FingerTec AC100C User manual

AC100C TA100C TA200 Plus
Color Time Attendance System
User Guide

2
CONTENTS
5-7 Chapter 1 • GETTING STARTED
Viewing the User Guide in the Internet
Terminal Included Accessories
Included Printed Materials
Registering Terminal
8-12 Chapter 2 • BASICS
Introduction to Terminal
Terminal Overview
Main Menu
Power On/Off Button
Battery
Date/Time
Voice Control
Security Features
Cleaning Terminal
Restarting and Resetting Terminal
13-16 Chapter 3 • USER
Enrolling User
Verifying User
Adding User Information
Deleting User
Access Level/Privilege
Defining Work Codes
RFID Card Function
17-19 Chapter 4 •
INSTALLATIONS & CONNECTION
Installations
Communications
20-23 Chapter 5 • SYSTEM
System Settings
Data Management
Data Update Using USB Flash Disk
Keyboard
Display Settings
Reset
Misc Settings
24 Chapter 6 • DATE/TIME
Setting Date/Time
Daylight Saving Time
25 Chapter 7 • AUTO TEST
Who should do the Auto Test?
26 Chapter 8 • RECORD
Checking Records of Users in the
Terminal
27 Chapter 9 •
SYSTEM INFORMATION
Records
Device
28-29 TROUBLESHOOTING
“Unable to Connect” Appears
“Admin Affirm” Appears
Difficult to Read Finger
The LED is Blinking All The Time
“Duplicate Finger” Appears
RFID Card Doesn’t Respond
No Sound

3
AC100C MODEL
1• GETTING STARTED
Viewing the User Guide in the Internet
The User Guide is available in the package when you purchased the terminal. The User
Guide is also available online at http://www.timeteccloud.com/hardware. Choose the
language that you prefer for your User Guide.
Terminal Included Accessories
Do not abuse the fingerprint sensor by scratching the surface, contacting the sen-
sor’s surface with heat, pressing hard during placement of fingerprint for verifica-
tion. Clean the sensor occasionally with microfiber cloth to maintain the perform-
ance of the sensor.
USB Extension
To connect to the USB port of a com-
puter for uploading and downloading
of data.
A Packet of Bolts
Use the screws to hold the back plate
of the terminal against a wall.
DC 5V Power Adaptor
For supplying power to the terminal.
Screwdriver
Use the screwdriver to open the back plate
of ngerprint terminal and to install the back
plate against a wall.

4
TA100C MODEL
TA200 PLUS MODEL
A Packet of Bolts
Use the screws to hold
the back plate of the ter-
minal against a wall.
DC 12V Power Adaptor
Connect the power adapter to the
terminal and plug it into a standard
power outlet to charge the terminal.
RFID Cards (5 pieces)
For card enrollment and veri-
cation.
Screwdriver
Use the screwdriver to open
the back plate of ngerprint
terminal and to install the
back plate against a wall.
DC 5V Power Adaptor
For supplying power to
the terminal.
RFID Cards (5 pieces)
* Exclusively for TA103C-R
model only
For card enrollment and
verication.
USB Extension
To connect to the USB port
of a computer for upl
oading and downloading of
data.
Siren Cable
For connecting the terminal to
external siren.
Screwdriver
Use the screwdriver to open the
back plate of ngerprint termi-
nal and to install the back plate
against a wall.
A Packet of Bolts
Use the screws to hold the back
plate of the terminal against a
wall.

5
Included Printed Materials
• FingerTec Comprehensive DVD
• Quick Start Guide
• Pamphlet
• User Enrollment Template Form
• Warranty Card
Registering Terminal
Make sure that you register your terminal’s warranty with us at
http://www.fingertec.com/ver2/english/e_warranty.htm
for a 36 month warranty protection.

6
AC100C MODEL
L.E.D Display LCD Screen
Keypad Fingerprint
Sensor
Speaker
Reset
s u p p o r t @ f i n g e r t e c . c o m
Reset Button & USB Port
2 • BASICS
Introduction to Terminal
FingerTec is a renowned brand name for commercial products for door access and time
attendance systems. FingerTec offers a wide range of products to cater to the growing
needs for biometrics products in office/home automation as well as in security indus-
try.
FingerTec terminals are loaded with powerful microprocessor that can process biomet-
rics authentication methods for accurate personal identifications and for collection of
precise data for time attendance. In addition, some fingerprint terminals are made to
accept card verification as an added security measure.
This manual covers colored time attendance models of FingerTec products, which includes
AC100C, TA100C and TA200 Plus. The terminal acts as a tool to collect attendance data. For
a processing of attendance data, FingerTec is providing a powerful time management soft-
ware, to process data and provide accurate and reliable attendance reports.
Terminal Overview
ITEM FUNCTION
LCD Screen Displaying status of terminal, day, date, time and the icons available.
LED Display Green LED – The terminal is working fine and it is in standby mode.
Red LED – There is an error at the terminal that requires checking. For first
time use, the terminals need to be charged fully to avoid having the red
light blinking.

7
TA100C MODEL
L.E.D Display
LCD Screen
Keypad Fingerprint
Sensor
RFID Card
Induction Area
Speaker
s u p p o r t @ f i n g e r t e c . c o m
Reset
Reset Button & USB Port
ITEM FUNCTION
Keypad To input instructions into the terminal and to allow configuration.
Fingerprint Sensor To scan finger for confirmation of identity.
Speaker For terminal voice emission.
USB Port To upload/download users information, password and transaction
logs via USB disk.
Reset Button To restart the terminal as and when required.
ITEM FUNCTION
LCD Screen Displaying status of terminal, day, date and time.
LED Display Green LED – The terminal is working fine and it is in standby mode.
Red LED – There is an error at the terminal that requires checking. For
first time use, the terminals need to be charged fully to avoid having the
red light blinking.
Keypad To input instructions into the terminal and to allow configuration.
Fingerprint Sensor To scan finger for confirmation of identity.
RFID Card Induction Area Area that reads RFID cards. * for TA103C-R only
Speaker For terminal voice emission.
USB Port To upload/download users information, password and transaction
logs via USB disk.
Reset Button To restart the terminal as and when required.

8
L.E.D Display
LCD
Screen
Keypad
TA200 PLUS MODEL
RFID Card Induction Area
Speaker
Fingerprint
Sensor
Navigation
Keys
Reset Button
USB Port
ITEM FUNCTION
LCD Screen Displaying status of terminal, day, date and time.
LED Display Green LED – The terminal is working fine and it is in standby mode.
Red LED – There is an error at the terminal that requires checking. For first
time use, the terminals need to be charged fully to avoid having the red
light blinking.
Keypad To input instructions into the terminal and to allow configuration.
Navigation Keys To navigatien and input command to terminal.
RFID Card Induction Area Area that reads RFID cards.
Speaker For terminal voice emission.
Reset Button To restart the terminal as and when required.
Main Menu
Enroll users, manage user data and input workcode.
Setup FingerTec terminal communication with computer through LAN, RS232 and
RS485. Set security password of the device for a secure data transfer.
Configure the settings of the FingerTec terminals from general to display setting to
fingerprint. Data management, update via USB flash disk, keyboard functions, reset and
other terminal settings can be done here.
Adjust the date and time settings of the terminal.

9
Upload and download data and information to and from the FingerTec terminal
using a USB flash disk.
Run tests on the FingerTec terminal to diagnose the terminal on various aspects.
Check user attendance and transaction logs that are available in FingerTec termi-
nals and perform housekeeping of the machine.
View free and used memory of the terminal as well as the terminal’s details in sys-
tem information.
Power On/O Button
Use the power on/off button to turn the terminal on or off. You can disable the but-
ton to avoid accidental shut off of the terminal.
Battery
FingerTec terminals operate using power supply from a standard power outlet. In-
side each terminal, there is an RTC battery to keep the clock of the terminal running.
When there is a serious delay in time or the clock of the terminal reverts to 00:00 after
restarting, this indicates that the RTC needs to be replaced.
External power supply: Mini UPS (uninterrupted power supply) 5V and mini UPS 12V
provides mobile power supply to the terminals. Charge the mini UPS sufficiently for
optimum performance.
Refer to http://accessory.fingertec.com for more information about accessories.
Date/Time
The terminals display the date and time at the home screen. Choose the date and
time format based on your preference. Press Menu > Date/Time > Select Value > OK
to save.
Voice Control
Voice Control lets you control the level of volume emitted by the terminal.
TURN ON/OFF
The system lets you to turn on/off the voice based on your preference. Press Menu >
System > System > Voice > On/Off > Determine value in percentage (default is 67%)
> OK to save.

10
ADJUST VOLUME
The default volume of the terminal’s voice is 67. The volume can go as high as 100 and
as low as 0. To sustain the performance of speaker, it’s recommended to stay within
the range of 60-70. To adjust the volume Press Menu > System Icon > System > Vol >
input value > OK to save
Security Features
Security features help protect the information in the terminal from being accessed by
unauthorized individuals.
ADMIN AFFIRM
Register an administrator to the system by enrolling a fingerprint or a password to a
user ID. Press Menu > User Mgmt > New User > Privilege: Admin > Choose enrollment
method > OK to Save. After enrolling an administrator, the main menu can only be
accessed by the administrator. The terminal will display “Admin Affirm” when an anau-
thorized individual tries to access the Menu.
COM KEY
Create password for a specific terminal here. Press Menu > Comm. Icon > Security >
Insert Terminal ID No and Password > Ok to save. The security password known as
COM Key is intended for extra security. To connect the terminal with the software, the
COM key inserted in the Software must be the same as the one inserted in the termi-
nal or else the connection will not be established even though the activation key and
product key are correctly inserted.
Cleaning Terminal
CLEANING THE BODY
Use a dry cloth to clean the terminal’s body. Do not use any liquids, household clean-
ers, aerosol spray, solvents, alcohol, ammonia and abrasive solutions to clean the body
of the terminal because it could damage it.
CLEANING THE FINGERPRINT PRISM
Clean the fingerprint prism with a cellophane tape for silicon coated prism.
View the video on how to clean the fingerprint prism at this link
http://www.fingertec.com/newsletter/enduser/cleanfinger.html.
For the non-coated prism, please use microfiber cloth.
Restarting and Resetting Terminal
If a feature isn’t functioning as it should, try restarting or resetting the terminals
RESTARTING THE TERMINAL
Push the On/Off button on the terminal to restart the terminal. If you can’t restart the
terminal, or if the problem persists, you might want to reset.
RESETTING THE TERMINAL
Go to Menu, press the System icon and click on Reset. Choose to Reset All Default Set-
tings, Reset Keyboard Settings or Reset Other Parameters. Resetting the terminal will
cause all your settings to return to the original factory settings.

11
3 • USER
Enrolling User
The FingerTec terminals can enroll fingerprint templates, passwords and card informa-
tion. This chapter covers all possible user enrollments in the terminals.
FINGERPRINT ENROLLMENT
It is recommended to enroll two fingerprints for one user ID. One template is the default
fingerprint and another is used as for backup. You need to check the quality of the finger-
print before doing any fingerprint enrollment. It is important to locate the center points
of the finger because the center points has to be placed in the middle of the scanner
during enrollment to get a good reading. You also have to make sure that the fingers are
not too wet or too dry for enrollment.
To enroll ngerprint: Press Menu > User Mgmt icon > New User > ID. No: (insert value) >
Select “Enroll FP” > Select Privilege > Place your fingerprint 3 times following instructions
given by the terminal > OK to save.
CARD ENROLLMENT
For terminals that are using card system, the default card technology for the terminal
is RFID. MiFare and HID card modules are available upon request.
To enroll card: Press Menu > User Mgmt icon > New User > ID No: > Insert User ID >
Select “Enroll Card” > Wave the card at the scanning area until the screen displays the
Card ID > OK to save.
PASSWORD ENROLLMENT
The terminal offers different enrolment methods, and passwords can be used alone or
in combination with other verification methods. The maximum length of a password
is 8 digits.
To enroll password: Press Menu > User Mgmt icon > New User > ID No: (insert value)
> Select “Enroll Pwd” > Input password using the keypad > Reconfirm password > OK
> OK to save.
Verifying User
1:1 ONE TO ONE / 1:N ONE TO MANY
VERIFICATION METHOD PROCESS
1:1 (One to One) You have to identify your User ID before inputting any biometrics
feature for verification. For example, your user ID is 1008. One to
one method requires you to key in user ID followed by your finger-
print to get verified.
1:N (One to Many) You don’t need to identify your User ID before inputting any bio-
metrics feature for verification. Simply place your finger on the
scanner for verification.

12
Center points
VOICE MESSAGE
VOICE / MESSAGE WHAT DOES IT MEAN?
“Verified” Identity verification is successful, the terminal stores the transaction
logs and opens the door (if connected to door access)
“Try again please” Identity verification is failed because the finger is not properly posi-
tioned, the template is not available in the terminal or the password
is incorrect.
“Admin Affirm” You are not an administrator of the system and you cannot access
Menu page
“Duplicate Finger” This message only appears during registration when the finger that
you want to enroll has been enrolled before. “FP Enrolled Alrd” will be
displayed on the LCD screen.
“Invalid ID” For 1:1 verification, User ID entered does not match with fingerprint.
FINGERPRINT VERIFICATION
1:N – 1:N verification does not require any input of your user ID. Place your finger properly on
the scanner and the terminal will take a second to verify your identity.
1:1 – 1:1 requires input of User ID before the terminal reads and verifies your identity. Press
1:1/1:N > Input ID on the screen > Press fingerprint icon > terminal will read and verify.
Some precautions have to be taken to get a good read every time.
·Make sure the center point of your finger is
placed in the middle of the scanner for a good read.
·Recommended to use index finger. The terminal
accepts other fingers but index is the most convenient.
·Make sure the finger is not wet, too dry, injured or dirty
·Do not press hard on the sensor, just place it
comfortably
·Avoid direct sunlight or bright light
PASSWORD VERIFICATION
Password can be an option for those who do not prefer to use other verification methods. To
verify using password, press 1:1/1:N > insert User ID and press key button > insert password
and press OK.
CARD VERIFICATION
Place the card on the card scanning area and the terminal will read and verify the card.

13
Adding User Information
User information can be added into the terminal through two ways. One is through
the Fingertec terminal and the other through TimeTec Cloud. To add/change user in-
formation via the terminal, press Menu > User Mgmt icon > Manage User > OK > Select
Instruction > Edit/Add > OK to Save.
Instruction Function
Search User Insert User ID in the column and press OK
Record Press to view available user records
Edit User Delete/Add Verification Methods and change Privilege
Del User Delete User, Fingerprint or Password
New User Enrolment of New User
Field Function
ID No. Edit user ID based on your company’s employee numbering system. Maximum length
of user ID is 9 digit
Name Add name of the user in this field (Can be done via TimeTec Cloud). Maximum number
of characters is 24
FP Quantity of Fingerprint
PWD Quantity of Password
CARD Quantity of Card
It is recommended that the updating of user information be done through the TimeTec
Cloud software. After the information is updated, sync the software and the terminal
to display the information.
Deleting User
Only an administrator can perform user deletion at the FingerTec terminal. To delete
certain user(s), press Menu > User Mgmt > Manage User > OK > Select Del User >
Choose “Delete User” > OK
Please be extra careful when performing this task to avoid any unauthorized deletion.

14
REASONS WORK CODE
Check In 00
Check Out 01
OT start 04
Done 05
Sick Leave 10
Half-day Leave 12
Emergency Leave 11
Meeting Client 20
Outstation 21
Workcode Mode 1: Verification followed by work code
Workcode Mode 2: Work code followed by verification
Access Level/Privilege
FingerTec terminals offer two types of access level or privilege.
PRIVILEGE USER ROLES
Normal User Only use the terminal to verify your identity. You cannot access into
Menu and make changes into settings and system
Administrator You are allowed to access into menu to enroll users and edit settings
and system
Dening Work Codes
The terminal provides a work code fea-
ture which allows users to key in pre-
defined numbers after verification. The
work code numbers are predefined in
the TCMS V2. The following table shows
examples of work codes.
Press Menu > User Mgmt > WorkCode
> Press ok to activate the menu > Select
to Create New workcode, Edit Work-
code or to Delete Workcode > Choose
your preference > Ok to save.
To add work code through the terminal,
Press Menu > User Mgmt > Workcode >
Menu > New > Enter Code Number eg:
02 > Enter Code Name eg: Emergency
Leave > OK to save.
RFID Card Function
The fingerprint terminals are versatile and some can accept card verifications. This
chapter covers the Radio Frequency Identification or better known as RFID system. The
terminals accept RFID card with specifications of 64-bit, 125kHz.
ENROLLMENT OF RFID CARD
RFID can be enrolled alone, with fingerprint or with password. Each RFID card comes
with a unique ID and the terminals will read from the numbers and match it with the
card.
Enrollment of RFID is easy. Press Menu > User Mgmt > New User > Enroll Card > ware
card at the induction area > OK.
CHANGING CARD ID
Press Menu > User Mgmt > Manage User > OK > Change Card > OK > Show a different
card > OK.

15
4 feet / 1.2 meter
(recommended)
4 • INSTALLATIONS & COMMUNICATION
Installation
FingerTec terminals offer several connections for power and communications. Installations
of FingerTec time attendance terminals are simple.
MOUNT ON WALL
• After measuring the height accordingly
and make relevant marking on the wall,
drill the screws into the wall to secure
the back plate.
• Attach the terminal to the back plate
and tighten the screws.
FLEXIKIT
FingerTec offers flexi-kit for all its time attendance models. Attach the terminal on the flexi-
kit for convenience and cosmetic purposes. View flexi-kit at http://accessory.fingertec.com

16
AC100C MODEL & TA100C MODEL
TA200 PLUS MODEL
Reset
Reset
TCP/IP PORT
POWER PORT
USB PORT
........
......
TCP/IP PORT
POWER PORT
USB PORT
........
......
Communication
Connection points for power and communication are available on top of the terminals.
Refer to the following diagrams for the terminals you require.

17
1 8
TOP
FRONT
1 8
CONNECTOR PIN CABLE COLOR CONNECTOR
TX+ 1•White/Orange •1 TX+
TX- 2•Orange •2 TX-
RX+ 3•White/Green •3 RX+
4•Blue •4
5•White/Blue •5
RX- 6•Green •6 RX-
7•White/Brown •7
8•Brown •8
JOINT 1 PIN JOINT 2 PIN
TX+ 1 • • 3 RX+
TX- 2 • • 6 RX-
RX+ 3 • • 1 TX+
RX- 6 • • 2 TX-
USB PORT
Linking with USB flash disk for remote data transfer.
TCP/IP PORT
Connect with CAT 5 cable for LAN connection, one end to this port
and another end to the computer’s TCP/IP Port.
TCP/IP for Single Connection – Linking the
terminal to a single computer using TCP/IP requires
Ethernet 10/100Base-T Crossover Cable. The cable
can be used to cascade hubs or to connect Ethernet
stations back-to-back without a hub. It works with
both 10Base-T and 100Base-TX.
TCP/IP for Network Connection – Linking the terminals to multiple computers using TCP/IP
requires Ethernet 10/100Base-T Straight Thru Cable or “whips”. The cable works with both 10Base-T
and 100Base-TX, connecting a network interface card to a hub or network outlet.
POWER SUPPLY PORT
Insert the Power Adapter point to this port for power.
LOGIN TO TIMETEC CLOUD TO START
To insert TimeTec Cloud server IP > Press Menu > COMM > Web Setup > Webserver
IP (50.18.154.243) > Webserver Port (80) > OK (Save) > ESC to return to main screen >
Restart to apply changes
Login to TimeTec Cloud to start to setup your company
• Visit to www.timeteccloud.com
• Login by using your username (email address) and password
• Go to Configuration > Wizard > Setup Wizard
• Follow the instructions under Setup Wizard

18
5 • SYSTEM
System Settings
THRESHOLD
Threshold is the level of the fingerprint scanner’s sensitivity. Threshold determines how
many percent of minutiae points on a fingerprint template will be read by the system.
The higher the threshold level, more points are being read, more restricted the system.
Configure the threshold for 1:1 and 1:N methods.
For 1:1, the range is from 0-50 and the recommended value is 15.
For 1:N, the range is from 0-50 and the recommended value is 35.
Press Menu > System > System > Threshold (1:1) or Threshold (1:N) > Determine the
Level > OK to Save
DATE FORMAT
The date format can differ based on countries for example in Malaysia, the date-month-
year format is used while in America, the month comes first. Choose your date format
according to your preference. The default format is dd-mm-yy. Press Menu > System >
Date Format > Select Format > Ok to Save
SOUND OF KEYBOARD
The terminal emits sound when you press any of its buttons.
To turn on/o the keypad sound: Press Menu > System > Keybeep > On/Off >Ok to Save
FINGER SENSITIVITY
Determine the sensitivity of the sensor to fingerprint. Choose Low, Mid or High sensi-
tivity. It is recommended to be set at Mid. Press Menu > System > Finger Sensitivity >
Select your preference >Ok to Save
VOICE
The terminal has certain voice commands to guide users during enrolment and to no-
tify users during verification. Press Menu > System > Voice > On/Off > OK to save
VOLUME %
Voice Control lets you control the level of volume emitted by the terminal.
Adjust Volume: The default volume of the terminal is 60. The volume can go as high as
100 and as low as 0. To sustain the performance of speaker in the terminal, it’s recom-
mended to stay at the range of 60-70. To adjust the volume. Press Menu > System >
Volume 1:100% > Set your number > Ok to Save.
ALGORITHM VERSION
Get the terminal’s algorithm version here. Press Menu > System icon > System > Alg
Version > View the Version > Ok to Save.

19
DESCRIPTION CODE
Terminal ID 01
Date (ddmmyy) 050210
Time (hhmm) 0900
User ID 000000001
Transaction Code 00
Terminal Activity 00
NOTE
Please be extra careful when
performing this task to avoid
unauthorized deletion of
important data
RECHECK MIN
Once you have inserted a value, eg: 1, when a user checks in at 10:01, his time will be
adjusted to 10:00. The maximum value is 99. When you enter 5, a user is given 5 minutes
leeway time in his attendance.
LOG ALERT
When the log storage is at a certain level, the user/administrator needs to be alerted to
avoid underperformance of terminal. The recommended value is 99. Menu > System >
System Settings> Log Alert > Input your value > Save
Data Management
Every time an enrolment is performed or a
verification is done, a transaction log is stored
inside the terminal. The data contains the ter-
minal ID, date, time, user ID and transaction
activity. For example, 0105021009000000000
010000:
These logs need to be managed to maintain
the effectiveness of the terminal.
There are 4 functions available in the Data icon to enable you to manage your data in
the FingerTec terminal.
In the data management icon, you can choose from four instructions. Press Menu >
System > Data Mgmt > Select your instruction > Ok to save
DELETING ATTLOG
Please make sure that you are certain when you want to do this operation. Make sure
that you have downloaded the logs into TimeTec Cloud before deleting it. Deleting the
logs means that no backup data is available.
DELETING ALL DATA
This function allows you to delete all attendance data and user information in the ter-
minal. Make sure that all user information has been backed up in TimeTec Cloud before
performing this task.
CLEARING ADMIN
There are three user privileges in the terminals, administrator, supervisor and normal
user. You can delete administrator privilege; but without an administrator, normal user
can access the menu easily and interrupt the settings.
DELETING PICTURE
You can advertise your product and company cor-
porate message in the terminal using screen saver
function.

20
Data Update Using USB Flash Disk
To update the terminal using a USB flash disk, press Menu > System > Update > Make
sure that you have the USB Flash Disk plugged into the terminal before you proceed.
Keyboard
Define the function keys in your terminal here. Press Menu > System> Keyboard > Se-
lect the function > Determine the Key Number > Name The function (To activate the
alphanumeric keyboard, press the right arrow button) > You can also set to auto switch
this function on a certain time of days > Ok to Save
Display Settings
NUMBER OF TRIES
1:1 Match Retry Times: You can set the limit to the number of tries for the 1:1 verifi-
cation mode. The range is from 1-9. If a user’s number of tries exceeds the limit, the
terminal could trigger the alarm system to alert security that somebody is meddling
with the terminal. Press Menu > System > Display> 1:1 Match Retry Times > Determine
the Value > ok to Save
Password Retry Times: You can set the limit to the number of tries for password veri-
fication. The range is from 1-9. If a user’s number of try exceeds the limit, the terminal
could trigger the alarm system to alert security that somebody is meddling with the
terminal. Menu > System > Display> 1:1 Match Retry Times > Determine the Value >
Ok to Save
Clock Mode: There are two clock modes available in FingerTec terminals. Choose the
one your prefer. Press Menu > System > Display> Clock Mode > Choose 1 or 2 > Ok to
Save
PICTURE DELAY
Picture delay refers to the idle period before the screen displays your loaded advertise-
ment. It ranges from 0-999 seconds. Press Menu > System > Display > Picture Delay >
Determine your time > Ok to Save
CLOCK DELAY
Clock delay is an idle period before the screen displays your chosen clock picture. It
ranges from 0-999 seconds. Menu > System > Display > Clock Delay > Determine your
time > Ok to Save
Reset
Reset allows you to perform 3 tasks:
1. Reset All Default Settings
2. Reset Keyboard Settings
3. Reset Other Parameters
Please make sure that you are certain of performing any of the tasks before proceeding
to avoid loss of crucial data.