Fisher & Paykel DishDrawer DD60S Series User manual

DishDrawer®
Installation instructions
Important!
SAVE THESE INSTRUCTIONS
The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
DD60S models NZ AU GB IE
SAFETY AND WARNINGS
1
WARNING!
Electrical shock hazard
Before installing the DishDrawer®, remove the house fuse or open the circuit
breaker.
This appliance must be earthed. In the event of a malfunction or breakdown,
earthing will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having an
equipment-earthing conductor and an earthing plug. The plug must be plugged
into an appropriate outlet that is installed and earthed in accordance with all
local codes and ordinances. WARNING- Improper connection of the equipment-
earthing conductor can result in a risk of electric shock. Check with a qualified
electrician or service representative if you are in doubt as to whether the
appliance is properly earthed.
Do not modify the power supply plug provided with the appliance - if it will not
fit the outlet, have a proper outlet installed by a qualified electrician. Do not use
an extension cord, adapter plug or multiple outlet box.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
Important safety instructions!
Installation of this DishDrawer® requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the DishDrawer® installation, the Installer must perform the Final Checklist.
Remove all packaging materials supplied with the DishDrawer®.
This DishDrawer® is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The DishDrawer® MUST be installed to allow for future removal from the enclosure if service is required.
The switched power outlet must be outside the DishDrawer® cavity, so that it is accessible after
installation.
Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to
the power supply cord.
If the DishDrawer® is to be relocated from one installation to another it must be kept upright to avoid
damage from water spillage.
Make sure only new hoses are used for connection (supplied with DishDrawer®). Old hoses should not
be reused.
Failure to install the DishDrawer® correctly could invalidate any warranty or liability claims.
If the product is installed in a motor vehicle, boat or similar mobile facility, you must bring the vehicle,
boat or mobile facility containing the product to the service shop at your expense or pay the service
technician’s travel to the location of the product.
(1,1) -1- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:09 AM
(1,1) -1- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:09 AM

23
PRODUCT DIMENSIONS CABINETRY DIMENSIONS
A
B
C
E
D
F
G
H
J
K
Product dimensions ( (mm)
Prenished
LCD
DD60S
Prenished
Flat door
DD60S
Integrated
DD60S
Aoverall height* of product 409 409 409
Boverall width of product 599 599 599
Coverall depth of product (excl. curvature/handle) 570 570 570**
Ddepth of drawer (open) (excl. curvature/handle) 538 538 538
Eheight* of chassis 409 409 409
Fdepth of chassis (incl. trimseal) 552 552 552
Gdepth of drawer front panel (excl. curvature/handle) 18 18 18
Hdepth of curvature or handle 11 41 n/a
Iheight of drawer front 394 398 398 min
Jheight of venting area at base of product 79 9
Kheight of installation bracket slots (on top of chassis) 22 2
*Chassis heights include bracket slots ** Panel thickness - 18 mm
Note: for Prenished Flat door models, the height from the top of handle to the top of door - 64 mm
I
Installation diagrams for illustration purposes only
A
B
C
Cabinetry dimensions (mm)
Prenished
LCD
DD60S
Prenished
Flat door
DD60S
Integrated
DD60S
Ainside height of cavity 412 412 412
Binside width of cavity 600 600 600
Cinside depth of cavity 580 580 580
K
F
C
H
Installation diagrams for illustration purposes only
2.5 mm
2.5 mm
13 mm
Minimum clearances (mm)
(1,2) -1- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:09 AM
(1,2) -1- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:09 AM

PARTS SUPPLIED
Clamp (1)
Wire clip (1) Phillips
16 mm
screws (7)
Top mounting
brackets (2)
OPTIONAL
Drain hose
support (1) Moisture protection tape (1)
(to prevent moisture
damage)
Drain hose
joiner (1) Rubber washer for
inlet hose (1)
4
5CAVITY PREPARATION
If the Drain hose supplied is not long enough to reach your services, you must use a Drain Hose Extension Kit P/N 525798 which will extend the drain hose by 3.6m. The kit is available from the nearest Fisher & Paykel
Authorised Service Centre or our local website listed at the end of this document.
These marks indicate formed bracket screw locations.
Preferred position. If adequate clearance, services hole can be higher.
If hole is higher, ensure drain hose is routed straight into the waste connection.
Water Connection
Recommended COLD (Maximum 60°C).
¾“ BSP (GB20) to suit flat washer.
Water Pressure Max Min
Water softener models 1 MPa (145 psi) 0.1 MPa (14.5 psi)
Other models 1 MPa (145 psi) 0.03 MPa (4.3 psi)
Drains will need to be separated to satisfy kosher requirements.
We suggest you confirm acceptability with your local rabbi in
respect to kosher installations.
*
Note: Services can be located
either side of DishDrawer®.
Important!
Adjacent cabinetry must not
extend above cavity base
220-240 VAC
min. 4.5 A
min. 200 mm
10 mm
max.
450 mm
min. ø 60 mm
Moisture
protection
tape must
be applied.
**
Water supply
(2,1) -1- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:09 AM
(2,1) -1- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:09 AM

Max. distance of
hoses and cord from
chassis edge
Left hand
side
Right hand
side
Drain hose 2000 mm 1800 mm
Inlet hose 1650 mm 1250 mm
Power cord (excl. plug) 1650 mm 1650 mm
Left hand
side
Right hand
side
(2,2) -1- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:09 AM
(2,2) -1- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:09 AM

ROUTE THE HOSES AND MOVE INTO THE CAVITY
6
7REMOVE THE DRAWER AND SECURE THE PRODUCT
1
2
Tie together to avoid kinking.
A
The product has three pairs of
mounting brackets: a pair of
optional brackets on the top (C)
and two pairs of formed brackets
in the side of the chassis (A,B). Use
at least two out of the three pairs
to secure the product.
Ensure the sound insulation is
repositioned correctly.
B
2
30 mm
1
5
5
3
4
Ensure the drawer is removed and
then rotated anti-clockwise to
prevent kinked hoses
A
1
2
1
3
3
optional
(x2)
Ensure hoses and cord
are not kinked or twisted.
If top mounting brackets are
being used, ensure they’re
securely fitted before sliding
product into cavity
B
A
OR
optional
AA
B
B
CC
max. 19 mm
(1,1) -2- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:30 AM
(1,1) -2- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:30 AM

8REFIT THE DRAWER
2
1
4
5
4
3
Before refitting the drawer ,
ensure the hoses are not
twisted and the latches at
the rear of each drawer
runner are facing forward.
Ensure the drawer clips on
both sides are reset.
Ensure the drawer
is now rotated
clockwise back.
A
(1,2) -2- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:30 AM
(1,2) -2- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:30 AM

PLUMBING AND DRAINAGE OPTIONS
9
1
1
2
3
2
750-
882.5
mm
38 mm
max.
120
mm
750-
882.5
mm
7
6
4
3
4
5
6
180o
5
A
If space is limited for fixing, push
hose through drain hose support
to required height
DishDrawer® using sink trap
with drain hose joiner
750 - 882.5 mm
min. R 200 mm
180O
Supplied drain hose joiner
19 mm waste tee
HIGHLOOP
min. 150 mm
Ensure hoses are routed
straight to joiner.
Remove excess hose
material if necessary.
DishDrawer® and Standpipe Ø 38 mm
Fit the supplied
rubber washer.
Fit the supplied
rubber washer.
B
Waste Disposal
(optional)
Do not connect to
DishDrawer®
Waste Disposal (optional)
Do not connect to
DishDrawer®
750 - 882.5 mm
min.
R 200 mm
(2,1) -2- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:30 AM
(2,1) -2- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:30 AM

11
10 FINAL CHECKLIST TROUBLESHOOTING
Check all parts are installed.
Ensure product is level, securely fastened to the cabinetry and opens and closes
freely. The DishDrawer® must be free to fully close with no resistance from the
cabinetry.
Ensure inlet hose to water supply has supplied rubber washer fitted, and that
it’s tightened a further half turn after seal contact.
Ensure any knockouts or plugs in drain connection have been drilled out and
drain connection has been made.
The drain hose joiner must not support the weight of excess hoses. Keep hoses
as fully extended as possible to prevent sagging. Any excess length of hose
should be kept on the DishDrawer® side of the highloop.
If using Plumbing and Drainage OPTION B, ensure the Highloop is a minimum
150 mm higher than the drain hose joiner.
Turn on the power and water supply. Then press the Power ( )button to turn
the DishDrawer® on. The DishDrawer® should beep and Wash Programme lights
light up.
Check the spray arm is in place and free to rotate.
Add three cups of water into the DishDrawer®. On the Wash Programme
Selector Panel press Rinse and close the drawer. Start the programme by
pressing the Start/Pause ( )button.
After the Rinse programme has finished, ensure machine has run and drained
correctly.
Check water supply and drainage connection for leakage.
Spray arm
Excessive water remaining above the filter plate, after the rinse cycle
Check for kinked drain hoses or blocked waste connection, highloop not
properly installed or drain hoses not routed correctly.
No water supply (shows on display-models with LCD only)
Check water is connected, turned on and the spray arm is correctly fitted and
free to rotate.
No lights come on when the drawer is opened
Ensure power is connected and is switched on. Check if Auto Power option is
on.
Water around water supply and drainage connections
Check connections, existing plumbing and hoses for leaks. Check rubber
washer and hose clamp are correctly fitted.
If product is tipping
Ensure the product is secured to the cabinetry.
If front panels are misaligned
Check and relevel product. Check the cabinetry is square.
Drawer doesn’t close properly
Ensure nothing is obstructing the drawer from closing properly eg sound
insulation, hoses or drawer latches.
If a problem occurs, consult the Troubleshooting section of the User guide.
If after checking these points you still need assistance, please refer to the
Service & Warranty book for warranty details and your nearest Authorised
Service Centre, or contact us through our website, listed below.
www.sherpaykel.co.nz www.sherpaykel.com.au www.sherpaykel.co.uk www.sherpaykel.ie 599683B NZ AU GB IE 06.09
(2,2) -2- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:30 AM
(2,2) -2- 599683B DD60S installA2 NZGB.indd 6/7/09 11:36:30 AM