FingerTec AC800 Series User manual

Service Manual
AC800 Series Fingerprint Reader
JULY 2005 VERSION 1
Overview
Copyright © 2005 FingerTec Worldwide. All rights reserved.
SM800-01
Chapter 1
General Descriptions for AC800 Series
Fingerprint Reader
Chapter 2
Components - Details and Functions
2.0 Components Assembly
2.1 Details of Parts
2.1.1 Graphical Dot Matrix LCD
2.1.2 Connections between
Graphical Dot Matrix LCD
and Controller Board
2.1.3 Optical Fingerprint Sensor
2.1.4 Connections between Optical
Sensor and FP Matching Board
2.1.5 FP Matching Board
2.1.6 Connection of FP Matching
Board and AC800 Series
Controller Board
2.1.7 Keypad Board
2.1.8 Connection of Keypad Board
and Controller Board
2.1.9 Speaker
2.1.10 AC800 series Controller Board
2.2 Arrangements of Components in
AC800 Series Reader
Chapter 3
Troubleshooting and Repairing
3.1 Connection between Reader and PC
using LAN connection
3.1.1 Solutions
3.2 Connections between Reader and PC
using RS232/485
3.2.1 Solutions
3.3 Troubleshooting for LCD Screen
Displaying
3.3.1 Solutions
3.4 Troubleshooting for Fingerprint Sensor
3.4.1 Solutions
Chapter 4
Door Lock System
4.1 EM-Lock
4.2 Push Release Button
4.3 Override Key Switch
4.4 Emergency Break Glass
4.5 Complete connection of door lock
system
4.5.1 Simple door lock system (with
1 fingerprint reader)
4.5.2 Door lock system with in/out
reader
Compiled by K.L. Pang
Table of Contents
Model :AC801 / AC802 / AC803 /
AC801WG
Template Size :1k (AC801) / 1.5k (AC802) / 2.8k
(AC803)
Transaction Storage :30k (AC801) / 100k (AC802) /
120k (AC803)
Communication :RS232, RS485, TCP/IP; Wiegand
Identification Time :<=2s
FAR :<=0.0001%
FRR :<=1%
Time Zone :50 settings
Temperature :0 - 45°C
Power :12VDC @ 1A
Size :150(W) x 145(H) x 38.5(D) mm
One to many identification
One to one verification
10 fingers enrollment per user
Standalone and/or networked operation
50 definable time zones
Integrated wall mount design
Power management
In-Out reader configuration
Voice greetings
Wireless doorbell
Separate control of EM-Lock
26-bit Wiegand output (for WG model only)
•
•
•
•
•
•
•
•
•
•
•
•
Chapter 1: General Descriptions of
AC800 Series Fingerprint Reader

AC800 Series Fingerprint Reader Service Manual
Copyright © 2005 FingerTec Worldwide. All rights reserved.
Chapter 2: Components – Details and Functions
2.0 Components Assembly
Figure 2.1 Front view of AC800
Figure 2.2 Components inside reader
2

AC800 Series Fingerprint Reader Service Manual
Copyright © 2005 FingerTec Worldwide. All rights reserved.
Chapter 2: Components – Details and Functions
2.1 Details of Parts
2.1.1 LCD Display Board
LCD display board for AC800 series is connected to keypad board during factory assembly. LCD functions
to display text messages to user. It will prompt the user for necessary actions. For AC800 series reader,
the dimension of the LCD screen is 128x64 pixels (2.7cm X 4.2cm).
LCD screen
Figure 2.3 Front view of LCD
Display board
Figure 2.4 Back view of LCD
Displaying board
Keypad board
Connector pins
Contrast controller
Connector Pins
A cable to controller board connects this part. Improper connection could cause no LCD display
when reader is turned on.
•
Figure 2.4 IDE cable Figure 2.5 Connections between controller
board & keypad board
3
Keypad board Controller board
This IDE cable is used to connect keypad to the controller board.
This IDE cable is plugged into the connector pins on the keypad
board and controller board.
Please use the diagram below during plugging in of the IDE cable.