Ferei HL20AA II User manual

FEATURES
1 High Intensity LED headlamp.
2 Extra spot beam.
3 Cool or neutral white LED version available.
4 IPX4 Water resistant.
5 1000 lumens for 16 hours.
6 8 Selectable brightness levels from 10% to 80%.
7 4 selectable blinking modes: police blinking, slow blinking, quick
blinking, and SOS.
8 Smart IC motherboard provides multiple brightness settings ,and
prevents overheat, over discharge or damages caused by polar
reversing.
9 The light will emit 10 successive blinks in 8 seconds when Battery
level indicating around 20% capacity.
10 Elastic bungee headband capable of length adjustment, providing
best fit and comfort for user.
11 Optional Diffuser and USB cable charger available.
12 Optional BP2836B, BP4836B and BP6836B for longest runtime each
9 hours, 18 hours and 27 hours on High.
USAGE INSTRUCTIONS
1 Briefly press the rubber switch to turn the HL20AAII on/off.
2 The HL20AAII provides three lighting options:
•Maximum brightness: 100% output
•Custom brightness: eight selectable modes ranging from 10% to
80% output
•Strobe / SOS: police strobe, slow strobe, rapid strobe and SOS.
3 Operating Instruction:
•i) To turn the HL20AAII on, briefly press the rubber switch. The default
setting is maximum brightness (100% output).
•ii) To access custom brightness mode: with the HL20AAII turned on
(in either max or custom mode), hold the switch down for more than
2 seconds and the HL20AAII will cycle through 8 levels of output.
When a desired output is displayed simply release the button to set
the brightness.
•iii) The HL20AAII has 3 hidden strobe modes and 1 SOS mode. To
access these modes simply hold down the power button for 2
seconds with the unit turned off and release. To cycle to the next
strobe / SOS mode once again hold for 2 seconds and release. To
exit strobe / SOS mode simply press the switch once (turns the
HL20AAII off).
4 Low battery warning: When the battery capacity gets very low
(approx. 20%), the HL20AAII will emit 10 successive blinks in 8 seconds.
This is a reminder that the battery should be replaced.
5 Reverse polarity protection: When a battery is inserted incorrectly,
a special protection circuit will activate and automatically prevent
operation to ensure the safety of the HL20AAII and its user.
6 The HL20AAII is also designed with intelligent over-discharge
detection. If battery voltage reaches a critical lower limit, the HL20AAII
will automatically turn off, at which time the battery should be
replaced as soon as possible.
WARNING
•Do not use batteries that are banned on this manual.
•Do not mix batteries of different brands, size, capacity or type.
•Be sure to operate the battery box as per the correct instructions so
to avoid any damage.
DIAGRAM
INSTALL AND REMOVE THE BATTERY BOX
AA BATTERY BOX INSTRUCTIONS
USER MANUAL
High intensity
LED Headlamp
HL20AAII
UNSCREW THE NUT BOTH NUTS ARE UNSCREW REMOVE THE SCREW CASE FROM
BATTERY BOX
INSET 3PCS 1.5V AA BATTERY
WITH THE CORRECT POLAR IN AA
BATTERY BOX
PUT THE SCREW CASE IN THE RIGHT
DIRECTION
SCREW UP BOTH NUTS ON AA BOX
ADJUSTMENT BUCKLE
NYLON ELASTIC BAND
HEAD
LED
ADJUSTMENT
DIRECTION
SWITCH
5.5 DC PLUG CABLE
BATTERY BOX 3*AA
* PHOTOS ARE FOR REFERENCE ONLY, PRODUCTS IN KIND PREVAIL!
TWO RUBBER BELTS TO TIGHTEN
ON AA BOX
CONNECT THE 5.5DC PLUG OF HEADLAMP AND THE 5.5 DC JACK
OF AA BOX, AND THEN SCREW UP THE HOLDER
THE DIRECTION OF DC JACK FOR
AA BATTERY BOX SHOULD BE TO
SWITCH BOX OF HEADLAMP
PUT THE AA BOX THRU THE RUBBER
BELT

USER MANUAL
High intensity
LED Headlamp
HL20AAII
Patented product, counterfeiting not allowed.
Shenzhen FEREI Lighting Co., Ltd.
3rd Industrial Zone, Xiakeng Village, Tongle, Longgang District, Shenzhen 518116, China.
TEL: [phone]
FAX: [phone].
E-mail: [e-mail] •Website: www.ferei.com
HL20AA II  PRODUCT SPECIFICATIONS
LED CREE XML2 COOL WHITE
ANSI/FSC MAX CUSTOMIZED SETTING POLICE
STROBE
SLOW
STROBE
FAST
STROBE SOS
LIGHT PER 100% 10% 20% 30% 40% 50% 60% 70% 80% USERDEFINED
OUTPUT LM 1000 100 200 300 400 500 600 700 800 USERDEFINED
RUNTIME H 16 160 80 57 40 32 27 23 20 OVER 16 H
RANGE M OVER 305 METERS
MAXIMUM
INTENSITY 23256 CD
LED CREE XML2 NEUTRAL WHITE
ANSI/FSC MAX CUSTOMIZED SETTING POLICE
STROBE
SLOW
STROBE
FAST
STROBE SOS
LIGHT PER 100% 10% 20% 30% 40% 50% 60% 70% 80% USERDEFINED
OUTPUT LM 940 94 188 282 376 470 564 658 752 USERDEFINED
RUNTIME H 16 160 80 53 40 32 27 23 20 OVER 16 H
RANGE M OVER 208 METERS
MAXIMUM
INTENSITY 10816 CD
WATERPROOF
RATING IPX4
ANTIDROP 1M
DIMENSION 30 MM HEAD DIAMETER
BATTERY 3 X AA BATTERIES
WEIGHT 169 G EXCLUDING BATTERY
NOTE:
THE ABOVE PARAMETERS WERE TESTED BY USING THE AA LR6
HIGH POWER CAPACITY BATTERY
BATTERY SPECIFICATIONS
TYPE DIMENSIONS NOMINAL
VOLTAGE
USABILITY
ALKALINE
BATTERY
AA 1.5V RECOMMENDED √
NIMH BATTERY AA 1.2V USABLE √
NONRECHAR
GEABLE BATTERY
LITHIUM
AA 1.5V USABLE √
RECHARGEABLE
BATTERY LIION
14500 3.7V BANNED X
WARNING
•Do not use batteries that are banned on this manual.
•DO not mix batteries of different brands, size, capacity or type.
•Be sure to operate the battery box as per the correct instructions so
to avoid any damage.
INTELLIGENT TEMPERATURE CONTROL INSTRUCTIONS
This product is designed with a temperature control circuit.
The LED is a heating device that is sensitive to temperatures,
especially high levels of power and brightness. High temperatures
will easily damage or shorten the life of the LED. Ferei designs its
products with an intelligent temperature-control circuit. It measures
the temperature within the LED filament. As the structure of the
lamp differs, the thermal conductivity of the entire lamp is not the
same. In general, the constant surface temperature of the lamp is
50˚C to 60˚C. When it exceeds its programmed temperature, it will
automatically reduce its power to cool down , and the brightness
decreases by small steps. After cooling-down (provided that battery
voltage is sufficient) the power with brightness increases again.
The process of improving its brightness is relatively discrete and will
not produce a flashing effect.
This stepping goes cyclically to maintain the user's safety and the
light's functionality. In conditions of good air-cooling the lamp
delivers light without stepping down even in high levels brightness
mode. There are no preset timers for stepping, but real-time active
temperature measurements, So the actual runtime of the lamp base
on active temperature control to faster or slower battery discharge,
may be slightly longer or shorter runtime than the lamp of data
provided .
MAINTENANCE
1 Wipe the glass lens with a soft cloth at regular intervals to
ensure maximum light transmittance (avoid using corrosive
detergents).
2 Ensure the cable plug and inside of the battery box remain free
of dirt and debris.
3 Unplug the cable from the battery box when unused for
extended periods.
WARNING
•The LED assembly / lamp can become hot when used on high for
extended periods. This is a normal.
•Do not dismantle any of the headlamp’s components as warranty will be
voided.
•Avoid exposing the headlamp to corrosive substances / liquids.
•Avoid storing batteries in the headlamp’s battery box for extended periods.
•Do not point the headlight directly into a person or animal’s eyes as injury
may occur.
•Ferei reserves the right of interpretation of this manual.