FIBARO FGPB-101-5 User manual

FIBARO BUTTON
FGPB-101
CONTENTS
#1: Description and features 4
#2: Basic activation 5
#3: Adding/removing the device 6
#4: Operating the device 7
#5: Associations 8
#6: Advanced parameters 9
#7: Specications 13
#8: Regulations 14
OPERATING
MANUAL EN
v1.1

3
Important safety information
Read this manual before attempting to install the device!
Failure to observe recommendations included in this manual
may be dangerous or cause a violation of the law. The manufacturer,
Fibar Group S.A. will not be held responsible for any loss or damage
resulting from not following the instructions of operating manual.
!
General information about
the FIBARO System
FIBARO is a wireless smart home automation system, based on the
Z-Wave protocol. All of available devices can be controlled through
a computer (PC or Mac), smartphone or tablet. Z-Wave devices are
not only receivers, but can also repeat the signal, increasing the
Z-Wave network’s range. It gives advantage over traditional wireless
systems that require direct link between transmitter and receiver, as
a result the construction of the building could aect network’s range
negatively.
Every Z-Wave network has its unique identication number (home
ID). Multiple independent networks can exist in the building without
interfering. Transmission security of FIBARO System is comparable to
wired systems.
Z-Wave technology is the leading solution in smart home automation.
There is a wide range of Z-Wave devices that are mutually
compatible, independently of manufacturer. It gives the system the
ability to evolve and expand over time. For more information visit:
www.baro.com.

4
DESCRIPTION AND FEATURES
Main features of FIBARO Button:
• Compatible with any Z-Wave or Z-Wave+ Controller,
• Supports Z-Wave network Security Mode with AES-128 encryption,
• Completely wireless with battery power and Z-Wave
communication,
• May be installed anywhere in your home,
• Extremely easy installation - simply add and put on desired surface,
• Many colour variations: black, white, red, green, blue, yellow,
orange and brown.
FIBARO Button is a compact, battery-powered, Z-Wave Plus
compatible device. It allows you to control devices through the
Z-Wave network and run various scenes dened in FIBARO System.
Dierent actions may be triggered with one to ve clicks or by holding
the button down. In panic mode, each press of the button results in
triggering the FIBARO Alarm.
With its small design and wireless communication, the FIBARO Button
can be conveniently mounted on any surface and in any position or
location at home, e.g. beside the bed or under the desk.
#1: Description and features
FIBARO Button is a fully
compatible Z-Wave PLUS device.
NOTE
This device may be
used with all de-
vices certied with
the Z-Wave Plus cer-
ticate and should be
compatible with such
devices produced by
other manufacturers.
i
NOTE
Z-Wave Controller
must support Z-Wave
Security Mode in
order to fully utilize the
product.
i

5
BASIC ACTIVATION
#2: Basic activation
1. Press and turn the button counter-clockwise to open the casing.
2. Remove the paper strip underneath the battery.
3. Press and turn the button clockwise to close the casing.
4. Place the device within the direct range of your Z-Wave controller.
5. Set the main controller in (security/non-security) add mode (see
the controller’s manual).
6. Click the button 6 times at least.
7. Wait for the device to be added into the system, successful adding
will be conrmed by the controller.
8. Install the device in desired location using the attached
self-adhesive pad.
9. Click the button 4 times to wake it up.

6
ADDING/REMOVING THE DEVICE
Adding (Inclusion) - Z-Wave device learning mode, allowing to add
the device to existing Z-Wave network.
To add the device to the Z-Wave network:
1. Place the Button within the direct range of your Z-Wave controller.
2. Set the main controller in (Security/non-Security) add mode (see
the controller’s manual).
3. Click the Button at least six times.
4. Wait for the adding process to end.
5. Successful adding will be conrmed by the Z-Wave controller’s
message.
Removing (Exclusion) - Z-Wave device learning mode, allowing to
remove the device from existing Z-Wave network.
To remove the device to the Z-Wave network:
1. Place the Button within the direct range of your Z-Wave controller.
2. Set the main controller in remove mode (see the controller’s
manual).
3. Click the Button at least six times.
4. Wait for the removing process to end.
5. Successful removing will be conrmed by the Z-Wave controller’s
message.
#3: Adding/removing the device
NOTE
Adding in Security
Mode must be per-
formed up to 2 meters
from the controller.
i
NOTE
Removing the Button
from the Z-Wave net-
work restores all the
default parameters of
the device.
i
NOTE
In case the device is
not added, repeat the
adding procedure.
i

7
OPERATING THE DEVICE
#4: Operating the device
Waking up the device:
The Button needs to be woken up to receive information about the
new conguration from the controller, like parameters and associa-
tions.
Click the Button 4 times to wake it up.
Operating the Button:
1 click:
2 clicks:
3 clicks:
4 clicks:
5 clicks:
6 or more
clicks:
Hold:
Release:
send action to associated devices (switch on/o by de-
fault) and/or trigger a scene
send action to associated devices (switch on maximum
level by default) and/or trigger a scene
send action to associated devices (no action by default)
and/or trigger a scene
wake the device up and/or trigger a scene
start reset procedure (press and hold for 5s to conrm)
and/or trigger a scene
learning mode (adding/removing)
send action to associated devices (start level change up/
down) and/or trigger a scene
send action to associated devices (stop level change)
and/or trigger a scene
Scene ID:
Every action with the
Button is send to the main
controller with Scene ID
equal to 1. Controller recog-
nizes type of action using the
attribute assigned to it.
Reset procedure of the Button:
Reset procedure allows to restore the device back to its factory set-
tings, which means all information about the Z-Wave controller and
user conguration will be deleted. In order to reset the device:
1. Click the Button exactly ve times.
2. Press and hold the Button for at least 5 seconds.
Action Attribute
1 click Key Pressed 1 time
2 clicks Key Pressed 2 times
3 clicks Key Pressed 3 times
4 clicks Key Pressed 4 times
5 clicks Key Pressed 5 times
Hold Key Held Down
Release Key Released
NOTE
If notications are
enabled, each press
of the button results
in sendng a com-
mand (Notication
Type=HOME_SECURI-
TY, Event=Intrusion,
Unknown Location).
i
NOTE
Resetting the device is
not the recommend-
ed way of removing
the device from the
Z-Wave network. Use
reset procedure only
if the primary con-
troller is missing or
inoperable. Certain
device removal can be
achieved by the pro-
cedure of removing.
i

8
ASSOCIATIONS
#5: Associations
The Button provides the association of four groups:
1st association group – “Lifeline” reports the device status and al-
lows for assigning single device only (main controller by default).
2nd association group – “On/O” is assigned to clicking the button
and is used to turn on/o associated devices.
3rd association group – “Dimmer” is assigned to holding the but-
ton and is used to change level of associated devices.
4th association group –“Alarm“ is assigned to clicking and/or hold-
ing the button (triggers are dened in parameter 30) and is used to
send alarm frames to associated devices.
To add an association (using the Home Center controller):
1. Go to device options by clicking the icon:
2. Select the„Advanced” tab.
3. Click the “Setting Association” button.
4. Specify to which group and what devices are to be associated.
5. Save the changes.
6. Wake up the device manually to conrm changes (4 clicks).
FIBARO Button in 2nd, 3rd and 4th group allows to control 5 regular
or multichannel devices per an association group, with the exception
of “LifeLine” that is reserved solely for the controller and hence only 1
node can be assigned.
It is not recommended to associate more than 10 devices in general,
as the response time to control commands depends on the number of
associated devices. In extreme cases, system response may be delayed.
Association (linking devices) - direct control of other devices within
the Z-Wave system network e.g. Dimmer, Relay Switch, Roller Shutter
or scene (may be controlled only through a Z-Wave controller).
NOTE
Association ensures
direct transfer of
control commands
between devices, is
performed without
participation of the
main controller and
requires associated
device to be in the di-
rect range.
i
NOTE
Increasing number
of associations will
increase battery con-
sumption resulting in
shorter battery life.
i
NOTE
The device supports
the generic Z-Wave
command class "Basic"
but will ignore any SET
or GET commands and
will not respond with a
Basic Report.
i

9
ADVANCED PARAMETERS
#6: Advanced parameters
1. Scenes sent to the controller
This parameter determines which actions result in sending scene IDs
and attributes assigned to them.
Available settings: 1- Key Pressed 1 time
2- Key Pressed 2 times
4- Key Pressed 3 times
8- Key Pressed 4 times
16 - Key Pressed 5 times
32 - Key Held Down
64 - Key Released
Default setting: 127 (all) Parameter size: 1[byte]
The Button allows to customize its operation to user’s needs. The set-
tings are available in the FIBARO interface as simple options that may
be chosen by selecting the appropriate box.
In order to congure the Button (using the HC controller):
1. Go to the device options by clicking the icon:
2. Select the„Advanced” tab.
3. Modify values of chosen parameters.
4. Save the changes.
5. Wake up the device manually to conrm changes (4 clicks).
Wake up interval
Available settings: 0or 3600-64800 (in seconds, 1h - 18h)
Default setting: 0
The Button will wake up at each dened time interval and always try to
connect with the main controller. After successful communication at-
tempt, the device will update conguration parameters, associations
and settings and then will go into Z-Wave communication standby.
After failed communication attempt (eg. no Z-Wave range) the device
will go into Z-Wave communication standby and retry to establish
connection with the main controller after the next time interval.
Setting wake up interval to 0 disables sending Wake Up notication
to the controller automatically. Wake up may be still performed man-
ually by clicking the Button 4 times.
NOTE
Values of parameter
1 may be combined,
e.g. 1+2=3 means that
scenes will be sent
after pressing the but-
ton once or twice.
i
NOTE
Longer wake up time
interval means less
frequent communica-
tion and thus a longer
battery life.
i

10
ADVANCED PARAMETERS
NOTE
Setting parameters
11, 13, 15, 21, 23 and
25 to appropriate val-
ue will result in:
1-99 - forcing level of
associated devices
255 - setting associat-
ed devices to the last
remembered state or
turning them on
i
3. Associations in Z-Wave network Security Mode
This parameter denes how commands are sent in specied associa-
tion groups: as secure or non-secure. Parameter is active only in Z-Wave
network Security Mode. It does not apply to 1st„Lifeline” group.
Available settings: 1- 2nd group sent as secure
2- 3rd group sent as secure
4- 4th group sent as secure
Default setting: 7 (all) Parameter size: 1[byte]
10. Key Pressed 1 time – command sent to 2nd association group
This parameter denes commands sent to devices associated in 2nd
association group after a single click.
Available settings: 0- no action
1- SWITCH ON
2- SWITCH OFF
3- SWITCH ON/OFF – alternately
Default setting: 3Parameter size: 1[byte]
11. Key Pressed 1 time – value of SWITCH ON command sent to
2nd association group
This parameter denes value of SWITCH ON command sent to devices
in 2nd association group after a single click.
Available settings: 1-255 - sent value
Default setting: 255 Parameter size: 2[bytes]
12. Key Pressed 2 times – command sent to 2nd association group
This parameter denes commands sent to devices associated in 2nd
association group after a double click.
Available settings: 0- no action
1- SWITCH ON
2- SWITCH OFF
3- SWITCH ON/OFF – alternately
Default setting: 1Parameter size: 1[byte]
13. Key Pressed 2 times – value of SWITCH ON command sent to
2nd association group
This parameter denes value of SWITCH ON command sent to devices
in 2nd association group after a double click.
Available settings: 1-255 - sent value
Default setting: 99 Parameter size: 2[bytes]
NOTE
Values of parameter
3 may be combined,
e.g. 1+2=3 means that
2nd & 3rd group are
sent as secure.
i

11
ADVANCED PARAMETERS
14. Key Pressed 3 times – command sent to 2nd association group
This parameter denes commands sent to devices associated in 2nd
association group after a triple click.
Available settings: 0- no action
1- SWITCH ON
2- SWITCH OFF
3- SWITCH ON/OFF – alternately
Default setting: 0Parameter size: 1[byte]
15. Key Pressed 3 times – value of SWITCH ON command sent to
2nd association group
This parameter denes value of SWITCH ON command sent to devices
in 2nd association group after a triple click.
Available settings: 1-255 - sent value
Default setting: 255 Parameter size: 2[bytes]
20. Key Pressed 1 time – command sent to 3rd association group
This parameter denes commands sent to devices associated in 3rd
association group after a single click.
Available settings: 0- no action
1- SWITCH ON
2- SWITCH OFF
3- SWITCH ON/OFF – alternately
Default setting: 3Parameter size: 1[byte]
21. Key Pressed 1 time – value of SWITCH ON command sent to
3rd association group
This parameter denes value of SWITCH ON command sent to devices
in 3rd association group after a single click.
Available settings: 1-255 - sent value
Default setting: 255 Parameter size: 2[bytes]
22. Key Pressed 2 times – command sent to 3rd association group
This parameter denes commands sent to devices associated in 3rd
association group after a double click.
Available settings: 0- no action
1- SWITCH ON
2- SWITCH OFF
3- SWITCH ON/OFF – alternately
Default setting: 1Parameter size: 1[byte]

12
ADVANCED PARAMETERS
23. Key Pressed 2 times – value of SWITCH ON command sent to
3rd association group
This parameter denes value of SWITCH ON command sent to devices
in 3rd association group after a double click.
Available settings: 1-255 - sent value
Default setting: 99 Parameter size: 2[bytes]
24. Key Pressed 3 times – command sent to 3rd association group
This parameter denes commands sent to devices associated in 3rd
association group after a triple click.
Available settings: 0- no action
1- SWITCH ON
2- SWITCH OFF
3- SWITCH ON/OFF – alternately
Default setting: 0Parameter size: 1[byte]
25. Key Pressed 3 times – value of SWITCH ON command sent to
3rd association group
This parameter denes value of SWITCH ON command sent to devices
in 3rd association group after a triple click.
Available settings: 1-255 - sent value
Default setting: 255 Parameter size: 2[bytes]
29. Key Held Down – command sent to 3rd association group
This parameter denes commands sent to devices associated in 3rd
association group after holding the button down.
Available settings: 0- no action
1- START LEVEL CHANGE UP (brightening)
2- START LEVEL CHANGE DOWN (dimming)
3- START LEVEL CHANGE UP/DOWN (brighten-
ing/dimming) – alternately
Default setting: 3Parameter size: 1[byte]
30. Alarm frame triggers
Parameter determines which actions result in sending alarm frames
to 4th association group.
Available settings: 1- Key Pressed 1 time
2- Key Pressed 2 times
4- Key Pressed 3 times
8- Key Pressed 4 times
16 - Key Pressed 5 times
32 - Key Held Down
64 - Key Released
Default setting: 127 (all) Parameter size: 1[byte]
NOTE
Values of parame-
ter 30 may be com-
bined, e.g. 1+2=3
means that alarm
frames will be sent
after pressing the but-
ton once or twice.
i

13
SPECIFICATIONS
Battery type:
Battery life:
Operating temperature:
EU standards compliance:
Radio protocol:
Radio frequency:
Range:
Dimensions
(diameter x height):
ER14250 ½AA 3.6V
est. 2 years (with default settings and
max. 10 pushes per day)
0 - 40°C (32 - 104°F)
RoHS 2011/65/EU
R&TTE 1999/5/EC
Z-Wave (500 series chip)
868.4 or 869.8 MHz EU;
908.4, 908.42 or 916.0 MHz US;
921.4 or 919.8 MHz ANZ;
869.0 MHz RU;
up to 50m (164 ft) outdoors
up to 40m (131 ft) indoors
(Depending on terrain and building
structure)
46 x 34 mm
(1.81" x 1.34")
#7: Specications
CAUTION
Using batteries other
than specied may
result in explosion.
Dispose of properly,
observing environ-
mental protection
rules.
!
NOTE
Radio frequency of
individual device
must be same as your
Z-Wave controller.
Check information
on the box or consult
your dealer if you are
not sure.
i

14
REGULATIONS
#8: Regulations
This device complies with Part 15 of the FCC Rules
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including inter-
ference that may cause undesired operation. This equipment has been
tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada (IC) Compliance Notice
This device complies with Industry Canada license-exempt RSSs. Oper-
ation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, in-
cluding interference that may cause undesired operation of the device.
Cet appareil est conforme aux normes d’exemption de licence RSS d’In-
dustry Canada. Son fonctionnement est soumis aux deux conditions
suivantes : (1) cet appareil ne doit pas causer d’interférence et (2) cet
appareil doit accepter toute interférence, notamment les interférences
qui peuvent aecter son fonctionnement.
Legal Notices
All information, including, but not limited to, information regarding the
features, functionality, and/or other product specication are subject
to change without notice. Fibaro reserves all rights to revise or update
its products, software, or documentation without any obligation to no-
tify any individual or entity.
FIBARO and Fibar Group logo are trademarks of Fibar Group S.A. All
other brands and product names referred to herein are trademarks of
their respective holders.

15
REGULATIONS
Note
Changes and modications not expressly approved by the manufactu-
rer or registrant of this equipment can void your authority to operate
this equipment under Federal Communications Commission’s rules.
DGT Warning Statement
Article 12
Without permission, any company, rm or user shall not alter the fre-
quency, increase the power, or change the characteristics and func-
tions of the original design of the certied lower power frequency elec-
tric machinery.
Article 14
The application of low power frequency electric machineries shall not
aect the navigation safety nor interfere a legal communication, if an
interference is found, the service will be suspended until improvement
is made and the interference no longer exists.
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用
者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現
有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性
電機設備之干擾。
Declaration of conformity
Hereby, Fibar Group S.A. declares that FIBARO Button is in compliance
with the essential requirements and other relevant provisions of Di-
rective 1999/5/EC.