Ferei HL40 II R User manual

FEATURES
1 Focusing LED headlamp
2 Zoom-able head for spot and flood beam
3 Cool or neutral white LED version available
4 IPX4 Water resistant
5 1000 lumens for 4.3hours
6 8 Selectable brightness levels from 10% to 80%
7 4 selectable blinking modes: police blinking, slow blinking, quick
blinking, and SOS.
8 Smart IC motherboard provides multiple brightness settings ,
and prevents overheat, over discharge or damages caused by polar
reversing.
9 Battery level indicating at 20% capacity.
10 Elastic bungee headband capable of length adjustment, providing
best fit and comfort for user.
11 Optional Diffuser and USB cable charger available
12 Optional BP2836B, BP4836B and BP6836B for longest runtime each
8.6 hours, 17.2 hours and 25.8 hours on High.
GENERAL USAGE
1 Briefly press the rubber switch to turn the HL40II on/off.
2 The HL40II provides three lighting options:
•Minimum brightness: 10% output.
•Maximum brightness: 100% output.
•Custom brightness: eight selectable modes ranging from 10% to
80% output.
•Strobe / SOS: police strobe, slow strobe, rapid strobe and SOS.
3 Operating Instruction
•To turn the HL40II on, briefly press the rubber switch. The default
setting is minimum brightness (10% output).
•To access custom brightness mode: with the HL40II turned on (in
either max or custom mode), hold the switch down for more than 2
seconds and the HL40II will cycle through 8 levels of output. When
a desired output is displayed simply release the button to set the
brightness.
•The HL40II has 3 hidden strobe modes and 1 SOS mode. To access
these modes simply hold down the power button for 2 seconds
with the unit turned off and release. To cycle to the next strobe /
SOS mode once again hold for 2 seconds and release. To exit strobe
/ SOS mode simply press the switch once (turns the HL40II off).
The brightness level of strobe / SOS mode is determined by the
brightness set in custom mode.
STRETCH THE ROTATION HEAD PART TO ADJUST THE BEAM SIZE AND
FOCUS SPOT
INSTALL AND CONNECT THE BATTERY HOLDER
Installation:
Put the 18650 battery holder in to the silicon sleeve. as shown in the image above.
Connect the DC plug with DC jack of battery holder, and then clockwise to tighten
the fixed DC connector as shown in the image above.
INTELLIGENT TEMPERATURE CONTROL INSTRUCTIONS
USER MANUAL
Focusing
LED Headlamp
HL40 II
ZOOM IN ZOOM OUT
* PHOTOS ARE FOR REFERENCE ONLY, PRODUCTS IN KIND PREVAIL!
4
5
Low battery warning: When the battery capacity gets very low
(approx. 20%), the HL40II will emit 10 successive blinks in 8 seconds.
This is a reminder that the battery should be recharged or replaced.
6
Reverse polarity protection: When a battery is inserted incorrectly,
a special protection circuit will activate and automatically prevent
operation to ensure the safety of the HL40II and its user.
The HL40II is also designed with intelligent over-discharge
detection. If battery voltage reaches a critical lower limit, the HL40II will
automatically turn off, at which time the battery should be recharged
as soon as possible. Over-discharge of 18650 cells can cause irreversible
damage to the battery and in extreme cases, cause the battery to
inflate and / or emit a harmful gas. It is for this reason that the HL40II
is designed to operate only with 18650 batteries that are above the
lowest acceptable voltage limit.
The headlamp is designed with the Intelligent temperature control
system. As we know, LED is a component which can make heat and
is sensitive to the temperature, it will be damaged or its working life
will be shorten by the overheat temperature, especially the powerful
and brightness LED. So the Intelligent temperature control system
works when the headlamp’s designation and structure cannot realize
the heat-radiation temperature from the high brightness LED lighting.
The system controls the temperature of the LED lamp wick, obviously,
the headlamp gets different Thermal Conductivity with different
structure, and generally speaking, the surface temperature of the
headlamp constant between 50°C to 60°C, when the headlamp runs
heat, the Intelligent temperature control function will help to reduce
the power to cool down the lamp wick, the brightness of the light will
corresponding fell and get lower. And in comparison outdoor using
with the indoor using, outdoor area using will get wind to cool it down
and heat-radiation is better, the LED will crank up the power and the
lights become brighter, and the process of ascension brightness will
smooth and slow without flashes.
At the same time, the intelligent temperature control system will lead
the run time get longer (may be the standard of twice to five times).
Particularly, the run time will depend on the temperature, running
speed even the wind strength, so the actually run time will be a little
different according to the environment of the headlamp using.

Patented product, counterfeiting not allowed.
Shenzhen FEREI Lighting Co., Ltd.
3rd Industrial Zone, Xiakeng Village, Tongle, LonggangDistrict, Shenzhen 518116, China. TEL: [phone] •FAX: [phone].
E-mail: [e-mail] • Website: www.ferei.com
WARM TIPS
In order to avoid accidents, please pay attention to the following tips:
•Never use damaged, discolored or leaking batteries.
•Never use batteries with a damaged sleeve or foil covering.
•Always use 18650 batteries withsafety certificates.
•If the light gets unusually hot when in use, turn it offand check
battery appearance.
•Never store the battery into the battery holder.
•Rechargingis finished when the LED indicator turns to green.
•The battery remains at a normal temperature during recharging. If it
DIAGRAM gets unusual hot, stop recharging andtake the battery out.
•Do notdissemble the charger kit by yourself if the battery couldn’t be
recharged.
•The battery can be used at any time once being recharged. If it
is left unused for longperiods, itshould be recharged for 4 hours
every three months. After being charged they should be slightly
discharged for 10-20 minutes before storage.
•Be sure to always recharge the battery in a safe place and do not
leave unattended while charging.
MAINTENANCE
•Wipe the glass lens with a soft cloth at regular intervals to ensure
maximum light transmittance (avoid using corrosive detergents).
•Ensure the cable plug andinside ofthe battery box remain free of
dirt anddebris.
•Unplug the cable from the battery box when unused for extended
periods.
WARNING
•It is a lighting tool, not a toy. Keepit away from children.
•Shouldnot be aimed directly at the eyes of humans or animals
•Do notplace the light face / lens down when turned on.
•The surface of the flashlight may become hot during extended use.
•Do notdismantle or dissemble any structural parts of the light,
especially the seal parts.
•Dry the light surface with soft cloth immediatelyafter exposure to
water or any corrosive substance.
•Always remove batteries during long periods of inactivity (more than
30 days).
•Ferei reserves the right of interpretationofthis manual.
USER MANUAL
Focusing
LED Headlamp
HL40 II
HL40II  PRODUCT SPECIFICATIONS
LED CREE XML2 COOL WHITE
ANSI/FSC MAX CUSTOMIZED SETTINGPOLICE
STROBE
SLOW
STROBE
FAST
STROBE SOS
LIGHT PER 100%10%20%30%40%50%60%70%80%USERDEFINED
OUTPUT LM1000100200300400500600700800USERDEFINED
RUNTIME INDOOR STATIC TESTING AT 28ºC MAX OUTPUT4.3 43 21.514.310.758.67.26.15.4>4.3
RANGE M OVER 200 METERS
MAXIMUM INTENSITY 10000 CD
LED CREE XML2 NEUTRAL WHITE
ANSI/FSC MAX CUSTOMIZED SETTINGPOLICE
STROBE
SLOW
STROBE
FAST
STROBE SOS
LIGHT PER100%10%20%30%40%50%60%70%80% USERDEFINED
OUTPUT LM930 93 186279372465558651744 USERDEFINED
RUNTIME INDOOR STATIC TESTING AT 28ºC MAX OUTPUT 4.3 43 21.514.310.758.67.26.15.4>4.3
RANGE M OVER 150 METERS
MAXIMUM INTENSITY 5625 CD
WATERPROOF RATING IPX4
ANTIDROP 1M
DIMENSION30 MM HEAD DIAMETER
BATTERY 1 X 18650 BATTERY
WEIGHT 140 G EXCLUDING BATTERY
NOTE: THE ABOVE PARAMETERS ARE TESTED BY USING 1 PCS 3400 MAH 18650 LIION BATTERY
* PHOTOS ARE FOR REFERENCE ONLY, PRODUCTS IN KIND PREVAIL!
SWITCH
ADJUSTMENT
DIRECTIONHEAD
ADJUSTMENT
DIRECTION
ADJUSTMENT
BUCKLE
BATTERY HOLDER
18650
HEAVY DUTY
ELASTIC FABRIC
5.5 DC PLUG CABLE