Finelite HP-2 User manual

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
1
HP-2 Direct Starter/Independent Installation Instructions
© 2016 FI ELITE, I C. ALL RIGHTS RESERVED. Form 98234 V2. 11/16
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
GridBox™
Caddy Clip
Secure to Structure
(by others)
Power Cord
Safety Stop
Gripper
Feed Hole
Step 1
Install grippers onto threaded studs on both ends
of the luminaire.
GridBox™
Aircraft
Cable
Power
Cable
Canopy
Caddy Clip
Secure to Structure
(by others)
Step 2
Install GridBox™ and caddy clip onto ceiling grid, then canopies and aircraft cable assemblies. A. Align aircraft cables to grippers and insert on
both ends of the luminaire. Adjust pendant to proper height and level. Press down on top of gripper to release locking mechanism if needed.
Secure luminaire to structure using tie-wire (by others) according to code. B. End plates are adjustable for custom mounting locations.
Remove #8-18 x 1/4" screw (provided) from end plate, then slide end plate to desired location and reinstall #8-18 x 1/4" screw.
Step 4
Slide safety stop and safety crimp up to the aircraft cable within 9" of cable gripper. Trim excess cable and insert safety bar
assembly through feed hole. Turn power on to luminaire.
Step 3
Install power cable through canopy and into GridBox™. Make electrical connections in GridBox.
Aircraft Cable
Cable Bushing
Ceiling
Luminaire
Locate aircraft cables.
Gripper
Threaded
Stud
Power Cord
Press Down
Here to Release
Locking
Mechanism
Power
Cord
Gripper
Aircraft
Cable
GridBox™
Canopy
Power Feed
Threaded
Coupler
Aircraft
Cable
End Plate
#8-18 x 1/4" Screw
(provided)
A
B
0 - 10V
Dimming
Scan QR code for
helpful video(s)

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
1
HP-2 Direct Joiner/Ender Installation Instructions
© 2016 FINELITE, INC. ALL RIGHTS RESERVED. Form 98235 V2. 11/16
rotected by one or more US atents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Aircraft
Cable
Gripper
End Plate
Joiner/Ender
Diffuser
Step 1
Remove diffusers and set aside to prevent it from
getting dirty or damaged.
Joiner/Ender
Starter
Caddy Clip
Aircraft Cable
Step 2
Install caddy clip for joiner/ender. Install canopy, cable bushing and aircraft cable onto caddy clip.
Step 3
Install gripper onto end plate of luminaire
then install aircraft cable into gripper. Adjust
pendant to proper height and level.
Joiner Plate
Starter
Joiner/Ender
Safety
Stop
Step 4
Align starter and joiner/ender luminaires and slide luminaires together. Slide safety stop and safety crimp up to the aircraft
cable within 9" of cable gripper. Trim excess cable and insert safety bar assembly through feed hole.
Safety
Stop
Caddy Clip
Canopy
Cable Bushing
Aircraft Cable
Aircraft Cable
Cable Bushing
Ceiling
Luminaire
Locate aircraft cables.
0 - 10V
Dimming
Scan QR co e for
helpful vi eo(s)
Back Plates
Starter
Joiner/Ender
Step 5
Remove back plate clips (provided) to release back plates. We recommend using a
flat head screwdriver to get them loose. CAUTION: Do not lose these pieces.
Back Plate Clip

Note: All power connections to be installed to
local/national codes by a Certified Electrician.
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • [phone] • Fax: [phone] • www.finelite.com
2
HP-2 Direct Joiner/Ender Installation Instructions
© 2016 FINELITE, INC. ALL RIGHTS RESERVED. Form 98235 V2. 11/16
rotected by one or more US atents: 8915613; D702,391; D702,390; D700,732; D727,554 S; D727,550 S, D727,551 S
Starter
Joiner/Ender
Yoke Brackets
(provided) x 2
Joint Sleeve
#10-32 x 5/8" Screws
(provided) x 2
Joint Sleeve
Step 7
IMPORTANT STEP: Secure joint with two yoke brackets (provided) using #10-32 x 5/8"
screws (provided). CAUTION: When installed correctly these brackets will pull
luminaires together to make a tight joint. Do not over-tighten.
Diffuser
Starter
Joiner
Reinstall diffusers and turn power on to luminaire.
Starter
Joiner/Ender
Plug-Together Wiring
Step 8
Connect plug-together wiring.
Back Plates
Starter
Joiner/Ender
Step 6
Pivot Point
Slowly swing down back plates. CAUTION: Do not twist back plate when swinging own – it
will come out of the support extrusion. Note that the screw shown is the pivot point and the
back plate can be slid a few inches either way for ease of access to the driver space.
Back Plates
Starter
Joiner/Ender
Step 9
Replace back plates by holding them in their original position and pushing the clips back in. Make sure wire connections are
not pinched. (If 1 ft. back plate assembly is near joint, reconnect feed harness to LED board).
Back Plate Clip
Step 10
IMPORTANT STEP