Fiberweb Typar pathmat User manual

™

PathMat

InstallatIon InstructIons

Fig. 3 - Cover ends with sand to prevent tripping

small weavIng

rIbs face up

Fig. 1 - Unroll mat

Fig. 2 - anChor the pathmat end with U-pins

PathMat

SPECIFICATION &

INSTALLATION

GUIDANCE

The Fiberweb PathMat Beach Access Mat is a highly portable roll out mat perfect

for establishing pedestrian, wheelchair and maintenance access paths over sandy

beaches. The elastomeric material allows for a draping effect over undulating

ground while the oscillated mesh structure provides lateral rigidity for optimal

access. The unique features of the mat make it a premier beach access mat that is

environmentally friendly and cost effective.

Installation Methods

1. Prepare the surface where the PathMat Beach Access Mat will be applied

by raking the beach debris and foreign objects, removing from the area.

The surface should be as smooth and at as possible to ensure optimal

wheelchair accessibility.

2. Unroll the PathMat Beach Access Mat fully. Install the mat with the large ribs

facing down and the small weaving ribs facing up. (Fig. 1)

3. Where the PathMat Beach Access Mat meets with a permanent trail structure

the mat end should be placed parallel to the edge so there is no gap. Set the

mat ush or below the permanent path to eliminate a tripping hazard. This

can be achieved by digging a one to two inch trench. Allow the end of the mat

to fold into this trench. The PathMat can be cut if the desired path is to move

at an angle away from the permanent path.

4. Anchor the PathMat end using four steel U-Pins (g. 2.) The U-Pins should be

six inches wide and 16 inches deep for optimal anchoring. Install the pins in

the predened holes in the mat connector strip. The mats are supplied with a

connector strip on each end of the Path Mat.

5. Anchor the end moving onto the beach by digging a three inch trench. Fold

the end of the mat into the trench rmly securing this end with four U-pins.

6. Rake sand over the trench covering the end of the mat to prevent a tripping

hazard. (Fig. 3)

Connecting Multiple PathMat Sections

1. Prepare the extended access route site and installation of the rst mat as

outlined in steps one through four of the Installation Instructions above.

2. Connect the second mat by overlapping the connector strips, ensuring that

the anchoring holes are lined up so the U-pins anchor both mats securely

together.

3. Secure the mats with four pins at each seam to reduce the force on the

leading initial anchoring point.

4. Continue connecting mats for the length of the access route. Complete the

installation by securing the end of the nal PathMat section per steps four

through six of the installation instructions above.

™

PathMat

barefoot frIendly

easy InstallatIon

The access routes built utilizing the PathMat are ready for use immediately following installation. Please follow these maintenance

recommendations to ensure a long life and optimal performance of your PathMat Beach Access Mats.

Maintenance Recommendations

Note 1: In the case of a large storm or windy conditions, remove accumulated sand from the surface of the PathMat with a hand push

broom. A at shovel may be used in the case of excessive sand accumulation. Take care to not damage the mat when removing sand.

Note 2: In the event of movement and sifting, it is recommended that accumulated sand be removed from beneath the mat to reduce

the tension on the mat sections. Simply remove the pins and roll the mat backwards. Rake the sand at and reinstall the end per the

installation instructions.

Note 3: At no time in maintenance is it acceptable to use vehicular means to reposition or remove sand from the mats. This can cause

damage to the mat sections.

Note 4: Clean the mats with a pressure washing machine.

Please note that the information above is given as a guide only. Fiberweb cannot be liable for damage caused by incorrect installation of this product. Final

determination of the suitability of any information or material for the use contemplated and the manner of its use is the sole responsibility of the user and the user

must assume all risk and responsibility in connection therewith.

PATHMAT™ PRODUCT SPECIFICATIONS

PHYSICAL CHARACTERISTICS:

Structure Oscillated

Polymer Elastomeric

PE Blend

Color Light Blue

UV Stabilized Yes

NOMINAL DIMENSIONS:

Roll Width 5 feet

Roll Length 32.8 feet

Roll Weight 125.5 lbs.