INNOVAPLAS BILTMOR 5001 User manual

REV. 02/07/2023 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
WARNING
Install the step on a flat surface.
Do not jump or dive from the step.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
Maximum weight: 300 lbs / 135 kg.
Required tools (not included)
A
2X
GUSSET
INSERT NUT
1) Insert the two gussets in the slots and slide them
toward the corners.
2) Assemble the two main modules with the six screws,
nuts and washers provided.
3) Snap the door between the top and bottom module
within the slots provided.
Sand
(not included)
Sand
15 lbs
x6 x6 x6
A B C
Phillips #2 Phillips #3 7/16 wrench
Phillips bit
BILTMOR 5001 WITH DECK KIT 9005
Sand
15 lbs
Contents of the Biltmor box SKU # 5001
x12
(3/4 IN.)
x4
SCREW BAG 140-0001
(1 1/2 IN.)
F D
Contents of the deck kit SKU # 9005
x2
SCREW BAG 140-0020
x6 x6 x6
(1 IN.)
(³⁄4IN.)
x2
(³⁄4IN.)
x20
AB C D E
x4 x2
x2 x4
x2
x2

REV. 02/07/2023 PN: PG:2
2257 route 139
Drummondville, Québec
J2A 2G2
WWW.INNOVAPLAS.COM
BC
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
1) Snap the four post ends into the
step, making sure that the cylindrical
part is vertical and that the ends are
snapped properly in their respective
housings.
2) Snap the two feet to the bottom of
the step.
D
BILTMOR 5001 WITH DECK KIT 9005
’3
1/4
’
1/4”
align screws from
center of plate
x20
x2
1) Insert the four posts into the post
ends and secure them in place with the
screws provided.
2) Insert the two deck supports over the
rear posts.
3) Insert the handrails on the four posts
and secure in place.
4)
Fasten the access panel with the screws
provided.
D
x3
D
E
F
Sand
15 lbs
Sand
15 lbs
1) For installs where the deck support
is located more than 52" (132 cm)
from the bottom of the step, you can
add 2 15 lbs (7 kg) sand bags on
either side of the third step, as
shown.
2) Install the small post
covers.
1) Affix the deck supports
with the screws supplied.
F
x12
D
F
E
G
1) Slowly submerge the
step into the pool. Make
sure you do not damage
the pool liner in the
process.
2) Angle the whole step
so that it is entirely under
water. Purge all the air from
under the steps.
1) Pull the deck
supports (already fixed
to the deck) upwards to
create a spring effect
on the step.
2) Fasten the supports
to the two rear posts
while pushing the entire
step downwards.
x4
D