Fisher & Paykel ActiveSmart E522B Mounting instructions

Thankyou'Forbuying a Fisher & Paykel Active Smart T,'refrigerator with automatic ice disper/sing
and chilled water through the door.
At Fisher & PaykeEwe are very proud of this refrigerator. We feel we have achieved water
dispensing through the door without compromising the storage space or access in the fridge.
During our testing we have enjoyed the health benefits of having cool filtered water so
accessible, whiEe minimising the number of door openings.
Thousands of hours of food car__'research and 70 years of refrigeration experience, has been
programmed into your refrigerator to give you the best possible performance.
We hope you enjoy your new refrigerator.
Before you start using your Bce& Water refrigerator
Check refrigerator is switched on and has cooled for at least 2 hours (refer to page 15 The
temperature of your refrigerator and freezer) before use.
Check that the water filter has been connected and turned on.
Turn on ice maker
At first use allow approximately 1 minute from when the dispensing pad is pushed until water
is dispensed.This will allow the tank to fill.
Run through and discard the first _ qt or 3 Lof water from the dispenser (refer to page 10
- First use).
Discard the first bin of ice (refer to page 11 - First use).
You are now ready to enjoy ice and water from your Active Smorf" refrige_'rator.
P4g 26 - 49

Safety a_sdwarnings
Installation instru(:dons
All about dse display
Using yo_ir water dispenser
Using your i(e make_
Measu_ed Fill
F_eeze_Clfill a_d Bollle Chili
Tlse lempelalure o1'you_ _el'ligelato_ an8 f_eezel
Wa _et filter
Measured Fill Calibration
Cleansing and cadng for your refrigerator
Filter performance data sheet
2
4
8
10
11
lS
lS
14
15
16
18
2O
21
2S
2S
24
This ice & Water refrigerator booklet cont'ains specific information a_out @e £e and water
P_ease use 8his booklet in conjunction with 8heRefrigerator & Freezer User Guide supplied with
SAW THESEINSTRUCTIONS
The models shown in this user guide may not be available n all markets and are subject to
change at any time For current details about model and specification availability in your country,
please go to our website www,fisherpaykel,com or contact your local Fisher & PaykeJ dealer,

Safety and wallNrfings
To reduce the risk of fire, electric shock, or injury to persons read the IMPORTANT SAFETY
PRECAUT ONS before operating this appliance.
Use this appliance only for its intended purpose as described in this User Guide.
When using this appfiance always exercise basic safety precautions including the following:
This appfiance is not intended for use by young children or infirm persons without supervision
Young children should be supervised to ensure they do not play with the appliance.
Risk of child entrapment. Before you throw away your oM refrigerator or freezer:
-Take offthe doors
-Leave the shelves in place so that children may not easily climb inside.
Extreme care must be taken when disposing of your old appliance to avoid hazards. The
refrigerant gas must be safely removed and for the safety of young chiMren, rentove doors.
Your Fisher &Paykel Appliances Authorised Service Center will be able to give advice on
environmentally friendly methods of disposing of your old re&oera_or or &eezer.
Electrica_
This appfiance must be properly ins tailed in accordance with rite instafladon instructions before
it is used.
Never unplug your refrigerator or freezer by pulling on the power cord.
Always grip the plug firmly and pull straight out from the outlet.
Do not plug in any other appliance at the some power point as your refrigerator or freezer or use
extension cords or double adapters.
Repair or replace immediately aft electric service cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion along its length or at either the plug
or appliance end.
If the power supply cord is damaged, it rnust only be replaced by your Fisher &Paykel Appliances
Authorised Service Center because special purpose tools are required.
When moving your appflance away from the wall, be careful not to rod over or damage the power
cord.
Unplug your refrigerator or freezer before cleaning or repladng the fightbulb.

Sa'fety and wa IrniIIr")gs
Storhg food arid drinks
Never store volatile or flammable materials in your raft@orator or freezer as they [nay explode.
Never freeze liquids in gloss containers. Liquid expands during freezing, which may cause the
container to explode.
Never freeze carbonated drinks. They may explode.
Do not consume food flit is too coM. Food removed from the freezer compartment may be cold
enough to cause damage when brought into contact with bare skin e,g. frozen ice cubes.
Power failure - food safety
Do not refreeze frozen foods that have thawed completely. Follow the recommendations below if
you discover food in },our freezer has thawed:
1)£e crystMs still visible - food may be refrozen but should be stored for a shorter period than
recommended.
2) Thawed but refrigerator cam - refreezing generally not recommended. Fruits and some
cooked food can be refrozen but use as soon as possible. Meat, fish, poultry -use immediately or
cook then refreeze. Vegetables -dJ_ca_d as they usually go limp and soggy.
3) Thawed but warmer than 38 °F (4 °C). Red meat can be cooked immediately and refrozen but
use as soon as possible. Discard all other frozen foods.
Do not refreeze frozen foods that have thawed completely. The food may be dangerous to eat
Many commercially available cleaning products contain solvents which [nay attack plast£
components of your refrigerator or freezer and cause them to crack. Please refer to the cleaning
care secdon of this booklet for further advice.
SAVE THESEINSTRUCTIONS

nstaHation ilnstllructions
Contents of kit
1 13 ft (4 m) white Va"(6 ram) tubing
2 1 xS"(2OOmm) bluetubing
s 1 x pressure reducing valve (PRV)
4 1 x double sided foam
5 2 x locking keys
6 1 x water filter cartridge and head
7 1 x faucet connection - USA market --7/W'UNS
- All other markets - Y/' (15 ram) BSP
3 4 5
£g, 1Wuler connedion kff
it is imperative the pressure reducing valve (PRW is fitted prior to the filter. This vMve ensures
the water wdl not flow bad< into the mains from the refrigerator water system, if the PRY is nat
fitted to the connection line your ice & Water refrigerator features may not funcdon in some
circumstances.
it is recommended that an authorised plumber in your state or town is used to install the water
connection,
The new tubings supplied with the machine are ta be use& old tubings should not be use&
Installation precautions/warning
DO NOT use w#h wa_er tba_ is micrabiaHagicaHy unsafe or of unknown quafity without
adequaCe didnfectian befare or after the system,
WARNING - connect to potable water supply on/y,
DO NOT instafl on fine pressure above gO0 kPa (130 psi) or below 1.50 kPa (22 psi).
DO NOT use on hot water supply (IO0°F [.38°C max.]).
DO NOT install near electrical wires or water pipes that will be in the path of drilling when
selecting the location of filter system.
DO NOT mount filter in such a posit.ion so that it will be struck by other items, such as
wastebaskets, etc,
DO NOT install the filter in direct sunlight as prolonged exposure to Ioht can weaken plastic
cornponents.
DO NOT install in a location that is susceptible to freezing temperatures as damage to the
housing couM occur.
DO NOT screw filter to &idge.

IIIl staHati©llL illr stlructiolr s
InstaHatior_ instructior_s:
1 Ensure that refrigerator is not plugged into a power supply,
2 Remove compartment cover from the rear if present,
:3 Locate isolation faucet for water connection -cold water
f___edonly (dishwasher or sink mixer 'faucets) -- if you cant
find the connection faucet, contact an authorised plumber
in your state or town to fit your water connection,
4 Connect the 8"(200 ram) blue tubing to the outlet of the
PRV (blue toilet) and the inlet connection of the water filter
cartridge as shown in Diagram 1, Gently pull on both ends
to ensure it is locked,
_ Connect the white V4"(6 mm) tubing to the outlet of the
water filter cartridge as shown in Diagram 2, Gently pule to
ensure it is locked,
6Measure the required length of tubing to run from the PRV
to the water connection point
7 Cut the tubing making sure the ends are square and dean
8 Connect the tubing to the faucet connection and the base
of the PRV (white toilet) and then to the faucet as shown
in Diagram 3 Please note that the faucet connection
supplied should fit most installation situations, If your c_r_-_
faucet requires a different fitting, please contact an .__(_ ._i_=\_
authorised plumber in your state or town to purchase ..........._'!1 _, ,__.Si;I_: ==_
the correct fitting, __ I/ _'-----
Conoectonelockingkeytoeachsideofthew0ter I /
I /
filter cartridge in between the cartridge and the -'_ _'_i /
lock ng toilet as shown n Diagram 4, li IT[ I J
lo To fiush the water filter and check for eaks, aimthe II L.I [ _r,
end of the tubing into abucket, tum isolating faucet _,. )) / /
on and run at least _ qt (3 liters) of water through, Once "q]t-: c-z_/.........
complete, turn isolating faucet off. Diagram 3
11 Locate desired position for water filter noting carefully the Fig.4f_uce_conn_cdon
following points:
It is recommended to fit the filter in a vertical
orientation with the water filter head at the top, This will
minimize water leakage when replacing cartridge,
Ensure the filter is in a convenient location to access
every 6 months for replacement, We suggest that
this location is beside the water filter supply faucet in
the cupboard beside the refrigerator
A minimum clearance of 2 V/'(64 ram) from the
bottom of the filter cartridge is required to perform
cartridge removal
Do not screw filter to fridge,
Diagram 2
fig.3 WQler/ ne cor}nection
Diagram 1
F7g.2PRVconrle(liorl

nstalHation inst,ructions
12 Attach double sided foam to the back of the water filter head as shown
in Diagram 5 Write the date to be replaced on the filter (date installed +
6 months). Remove double sided foam backing and attach filter to the
desired position as located in step 11 (refer to previous page).
ls Run the P/'(6 ram) tubing to back of the ffidge ensuring there is enough
tubing to pull out the refrigerator for service.
14 Connect tubing into the water (solenoid) valve located on the right hand
side of the unit (compressor) compartment as shown in Diagram 7, Beware
of hot pipes.
15 Pull gently on tubing to ensure it is locked in as shown n Diagram 8.
Replace compressor cover if present.
16 The completed installation should look like Diagram 9 on page 7.
Diagram 5
£g.6 Double £d_d
fo_m olto@menl
Diagram 7 Diagram 8
Diagram 6
17 Turn isolating faucet on and check that all connections are dry and free of drips
ls Coil water line tubing behind the fridge. Push your refrigerator into place being careful not to
kink or squash the water line running into the water (solenoid) valve.
19 Turn on refrigerator.
20 The first time you require water out of the dispenser, there will be a delay while the water
reservoir fills up. As this is happening, the _ symbol wll flash. Once the reservoir is furl, this
symbol will stop flashing.
21 Run a further 3 qt (3 liters) through the system to ensure the reservoir is flushed out.
22 You are now ready to enjoy chilled water and ice dispensing from your Active Smdrt "_'refrigerator.

Importand
AHconnec_ior,_mu_tbecheckedfor_euk_. [
Ifun_ureofconnectionproce_un_,,'or_euk_thencon_'uctyour_ocu_plumbertoin_uHun_chec_
_he_y_emfory?u.
_nsurewhite_ _6mm,__,bin9i_route_awuyfromshurpobjects,sharpcorners_'_e_ureo_
_inkin_tu_eu_thiswiHs_opwu_erf_ow,_,c_eoroftheref.'_erutoruni_compurtmentandnotinu :}
_oc_io,whereitcur,_es_u_she_. ,, i:i:}
En_ureoHpu#,.f_tconnectionsaref_rmep_,shedintop_ce_hetu_eshouldpushin_ (20mm,_ ::
_eforereuchin_the_op.
,ftu_in_isren,ove_o_on_point,reocu_theon_on_re,nse..,u_in_mu__ofuH_,nserto_to
avoid leaks_
To remove tube from connection points, turn off the isMating faucet, push in the co/let end
gently pull tubing at the seine time
Fig.8 Connection lo waler supply
Diagram 9
System tested and certified by NSF International against NSF/ANSI Standard 53 for the reduction
of Asbestos, Atrazine Benzene, Cyst, Carbofuran, Lead, Lindane Mercury, P Dichlorobenzene
Toxaphene &Turbidity; against Standard NSF/ANSI 42 for the reduction of Chlorine Taste and
Odor and Nominal Particulate Class I to a capacity of 750 gallons (2,838 Liters),

AIHabout the diSllP ay
The display screen enables you to view and modify all the features and options on your ffidge,
For example, you can change the temperature in your fridge or freezer, and select the Freezer
Chill function when you want to quickEy freeze meat You may want a measured amount of
chilled water when you are cooking, or want to quickly chill a bottle of wine when friends
arrive unexpectedEy.
5 6 7 8 9
12 3
Fig.9Electronic control panel
For more detailed information on these functions please refer to pages 10 - 17,
1. Measured Fi[[ (see page 13)
Enables you to select the amount of water to be dispensed,
2. Main menu
_ Scrolls through the main menu (Chill, Temperature, Ice and Settings).
_ _ 3. A_row keys
Scrolls through the settings of each func'don

AII[Iabout the displlay
@
4, Measured Fill {see page 13)
Apre--measuredvolume of water can be selected and dispensed
5, Dispe[_sing water {see page I0}
Animation shows you water isbeing dispensed,
6, Chill {see pages 14-15)
Freezer Chill
When activated this feature boosts cooling in your freezer,
optimising the rate at which your foods are frozen,
Bottle Chill
Your drinks can be chilled more rapidly using this function An alarm
will alert you when they are ready,
7 "Temperature (see page 15)
The temperature setting can be individually adjusted for each
compartment
8_ Ice {see page 11}
The ice making function can be turned on or off,
metn'c 9 Settings/User alerts (see page 16)
Water conversion
US Your volume can be displayed as either US or metric units,
Key Silent Mode
÷Av All key presses can be silenced
Key and dispenser lock
Dispenser lock - disables the buttons and prevents water from being
dispensed,
Key lock -- disables the buttons.
Sabbath Mode
Can be activated if necessary (refer to page 16),

Using youlr watelr dispenselr
Dispensing pad
Your water dispenser has been designed for one handed operation Simply push your glass
up against the dispenser pad found at the back of the dispenser area. This pad requires only a
gentle press to activate.
Please remember that pressing very hard against the dispensing pad will not make the dispenser
operate faster or produce greater quantities of water.
First use
After installation, on the first use, allow approximately a one minute delay from when the
dispensing pad is pushed until water is dispensed.This will allow the tank to fill compbtely.
The _ symbol will flash while the water reservoir fills up. Once the reservoir is full, the symbol
will stop flashing,
After you fill the tank for the first time dispense and discard approximately 3 qt or 3 Lto flush
the tank out,
$
Unless Measured Fill is selected, water will be dispensed in
free--flow mode (For more information on Measured Fill refer
to page 13)
To dispense water push the dispensing pad gently, using a
glass or container.
When you dispense water, a light will appear above the
dispe;lsing area, and on the display screen. The water fil[
icon i_ will also appear
To stop the flow of water simply pull your glass away from
the dispensing pad,
S ................
°"T_J
6<% 6 $
To dvoid ddmdge to property or persone/ injury do not put/rands, fingers or objects up the
dispenser opening.

USillSg you_" ice makel _]
Your ice maker is designed to automatically dispense ice until
it senses that the bin is fill. So the more ice you use, the more it
makes. It is even clever enough to sense when there is nothing
there to catch the ice
First use
When you first turn your refrigerator on. the ice maker will be off.
To turn your ice maker on use the _ button to scroll to the_
screen.
Use the < or _ button to turn the ice maker on or off.
Shows the ice maker s on.
Shows the ice maker is off.
If the bin is full. or inserted incorrectly the ice maker will not
operate When the bin is inserted correctly the scoop will be on
the right hand side of the bin (refer to Fig.12 on page 12). If the bin
is removed the ice maker will not operate
Once your ice maker is in operation, discard the first bin of ce
cubes. This will flush away any irnpurities in the water line and
ensure that you get the best quality ice We recommend that you
also do this after vacations or extended periods of not using ice.
We recommend that you turn the ce maker off if:
- The water supply is to be off for several hours or
- The ice storage bin is to be removed for a period of time or
- You are going on holiday/vacation.
................................. J
S ................................
,.Frl_ _.<::-_ J
,_:Tg.11 Fuming icemaker on
Noises
If this is your first ice maker, you will hear occasional sounds that may be unfamiliar. They are
normal ice making sounds and are not cause for concern.
The following sounds are normal with the operation of an ice maker:
- Motor operation (low humming).
- Running water.
- Water valve opening and closing (hissing sound),
- Ice being bosened from tray (cracking).
- Ice dropping into bin (clunking),

Using youlr ice malkelr
Information about you_ ice maker
The ice cube tray will fill with water after the freezer has reached the correct temperature, First
cubes will normally freeze after several hours
When cubes are frozen, they will be ejected from the mould into the ice storage bin,
Ice making will continue until the storage bin is full
ice making will resume when the ice is used.
For maximum ice storage, levd the stored cubes with the ice scoop.
'four Ice & Water product comes wth a smaller ce bin inside the larger freezer bin, Attached to
this s a scoop for the ice,
IfaJargeamountofice srequired, remove the smaJler storage bin and aJlow ice to faH into the
larger bin,
If ice is not used often, old cubes will become cloudy and taste stale and will shrink. Empty the
ice storage bin periodically and wash in lukewarm water, Dry thoroughly and place back,
\
Fig.72Icesrorogebin ond scoop
in corr,>orposilion
Avoid contact with the moving parts of the elector mechanism, and do not place your fingers on
the automatic ice making mechanism while the refigerator is plugged in.
Do not use ice cubes that may have become discolored, usually with a greenoblue color. If such
dis.coloration is noted, discard the ice cubes and contact your local authorized service center.
Ensure the ice maker is connected to the filter and to adrinkable water supply only.
Installation of the water connection to the ice maker must be completed by a qualified service
technician (see instdllation instructions),

IIFddge options _iJ
_ Measured Fill
One useful feature of your water dispenser is its ability to dispense a pre-rneasured amount of
water. This comes in handy when cooking or preparing drinks.
Press the _n button to highlight the screen and again to cyde through the
preset quantities.
iU .............................................
jj o
Ji ilji
__J
Fig.I4 Me_ricdisploy
Push the dispensing pad to receive the pre--sdected quantity of chilled water.
if you stop dispensing part way through your pre selected quantity the dispenser wiEI
remember the remaining quantity to be dispensed for a short time. Simply continue by pressing
the pad.
The _ and _ buttons can be used to increase or decrease the pre-set measurements in 1 oz, or
25 mJ increments, to a maximum of 1 qt, or 1 L.
Changing the Measured Fill units
The pre-set measurements can be displayed in US imperial or metric units.
The unit setting can be changed by pressing the _ button to scroll to the screen and
pressing the _ and _ buttons until the desired units are displayed. To return to the Measured
Fill option, press the _j1 button.

Fddge ©llPtions
_v
freezer _
_@ Freezer Chill
We know that the faster food isfrozen, the better the overall quality of the food, so we have
created the FreezerChill feature.
The Freezer Chill feature drops the freezer to it's coldest temperature for a 12 hour period and
then returns to ts normal mode. Ytou may wish to use this when freezing a quantity of meat or
when you are making frozen desserts.
To activate, use the _ button to scroll to the screen. Then use the @ button until
_m;r _ is displayed.
To deactivate manually, use the _ button to scroll to the screen. Then use the
@
and _ buttons until there is no *'..... _' icon in the screen.
For best results, we recommend that you activate the funcdon approximately 2 hours before it is
required. Alternatively, activate it when placing food into the freezer.
bottle Bottle Chill
This function allows you to chill your beverages in the freezer without the worry of forgetting
about them.
When activated Bottle Chill will remind you to remove your bottle by sounding an alarm, The
user alarm will continue to sound until any key on the panel is pressed.
The tirne taken to chill depends on the size of your bottle. Bottle Chill allows you to customise
this chill time.
Recommended times:
20 minutes - can or small bottle.
25 minutes --wine bottle or similar size beverage
30 minutes - larger bottle.
If you remove your beverage from the freezer and it is not chilled to your liking, reset the timer
to 10 minutes and place the beverage back into the freezer.
To activate, use the _ button to scroll to the screen, Then use the @ button until
is displayed.
Then use the _ button to select 10, 15, 20, 25 or 30 minutes as displayed on the left hand side of
the screen in the _JtEAS_dRED FiLLI screen.
An alarm will sound after the amount of time selected has dapsed.

IF,ridge options
Bottle Chili contd_
Do no_ leave _:hehorde inside the freezer longer than the time needed for chillhtg.
To deactivate manually use the _w button to scroll to the screen then use the
and } buttons until there is no con in the screen.
Note: The freezer chiJ{ and bottle chill option cannot be used at the same time.
The temperature of your refrigerator and freezer
When the refrigerator is first turned on it will take approximately 2 to 3 hours to cool,
depending on the humidity and temperature of the environment.
To adjust the temperature of a compartment, use the _ button to scroll to the
screen, use the _ button to select the compartment to change
The temperature can then be adjusted using the _ button to make the compartment warmer
or the _ button to make the compartment colder.
The temperature setting will be indicated on the icon bdow.
]
W_f'l',*lef
It is important to have your refrigerator set to the correct temperature. Setting it too cold may
cause some items in the refrigerator to freeze, and setting it too warm will decrease the storage
life of your food.
For further information on food storage temperatures refer to the food care section in the
general Refrigeration & Freezer User Guide.

Fddge options
Water unit conversion
Yeu can change the units your refrigerator uses between USand metric units. To change the
units press the _ button to scroll to the screen option and press one of the _ or
buttons until the desired units are displayed.
_eX Key Silent Mode
The Key Silent Mode allows you to silence all key presses.
It can be activated or deactivated by holding the _ button for four seconds.
When Key Silent Mode is on 4°× will appear
When this function is off no symbol will appear.
Note: Faults, Bottle Chill timer and the door alarm will still sound when the refrigerator is set on
Key Silent Mode.
Key and dispenser lock
The dispenser lock disables the buttons and prevents
water from being dispensed.
Key lock disables the buttons.
Activate by holding down both the _da button and the
_b g thuttonto e er,
After 2 seconds _ icon will appear indicating dispenser
lock is activated
After 2 rnore seconds _ icon will appear indicating key
lock is activated
To de--activate, hold down both the _j'l button and the
button together for 2 seconds.
Sabbath Mode
In Sabbath Mode alarms, lights and displays are
deactivated.
Sabbath Mode can be activated or deactivated by
holding down the 'L_q ,_ and _ button for 4 seconds.
U
Fig. 15 K_*yand dispenser Io k
Fig.ld _abbalh Mode

Flridge options
Once in Sabbath Mode:
The interior light wiJJnot turn on when the refrigerator is opened.
The door alarm will not operate
The display wiJJ not be illuminated
Electronic control panel will not work.
Note: If power is turned off the refrigerator will automaticall r continue in Sabbath Mode once
power is restored, Sabbath Mode will automatically de.activate after 80 hours,
Your refrigerator is clever enough to diagnose it's own problems, It will alert you when there is
a fault,
_._) No water
The no water icon _ wiJJappear when the water supply to the refrigerator is interrupted,
Please refer to the Trouble shooting checklist (refer to pages 21 -22).
@ FHter reset
The filter reset icon @ will appear when the water filter needs changing, This will flash when
dispensing water, To change the filter and reset the filter icon refer to pages 18 -1g,
Fau_t
In the unJikdy event a fauJt occurs the _ con appears on the front of the disphy and a fauJt
code will be displayed on the left in the [_aEA$UREDFILLl screen,
When the door is open the refrigerator fault alarm will sound, To silence this press any button
on the display,
Please take note of the fault code and contact our Customer Care Center, Details of Customer
Care phone numbers can Le found in the back of the general Refrigeration & Freezer User Guide,
__:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::'lJ
IF30
Fig, 17/:slult code disg/oy

Watelr filltelr
All the water to your fddge is filtered to remove impunties through a cartridge located in a
position of },,our choice outside the refrigerator Of course, this will need changing approximatdy
every 6 months or up to 740 gallons (2800 L) depending on the quality of the incoming water
and how much you use the dispenser_
There is a replacement indicator @ icon on the control panel which will appear when the filter
needs replacing It wiJJflash, when dispensing water, as a reminder,
Replacement cartridges are available from your authorbed Fisher & Paykd Dealer, The details of
the replacement cartridge are on the label on the cartridge,
Changing the water filter cartridge
1Grasp and firmly twist the cartridge in an anticlockwise direction (to the left when installed in
the recommended orientation) as shown in Diagram 1,
2 Pull the cartridge away from the filter head (down when installed in the recommended
orientation) as shown in Diagram 2,
- It is not unusual for a few drops of water to be present when liter is removed,
S Discard old filter.
4 Filter installation;
---- Remove protective cap on spigot on head.
--- Push the cartridge up towards filter head while rotating it in a clockwise direction (to the right
when installed in the recommended orientation) as shown in Diagram 3.
5 Reset filter indicator icon on the display (this will set to remind you when the filter is due to be
replaced again) Refer to page 19
6 Dispense 5 qt /5 L to flush the cartridge, removing trapped air and harmless carbon fines
7 A few drips may appear out of the dispenser over the next few days as the remaining trapped air
is cleared.
Diag Diagram 5 \
Fig. 78 Changing th,>wal _r fil_,>rcorlridge