them dry.
· Please wipe the charging base with a soft cloth or towel.
· After finishing the Nano Meso Mode and Phototherapy Mode, please remove the cartridge
with serum and clean the Cartridge with serum installation slot.
· Please do not use cleaning products containing alcohol, gasoline, or acetone to clean the
device. These substances may irritate the skin.
· Please do not place HiMESO™ in an acidic or alkaline liquid.
· Please do not put HiMESO™ in a dishwasher, microwave oven or high-pressure container,
otherwise it may cause an accident or cause injury.
· Please do not wash the HiMESO™ device with water.
· The device must not be immersed in water.
· Please avoid exposure to high temperatures, moisture, heavy pressure and impact.
· Please keep the product out of reach of children to prevent accidents.
· Please do not use it near electrical appliances such as TVs and radios.
· Please do not use while the product is charging.
· Please charge HiMESO™ when it is in a low battery state to extend the battery life.
· Please use the original charging dock and charging cable of HiMESO™.
· Please do not disassemble, modify or repair the device by yourself.
· Please use the product only for the specific purposes described in this manual.
Maintenance
Frequently Asked Questions
The most frequently asked questions about HiMESO™ are listed below.If you cannot find
proper answers, please call the customer service hotline for more information.
The indicator light of HiMESO™ does pulse in the breathing rhythm after the charger is
connected
The battery is completely depleted and it can take a few minutes to recognize the charger.
The HiMESO™ device is not properly placed in the charging base.
HiMESO™ does not respond after pressing the function mode button
Cannot switch to other modes
· The device is turned off.Please press and hold the power button for 1.5 seconds to turn on
the device.
The battery is depleted.Please charge the device.
The microprocessor has a temporary malfunction.Please connect the charging cable to
restore its function.
Please ensure that the buttons and fingers are clean and try again.
·
·
The HiMESO™ charging cable connector or power charger are not connected properly.·
·
·
·
If the device cannot switch during use, there may be residual essence in the device. Please
put it in a ventilated place to dry for one to two days before trying again.
·

This device should not be disposed of as household waste. Instead, it should be collected at
an appropriate recycling point for electrical and electronic equipment. By ensuring a correct
disposal of this device, you will help to contribute to the environment and human health.
Further, by recycling this product, you will help with conserving natural resources.
Disposal
Product Name: femooi ‒HiMESO™ Nano Meso Device
Product Model: FH1.0
Product Material: ABS plastic
Product Color: Sakura Pink, Champagne Gold
Product Size: 160×53×36 mm
Product Weight: 115gr
Base Size: 140×130×99 mm
Base Weight: 156gr
Rated Input: 110v-240v
Battery: lithium-ion battery 1200 mAh 3.7 V
Charging Time: 4 hours
Battery Standby Time: 280 days
Interface: three buttons, six indicator lights
Product Specifications
HiMESO™ does not vibrate after pressing the Nano Meso Mode button
The battery is depleted. Please charge in time.
The infrared distance sensor does not detect the skin, please hold it closer to your face.
·
·
If the force is too hard, the device will enable its protection mechanism. Please reinstall the
cover and the cartridge with serum to disable the protection mechanism.
·
After pressing the function mode button, the device immediately turns on without
approaching the skin
The infrared sensor senses the presence of another object. Make sure there are no other
objects within the sensing distance of the infrared sensor.
The outside of the infrared sensor is dirty, please clean it and try again.
·
·
The microprocessor has a temporary malfunction, please restart.·

Disclaimer: Product users are at their own risk.femooi and its distributors assume no
responsibility or liability whatsoever for any bodily or non-physical injury or damage that
occurs as a direct or indirect result of the use of the product.In addition, Femooi reserves the
right to modify this manual and make changes to it at any time and is not obliged to notify
any individual of these changes or changes. In case of dispute, the company reserves the
right of final decision on the interpretation.Within the scope of the law, the company reserves
the right of final interpretation.
Note: Product or part specifications are subject to change without notice.
©2020 Femooi Technologies, All rights reserved
Femooi (Netherlands): Femooi BV
Address: Kennedyplein 200，5611 ZT Eindhoven, Netherlands
Femooi (China): Ningbo Femooi Intelligent Technology Co., Ltd
Address: 8F, fengting Building, No. 375, Jiangdong North Road, Ningbo, China
Mainland China customer service hotline: [phone]
www.lovefemooi.com