Finelite Hp-2 User manual

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 1 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

Overview

Step 5

Joining Luminaires

Page 8

Step 1

Rough-Ins & Mounting Options

Pages 2-3

Step 2

Identification & Preparation

Page 4

Step 9

Closing Luminaires

Pages 12-13

Step 4

Mounting Starter

to Structure

Pages 6-7

Step 3

Opening Luminaires

Pages 5

Step 6

Securing Luminaire Joints

Page 9

Step 7

Joining Mitered Corners

Page 10

Step 8

Securing Corners Joints

Page 11

•This installation requires proper support as each luminaire is being installed.

•DO NOT attempt to join luminaires together on the floor. Damage may result

when lifted. Follow these instructions.

NOTE

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

Helpful Video

0-10V Dimming

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 2 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

Step 1 - Rough-Ins & Mounting Options

Rough-In Widths

Total Run Length

W

CONTINUED

X1 X2

Y2

L1

L2

Rough-In Lengths

Y1

Starter

ID: 1

Joiner

ID: 2

Ender

ID: 3

Z = Mounting Hole Location

(Does not include endcaps)

HP-2 5"

HP-4 6"

HP-6 6-1/2"

X= Luminaire section length (Does not include endcaps)

Y1 = Total run length of luminaire (Does not include endcaps)

Y2 = Total run length of luminaire (Does not include endcaps)

Z= Mounting hole location

Refer to Record Drawings and building plans to determine

exact mounting, suspension points, and power feed locations.

• Use rough-in Length & Width dimension and Record Drawings to determine rough-in measurements.

• Build wall/ceiling with rough-in according to rough-in dimensions.

• CRITICAL: Drywall or weak paneling must be secured to blocking (studs) around rough-in opening in

the wall/ceiling.

Spackle Flange (SF)

W

Visible Flange (VF)

W

* Tolerance +/- 1/16"

L1 & L2 = Total Run Rough-In Length*

Spackle Flange Visible Flange

L1 L2 L1 L2

HP-2 Y1 + 7/16" Y2 + 7/16" Y1 + 5/16" Y2 + 5/16"

HP-4 Y1 + 9/16" Y2 + 9/16" Y1 + 7/16" Y2 + 7/16"

HP-6 Y1 + 7/16" Y2 + 7/16" Y1 + 5/16" Y2 + 5/16"

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

Z

Endcap

W= Rough-In Width*

Spackle Flange Visible Flange

HP-2 3-1/8" 2-7/8"

HP-4 4-7/8" 4-1/4"

HP-6 6-1/8" 5-7/8"

* Tolerance +/- 1/16"

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 3 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

Step 1 - Rough-Ins & Mounting Options

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

1/4"-20 Washer & 1/4"-20 Nut

(by others)

1/4" Threaded Rod

(by others)

Drywall Ceiling/Wall Drywall Ceiling/Wall

Structure Support (by others)

1/4" Lag Bolt

(by others)

• Luminaire mounting holes sized for 1/4"-20 threaded rod.

• Refer to Record Drawings to determine mounting hole locations on luminaires and install threaded rods to structure.

• Distance from threaded rod to wall/ceiling surface1must be a minimum of 3-1/2".

• Refer to Record Drawings to determine mounting hole locations on luminaires and install support blocking² to structure.

• Distance from support block to wall/ceiling surface1must be a minimum of 4-1/8".

3-1/2" min. 4-1/8" min.

Support

Blocking2

(by others)

Support

Blocking2

(by others)

Mounting Options

Option 1 - Mount to Threaded Rod Option 2 - Mount to Structure

1/4"-20 Washer

(by others)

1/4"-20 Nut

(by others)

Mounting Option 1

Threaded Rod

(by others)

¹ Wall/ceiling surface = drywall, wood, concrete or masonry, metal panels, tile, etc.

² Support blocking = Wooden beams/studs, sheet metal framing beams, steel beams, concrete beams, etc. Use hardware appropriate to the beam material.

1/4"-20 Lag Bolt

(by others)

Mounting Option 2

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 4 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

HP-6 VF - 8'

ABC Corporation - A12345

HP-6-VF - 32' - S - 835 - F - 120V - SC - C1 - OBO

STARTER ID: 1 HP-6 VF - 16'

ABC Corporation - A12345

HP-6-VF - 32' - S - 835 - F - 120V - SC - C1 - OBO

JOINER ID: 2 HP-6 VF - 23'

ABC Corporation - A12345

HP-6-VF - 32' - S - 835 - F - 120V - SC - C1 - OBO

ENDER ID: 3

ABC Corporation - A12345

HP-6 VF - 32' - H - 835 - F - 120V - SC - C1

HP-6 VF - X'

ID: 1

STARTER

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

A. Identify Luminaires B. Remove Diffuser

Step 2 - Identification & Preparation

Kitted Hardware

• Identify all luminaires by their ID label that can be found on the box, the diffuser and inside the luminaire.

• NOTE: Exact location of labels in these areas may vary.

• Remove all luminaires from their box.

• Arrange luminaires in order according to ID# at their install locations.

• Refer to Record Drawings that can be found in the hardware kit.

• Carefully remove all diffusers, keeping them inside their protective bags.

• Set aside all diffusers to prevent from getting dirty or damaged.

• Ensure diffusers can be clearly identified back to its corresponding luminaire.

• CAUTION (Spackle Flange Only): Carefully remove "Mud Guards" and keep them as they will be reinstalled in Step 9, B.

Yoke Bracket

Part# 45042

#10-32 x 5/8" Screw

Part# 94144

Securing Luminaire Joints

p. 9, Step 6

Securing Corner Joints

p. 11, Step 8

Diffuser

Protective Bag

Backplate

Mud Guard

(provided)

ID Labels

Factory Order

Number

Job Name

Unique Luminaire

ID Number

Full Catalog

Order ID

Luminaire

Section Type

Luminaire Type

and/or Run Length

• Finelite has provided items

listed here, with their

Finelite part numbers.

These items can be found

in separate boxes shipped

with the luminaire.

• Account for all parts

and set aside until they

are needed.

• All other hardware needed

for this installation will be

"by others".

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 5 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

• Carefully rotate backplate out and let hang from luminaire body.

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

Step 3 - Opening Luminaires

Backplate

• Open all backplates for access to mounting points.

• Release the backplates from clips by sliding the blade of a putty knife behind backplate edges.

• To use a flathead screwdriver: From inside backplate, press end of screwdriver against the clip until the backplate is released.

Backplate

Flathead

Screwdriver

Clip

Backplate

Putty Knife Option

Flathead Screwdriver Option

Putty

Knife

Clip

Backplate

Clip

Release Backplates

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 6 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

Step 4 - Mounting Starter to Structure

• While properly supporting luminaire, maneuver luminaire near

wall/ceiling opening.

• Make electrical connections at ENDCAP, at TOP or with a

SPLICE BOX.

Jam Nut Jam Nut

Conduit Plate

#8 Screw

Conduit Plate

#8 Screws

Jam Nut

Conduit Plate

Starter

Conduit

CONTINUED

CONDUIT PLATE - ENDCAP

• Remove two screws holding conduit plate.

• Install conduit and jam nut onto conduit plate.

• Wire-nut electrical connections. See wiring legend above.

• Reinstall conduit plate and screws. Do not damage any wires.

CONDUIT PLATE - TOP (HP-4 ONLY)

• Remove screw holding conduit plate.

• Install conduit and nut onto conduit plate.

• Wire-nut electrical connections. See wiring legend above.

• Reinstall conduit plate and screw. Do not damage any wires.

SPLICE BOX (OPTIONAL)

• Lift tab to unsnap and remove splice box cover.

• Install conduit and nut onto splice box cover.

• Wire-nut electrical connections. See wiring legend above.

• Reinstall splice box cover. Do not damage any wires.

Wire-nut electrical

connections.

(Typical for all options.)

WIRING LEGEND

Black Hot Line Voltage

White Neutral Line Voltage

Green Ground

Grey Dimming 0-10V DC

Purple Dimming 0-10V DC

A. Make Electrical Connections

Flex Conduit

(by others)

Electrical Connection Options

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 7 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

Step 4 - Mounting Starter to Structure

Option 1 (Shown) - Mount to Threaded Rod

• Align threaded rods with mounting holes and slide luminaire into wall/ceiling.

• Install 1/4"-20 nut and 1/4"-20 washer onto 1/4"-20 threaded rod.

• CRITICAL: If installing a joiner luminaire in the next step, leave the nut loose,

allowing the luminaire to hang out of ceiling at an angle.

• If there is no joiner. PROCEED TO STEP 7.

Option 2 - Mount to Structure

• Slide luminaire into wall/ceiling and mount to structure support with hardware

appropriate for the structure type.

• CRITICAL: If installing a joiner luminaire in the next step, leave the bolt/screw

loose, allowing luminaire to hang out of ceiling at an angle.

• If there is no joiner. PROCEED TO STEP 7.

Ceiling

Starter

1/4"-20 Threaded Rod

(by others)

Drywall Ceiling Drywall Ceiling

Option 1 (Shown) - Mount to Threaded Rod

Option 2 - Mount to Structure

1/4"-20 Lag Bolt

(by others)

Support

Blocking

(by others)

Support

Blocking

(by others)

Support

Blocking

(by others)

Support

Blocking

(by others)

Structure Support (by others)

B. Mount Starter to Structure

1/4"-20 Washer

(by others)

1/4"-20 Nut

(by others)

Threaded Rod

(by others)

1/4"-20 Lag Bolt

(by others)

Mounting Option 2Mounting Option 1

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 8 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

Step 5 - Joining Luminaires

• Align joiner with aligner sleeves on starter and slide together. Be careful not to

damage any wiring.

• If necessary, lift both luminaires, then slide together.

B. Join Luminaires

Joiner

Starter

Aligner Sleeves

• While properly supporting luminaire, maneuver luminaire near wall/ceiling opening.

• If necessary, loosen bolts on previous luminaire so that it can hang out of the opening at an angle.

• After installing a joiner, return to previous luminaire and tighten.

A. Mount Joiner/Ender to Structure

Starter Joiner/Ender

Ceiling

Option 1 (Shown) - Mount to Threaded Rod Option 2 - Mount to Structure

• Align threaded rods with mounting holes and slide luminaire into wall/ceiling.

• Install 1/4"-20 nut and 1/4"-20 washer onto 1/4"-20 threaded rod.

• CRITICAL: If installing a joiner luminaire in the next step, leave the nut loose,

allowing the luminaire to hang out of ceiling at an angle.

• Slide luminaire into wall/ceiling and mount to structure support with

hardware appropriate for the structure type.

• CRITICAL: If installing a joiner luminaire in the next step, leave the

bolt/screw loose, allowing luminaire to hang out of ceiling at an angle.

CAUTION

DO NOT attempt to join luminaires

together on the floor. Damage

may result when lifted. Follow

these instructions.

1/4"-20 Washer

(by others)

1/4"-20 Nut

(by others)

Threaded Rod

(by others)

1/4"-20 Lag Bolt

(by others)

Mounting Option 2Mounting Option 1

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 9 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

B. Make Electrical ConnectionsA. Secure Joint with Yoke Brackets IN ALIGNMENT CORRECTLY INSTALLED

Joiner

Starter

Yoke Screws

(provided)

Aligner Sleeves

Yoke Brackets

(provided)

Step 6 - Securing Luminaire Joints

Yoke Bracket w/ Screw

#10-32 x 5/8" (provided)

• Connect plug-together wiring.

Luminaire Joint Luminaire Joint

YESNO

YOKE SCREW ALIGNMENT Bottom-Up View

Cross Section

View

Joiner

Starter

Plug-Together Wiring

Joiner

Aligner Sleeves

Joiner

Aligner Sleeves

Luminaire Joint

NOTE: Yoke screws should be installed directly across from each other, not diagonally, and in holes furthest from

the joint line. One yoke screw per one yoke bracket.

• Before installing yoke brackets, ensure the joining ends of luminaires meet flush and square.

• CRITICAL: Ensure yoke brackets properly engage with aligner sleeves.

• Secure joint by threading (but not yet tightening) yoke screws through yoke brackets and

into aligner sleeves.

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 10 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

A. Mount Ender to Stucture B. Join Mitered Luminaires C. Secure Ender to Structure

Step 7 - Joining Mitered Corners

Starter

1/4"-20 Lag Bolt

(by others)

1/4"-20 Nut

(by others)

1/4"-20 Washer

(by others)

Mounting Option 1 Mounting Option 2

Aligner Sleeves

Joiner

Ender

• Align ender with aligner sleeves on joiner and slide together. Be careful not to

damage any wiring.

• If necessary, lift both luminaires, then slide together.

• Secure ender to structure using preferred mounting option.

• CRITICAL: If installing a joiner luminaire in the next step, leave the nut or bolt/screw loose,

allowing the luminaire to hang out of ceiling at an angle.

• If there is no joiner, then tighten nuts or bolt/screws fully.

• Manuever ender near wall/ceiling opening.

• If necessary, loosen bolts on previous luminaire so that it can hang

out of the opening at an angle.

Joiner

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 11 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

B. Make Electrical Connections

Step 8 - Securing Corner Joints

Yoke Bracket w/ Screw

#10-32 x 5/8" (provided)

1Screwdriver with 6" bit required.

• Before installing yoke brackets, ensure the joining corners of luminaires meet flush

and square.

• CRITICAL: Ensure yoke brackets properly engage with aligner sleeves.

• Secure joint by using a screwdriver¹ to tighten yoke screws through yoke brackets and

into the aligner sleeves until joint seam of luminaire is closed.

Yoke Brackets

(provided)

Yoke Screws

(provided)

Aligner Sleeves

Ender

A. Secure Corner Joint with Yoke Brackets IN ALIGNMENT

CORRECTLY INSTALLED

Mitered Corner Joint

Plug-Together Wiring

• Connect plug-together wiring.

Ender

Joiner

A. Close All Backplates

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 12 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

Step 9 - Closing Luminaires

• Secure spackle flanges to wall/ceiling using appropriate screws or fasteners1for hard

surface, per local building codes.

• Install the "mud guards" cardboard inserts to help prevent spackle and paint from getting

into the luminaire.

• Spackle and paint over flanges up to luminaire edge.

• CAUTION: Careful not to drop spackle into luminaire. Immediately wipe off excess spackle

that may have gotten onto luminaire edges.

• Perform all spackling and painting to walls and ceiling prior to removing "mud guards."

• Remove all mud guards.

Every 6"to 12"

Mud Guard (provided)

Mud Guard

(provided)

Putty Knife

Spackle

Ceiling

Wall

A. Close All Backplates

• Reinstall all backplates by snapping into clips.

Backplate

Clip

B. Secure Flange To Structure Spackle Flange Only C. Apply Spackle Spackle Flange Only

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

1Screws or fasteners: drywall - drywall screws, wood - wood screws, etc.

Screws/Fasteners

(by others)

CONTINUED

Patent Pending

Note: All power connections to be installed to local/national codes by a Certified Electrician. Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • (510) 441-1100 • Fax: (510) 441-1510 • www.finelite.com 13 of 13

HP-2 / HP-4 / HP-6 Recessed or Regressed Spackle & Visible Flange Mitered Corner

Installation Instructions

D. Final Step - Replace Diffusers

• Remove diffusers from protective plastic bag.

• CAUTION: Wear gloves to keep diffuser surface clean.

• CRITICAL: Be sure to install correct diffuser to its corresponding luminaire ID.

• Install diffusers into luminaire body, ensuring they snap into place.

• Turn power on to luminaire.

ID: 1

ID: 2

ID: 3

Ceiling

This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary.

Step 9 - Closing Luminaires

Finelite HP-2 User manual

Popular Lighting Equipment manuals by other brands