Fibaro Fgbwhwpf-102 User manual

CONTENTS

#1: Description and features 3

#2: Pairing the accessory 4

#3: Reset 5

#4: Functionality 6

#5: Wi-Fi 8

#6: Congurable parameters 9

#7: Specications 10

#8: Regulations 11

OPERATING

MANUAL EN

FIBARO WALL PLUG

FGBWHWPE-102/FGBWHWPF-102

v1.0

Important safety information

Read this manual before attempting to install the device!

Failure to observe recommendations included in this manual

may be dangerous or cause a violation of the law. The manu-

facturer, Fibar Group S.A. will not be held responsible for any

loss or damage resulting from not following the instructions of

operating manual.

HomeKit technology

Apple HomeKit technology provides an easy, secure way to control

HomeKit-enabled accessories using Siri on your iPhone, iPad, or iPod

touch.

After installing your FIBAROWall Plug, congure it from a compatible

app with just a few simple steps.

You can even create your own custom scenes to control your home

settings. For example, you can create a scene to automatically turn

o the lights, lock your doors, close the garage door, and set the

thermostat to the desired temperature in just one step.

To control this HomeKit-enabled accessory, iOS 10 or later is

recommended.

Controlling this HomeKit-enabled accessory auto-

matically and away from home requires an Apple TV

with tvOS 10 or later or an iPad with iOS 10 or later set up as a

home hub.

This product is intended for indoor use only in dry locations.

Do not use in damp or wet locations, near a bathtub, sink,

shower, swimming pool, or anywhere else where water or

moisture are present.

Caution!

To avoid risk of electrical shock, do not operate the device with

wet or moist hands.

Do not plug one Wall Plug into another Wall Plug.

Note

Socket used for the Wall Plug should be easily accessible.

DESCRIPTION AND FEATURES

Main features of FIBARO Wall Plug:

• Compatible with Apple HomeKit technology,

• Wi-Fi for wireless communication,

• Detects if electrical device is connected to it,

• Measures active power consumption,

• Measures energy consumption,

• Easy installation,

• Indicates state and consumption using multicolor LED ring.

FIBARO Wall Plug is a HomeKit-enabled smart plug using Wi-Fi®

connection and Bluetooth® low energy wireless technology.

This remotely controlled outlet adapter is equipped with an active

power and energy metering function.

It uses a LED ring to visualize current consumption and status.

The Wall Plug may be operated using the button on the casing or via

an iOS mobile app through Wi-Fi.

#1: Description and features

PAIRING THE ACCESSORY

#2: Pairing the accessory

1. Open the Settings app on your iOS device.

2. Go to the Wi-Fi section, turn the Wi-Fi on and connect to your pre-

ferred Wi-Fi network.

3. Go to the Bluetooth® section, and turn the Bluetooth® on.

4. Plug the Wall Plug into an electrical socket.

5. The LED ring will be ashing yellow when ready for conguration.

6. Open a HomeKit compatible app of your choosing on your iOS

device.

7. Open pairing window in your HomeKit app to detect available

accessories.

8. Choose Wall Plug you wish to pair.

9. When prompted, allow the Wall Plug to connect to your Wi-Fi

network.

10. Wait until the LED ring starts ashing violet.

11. You can identify it - Wall Plug will triple blink blue 3 times.

12. Find HomeKit Setup Code on the last page of Quick Start Guide

included in the box that looks like this:

13. Start pairing with your HomeKit app.

14. Point your iOS device’s camera at the Setup Code to scan it or en-

ter the Setup Code manually.

15. If entered Setup Code is valid, the device will complete the setup

process.

16. Follow instructions displayed in the application.

XXX-XX-XXX

NOTE

Remember to keep

your HomeKit Setup

Code in safe place. You

may need it in case of

re-pairing.

Backup Setup Code is

printed on the label

of the accessory, but

requires entering it

manually.

RESET

Resetting the Wall Plug to factory defaults:

Reset procedure allows to restore the accessory back to its factory

settings including HomeKit pairing.

1. Make sure the accessory is powered.

2. Press and hold the button.

3. When the LED ring glows yellow, release the button.

4. Immediately click the button again to conrm.

5. Accessory will glow red to conrm reset.

6. Delete the accessory from the app before pairing it again.

#3: Reset

Button

FUNCTIONALITY

#4: Functionality

Turning ON/OFF electrical devices:

The Wall Plug can turn ON/OFF connected electrical device either

through iOS mobile app or button.

Multicolor LED ring:

The LED ring of the Wall Plug glows when device is turned ON and dis-

plays current active power consumption. Additionally LED ring allows

to navigate the built-in menu.

Menu:

The Wall Plug can be operated using the built-in menu.

To enter and navigate the menu:

1. Press and hold the button.

2. Release the button, when the LED ring glows with desired color:

• VIOLET - Wi-Fi range test

• RED - reset Wi-Fi settings

• GREEN - reset energy counter

• YELLOW - factory reset

3. Immediately click the button again to conrm selection.

Disabling the LED ring backlight:

1. Press and hold the button for about 3 seconds.

2. Release the button when the LED ring starts pulsing white.

To restore the LED ring backlight perform above procedure again.

Active power metering:

The Wall Plug measures current active power consumption of con-

nected device and reports it to your iOS device. Measured value is

indicated with color of the LED ring.

Active power measuring accuracy is ±1% for loads greater than 5W.

Energy metering:

The Wall Plug counts energy consumed by connected device and re-

ports accumulated value to your iOS device.

To reset energy counter:

1. Press and hold the button.

2. When the LED glows green, release the button.

3. Immediately click the button again to conrm.

FUNCTIONALITY

NOTE

* Functionality availa-

ble only in Fibaro for

HomeKit app.

Plug insertion detection:

The Wall Plug detects if any device is plugged into it and reports it to

your iOS device.

Overload Control*:

Functionality allows to switch o connected load after 4 seconds

from exceeding the power set by the user in Fibaro for HomeKit app.

Power Change Notication*:

Minimum and maximum allowed power consumption may be de-

ned by the user in Fibaro for HomeKit app. Exceeding any of these

values results in sending a notication.

Timer Switch*:

Functionality allows to set time (in Fibaro for HomeKit app) after

which connected load will be automatically turned on/turned o.

Timer will start after changing the ON/OFF state to opposite (through

the app or connected wall switch). If the device state was changed

before expiring of the set time, the counter will reset.

It is possible to use both Turn ON and Turn OFF functionality - it will

result in cyclic load control.

WIFI

Wi-Fi range test:

The Wall Plug can measure Wi-Fi signal strength and indicates it with

color of LED ring:

• Green – good (≥ -45dBm)

• Yellow – fair (≥ -70dBm, < -45dB)

• Red – weak (< -70dBm)

To start range test:

1. Press and hold the button.

2. When the LED glows violet, release the button.

3. Immediately click the button again to conrm.

4. LED ring will indicate signal strength with color.

5. Range test will be disabled after pushing the button.

Resetting Wi-Fi settings:

The Wall Plug allows to reset its Wi-Fi settings and get new setting

from your iOS device.

To reset Wi-Fi settings:

1. Press and hold the button.

2. When the LED glows red, release the button.

3. Immediately click the button again to conrm.

4. LED ring will glow yellow for 30 minutes, while waiting for new

settings from iOS device.

#5: Wi-Fi

CONFIGURABLE PARAMETERS

#6: Congurable parameters

1. Color of LED ring

This parameter allows to choose color of LED ring when device is ON.

Available settings: 0– color dependent on measured active power*

1– color dependent on active power measure-

ments with smooth transition between colors*

2– white, 3– red, 4– green, 5– blue, 6– yellow,

7– cyan, 8– magenta

9- LED ring disabled

Default setting: 1 (color dependent on measured active power

with smooth transition between colors)

2. Measured power for blue LED ring color

This parameter allows to set power value for blue backlight of LED ring.