Ferei HL40AAII User manual

FEATURES
1 Focusing LED headlamp.
2 Zoom-able head for spot and flood beam.
3 Cool or neutral white LED version available.
4 IPX4 Water resistant.
5 1000 lumens for 16 hours.
6 8 Selectable brightness levels from 10% to 80%.
7 4 selectable blinking modes: police blinking, slow blinking, quick
blinking, and SOS.
8 Smart IC motherboard provides multiple brightness settings,
and prevents overheat, over discharge or damages caused by polar
reversing.
9 Battery level indicating at 20% capacity.
10 Elastic bungee headband capable of length adjustment, providing
best fit and comfort for user.
11 Optional Diffuser and USB cable charger available.
12 Optional BP2836B, BP4836B and BP6836B for longest runtime each
8.6 hours, 17.2 hours and 25.8 hours on High.
GENERAL USAGE
1 Briefly press the rubber switch to turn the HL40AAII on/off.
2 The HL40AAII provides three lighting options:
•Maximum brightness: 100% output.
•Custom brightness: eight selectable modes ranging from 10% to
80% output.
•Strobe / SOS: police strobe, slow strobe, rapid strobe and SOS.
3 Operating Instruction
•To turn the HL40AAII on, briefly press the rubber switch. The default
setting is maximum brightness (100% output).
•To access custom brightness mode: with the HL40AAII turned on
(in either max or custom mode), hold the switch down for more than
2 seconds and the HL40AAII will cycle through 8 levels of output.
When a desired output is displayed simply release the button to set
the brightness.
•The HL40AAII has 3 hidden strobe modes and 1 SOS mode. To access
these modes simply hold down the power button for 2 seconds with
the unit turned off and release. To cycle to the next strobe / SOS
mode once again hold for 2 seconds and release. To exit strobe /
SOS mode simply press the switch once (turns the HL40AAII off).
The brightness level of strobe / SOS mode is determined by the
brightness set in custom mode.
4 50% battery warning: When battery capacity reaches 50%, the
HL40AAII will blink twice quickly to indicate battery status.
5 Low battery warning: When the battery capacity gets very low
(approx. 20%), the HL40AAII will emit 10 successive blinks in 8 seconds.
This is a reminder that the battery should be recharged or replaced.
6 Reverse polarity protection: When a battery is inserted incorrectly,
a special protection circuit will activate and automatically prevent
operation to ensure the safety of the HL40AAII and its user.
7 The HL40AAII is also designed with intelligent over-discharge
detection. If battery voltage reaches a critical lower limit, the HL40AAII
will automatically turn off, at which time the battery should be
recharged as soon as possible. Over-discharge of 18650 cells can cause
irreversible damage to the battery and in extreme cases, cause the
battery to inflate and / or emit a harmful gas. It is for this reason that
the HL40AAII is designed to operate only with 18650 batteries that are
above the lowest acceptable voltage limit.
STRETCH THE ROTATION HEAD PART TO ADJUST THE BEAM SIZE AND FOCUS SPOT
DIAGRAM
INSTALL AND REMOVE THE BATTERY BOX
AA BATTERY BOX INSTRUCTIONS
USER MANUAL
Focusing
LED Headlamp
HL40AAII
UNSCREW THE NUT BOTH NUTS ARE UNSCREW REMOVE THE SCREW CASE FROM
BATTERY BOX
INSET 3PCS 1.5V AA BATTERY
WITH THE CORRECT POLAR IN AA
BATTERY BOX
PUT THE SCREW CASE IN THE RIGHT
DIRECTION
SCREW UP BOTH NUTS ON AA BOX
TWO RUBBER BELTS TO TIGHTEN
ON AA BOX
CONNECT THE 5.5DC PLUG OF HEADLAMP AND THE 5.5 DC JACK
OF AA BOX, AND THEN SCREW UP THE HOLDER
THE DIRECTION OF DC JACK FOR
AA BATTERY BOX SHOULD BE TO
SWITCH BOX OF HEADLAMP
PUT THE AA BOX THRU THE RUBBER
BELT
ADJUSTMENT BUCKLE
NYLON ELASTIC BAND
HEAD
LED
ADJUSTMENT
DIRECTION
SWITCH
5.5 DC PLUG CABLE
BATTERY BOX 3*AA
* PHOTOS ARE FOR REFERENCE ONLY, PRODUCTS IN KIND PREVAIL!
ZOOM IN ZOOM OUT

USER MANUAL
Patented product, counterfeiting not allowed.
Shenzhen FEREI Lighting Co., Ltd.
3rd Industrial Zone, Xiakeng Village, Tongle, Longgang District, Shenzhen 518116, China.
TEL: [phone]
FAX: [phone].
E-mail: [e-mail] •Website: www.ferei.com
HL40AA II  PRODUCT SPECIFICATIONS
LED CREE XML2 COOL WHITE
ANSI/FSC MAX CUSTOMIZED SETTING POLICE
STROBE
SLOW
STROBE
FAST
STROBE SOS
LIGHT PER 100% 10% 20% 30% 40% 50% 60% 70% 80% USERDEFINED
OUTPUT LM 1000 100 200 300 400 500 600 700 800 USERDEFINED
RUNTIME H 16 160 80 57 40 32 27 23 20 >16
RANGE M OVER 200 METERS
MAXIMUM
INTENSITY 23256 CD
LED CREE XML2 NEUTRAL WHITE
ANSI/FSC MAX CUSTOMIZED SETTING POLICE
STROBE
SLOW
STROBE
FAST
STROBE SOS
LIGHT PER 100% 10% 20% 30% 40% 50% 60% 70% 80% USERDEFINED
OUTPUT LM 930 93 186 279 372 465 558 651 744 USERDEFINED
RUNTIME H 16 160 80 53 40 32 27 23 20 >16
RANGE M OVER 150 METERS
MAXIMUM
INTENSITY 5625 CD
WATERPROOF
RATING IPX4
ANTIDROP 1M
DIMENSION 30 MM HEAD DIAMETER
BATTERY 3 X AA BATTERIES
WEIGHT 168 G EXCLUDING BATTERY
NOTE: THE ABOVE PARAMETERS WERE TESTED BY USING THE AA LR6
HIGH POWER CAPACITY BATTERY
INTELLIGENT TEMPERATURE CONTROL INSTRUCTIONS
This product is designed with a temperature control circuit.
The LED is a heating device that is sensitive to temperatures,
especially high levels of power and brightness. High temperatures
will easily damage or shorten the life of the LED. Ferei designs its
products with an intelligent temperature-control circuit. It measures
the temperature within the LED filament. As the structure of the
lamp differs, the thermal conductivity of the entire lamp is not the
same. In general, the constant surface temperature of the lamp is
50˚C to 60˚C. When it exceeds its programmed temperature, it will
automatically reduce its power to cool down , and the brightness
decreases by small steps. After cooling-down (provided that battery
voltage is sufficient) the power with brightness increases again.
The process of improving its brightness is relatively discrete and will
not produce a flashing effect.
This stepping goes cyclically to maintain the user's safety and the
light's functionality. In conditions of good air-cooling the lamp
delivers light without stepping down even in high levels brightness
mode. There are no preset timers for stepping, but real-time active
temperature measurements, So the actual runtime of the lamp base
on active temperature control to faster or slower battery discharge,
may be slightly longer or shorter runtime than the lamp of data
provided .
WARM TIPS
In order to avoid accidents, please pay attention to the following
tips:
•Never use damaged, discolored or leaking batteries.
•Never use batteries with a damaged sleeve or foil covering.
•Always use 18650 batteries with safety certificates.
•If the light gets unusually hot when in use, turn it off and check
battery appearance.
•Never store the battery into the battery holder.
•Recharging is finished when the LED indicator turns to green.
•The battery remains at a normal temperature during
recharging. If it gets unusual hot, stop recharging and take the
battery out.
•Do not dissemble the charger kit by yourself if the battery
couldn’t be recharged.
•The battery can be used at any time once being recharged. If
it is left unused for long periods, it should be recharged for 4
hours every three months. After being charged they should be
slightly discharged for 10-20 minutes before storage.
•Be sure to always recharge the battery in a safe place and do
not leave unattended while charging.
MAINTENANCE
1 Wipe the glass lens with a soft cloth at regular intervals to
ensure maximum light transmittance (avoid using corrosive
detergents).
2 Ensure the cable plug and inside of the battery box remain free
of dirt and debris.
3 Unplug the cable from the battery box when unused for
extended periods.
WARNING
•It is a lighting tool, not a toy. Keep it away from children.
•Should not be aimed directly at the eyes of humans or animals
•Do not place the light face / lens down when turned on.
•The surface of the flashlight may become hot during extended use.
•Do not dismantle or dissemble any structural parts of the light, especially
the seal parts.
•Dry the light surface with soft cloth immediately after exposure to water or
any corrosive substance.
•Always remove batteries during long periods of inactivity (more than 30
days).
•Ferei reserves the right of interpretation of this manual.
Focusing
LED Headlamp
HL40AAII