Fisher-Price T4146 User manual

Newborn Baby
Toddler
www.fisher-price.co.uk
T4146
Older Baby
WARNING
IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE.

2
WARNING
CAUTION
To prevent serious injury or death:
Fall Hazard -• It is dangerous to use this
product on an elevated surface, since child’s
movement may cause the product to slide
or tip over. Use only on a floor.
Suffocation Hazard -• Never use on a soft
surface (bed, sofa, cushion) since the
product can tip over and cause suffocation
in soft surfaces.
Never leave child unattended.•
Never use as a carrier or lift while child•
is seated.
Use the upright position only when child has•
developed enough upper body control to sit
without leaning forward.
Always use the restraint system until•
child is able to climb in and out of the
product unassisted.
Reclined position not recommended for•
children who can sit up by themselves
(6 months approximately, until 9 Kg/20lbs).
Never use toy bar as a handle.•
Consumer Information
This package contains small parts in its
unassembled state. Adult assembly is required.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required. Tool needed for assembly: Phillips
screwdriver (not included).
• Requires one “D” (LR20) alkaline battery (not included) for
soother operation.
• Product features and decorations may vary from photographs.
IMPORTANT! Please remove all parts from the package and identify
them before assembly.
Pad with Seat Back Tube
Hint: Please refer to the care
section to remove the seat back
tube for cleaning.
Toy Bar Front Bar
2 Side Rails Crossbar
Note: Tighten or loosen the screws with a Phillips screwdriver.
Do not over-tighten the screws.
#4 x 20 mm Screws – 6
Parts
Shown Actual Size

3
Assembly
• Place the side rails on a flat surface.
• Fit the crossbar tabs into the small rectangular opening in each
side rail. Push the crossbar down completely.
• Insert two screws into the crossbar and tighten.
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price®
for replacement parts and instructions if needed. Never substitute parts.
Side Rails
Crossbar
1
• First lift the front rails and then push out the back rails.
LIFT
PUSH
LIFT
PUSH
2
Side Rails
Front Bar
Hint:You may want to install batteries into the soother before
assembling the front bar to the front rails.
• Position the front bar so that the soother is upright. Fit it to grooved
area on the inside of the front rails.
• Insert four screws into the front rails and tighten.
Hint: You may need the help of another adult to hold the front bar
in place while you insert and fasten the screws.
4
• Insert and "snap" the back rails into the sockets in the side rails.
Pull up on the back rails to be sure they are secure.
3

4
• Insert the ends of the seat back tube (inside the pad) into the
sockets in the front rail. Push down on the seat back tube until you
hear a “click” on each side.
• Pull up on the seat back tube to be sure it is secure.
Pad
Seat Back Tube
Socket
Socket
Assembly
5
• Locate the pocket in the bottom of the pad.
• Fit the hardboard (attached to the front bar) into the pocket in
the pad.
Pocket
Hardboard
6
• Fit the clips on the front edge of the pad to the bottom edge of the
front bar.
Clips
• Wrap a pad flap around a front rail and fasten the buckle. Make
sure you hear a “click”.
• Repeat this procedure to fasten the other pad flap.
Pad Flap
Buckle
7
8

5
Assembly
• Fit the toy bar clamp to the top of the front rail. Push the toy bar
clamp down to “snap” it into place.
Hint: To remove the toy bar, lift the edge of the clamp and pull
to remove.
Toy Bar
Clamp
9
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
Battery Installation
• Turn the product face down.
• Loosen the screw in the battery compartment door with
a Phillips screwdriver and remove the battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
Hint: We recommend using an alkaline battery for longer battery life.
• Replace the battery compartment door and tighten the screw.
• If this product begins to operate erratically, you may need to reset
the electronics. Slide the power switch off and then back on.
IMPORTANT! If vibrations become faint, or if there are no
vibrations, remove the “D” (LR20) battery from the soothing unit
and dispose of it properly. Replace the battery with a new “D”
(LR20) alkaline battery.
1,5V x 1
"D" (LR20)
+-
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.

6
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
PRINTED IN CHINA T4146pr-0726
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.

7
Newborn-to-Toddler Portable Rocker
Newborn Baby
Toddler
Older Baby

8
WARNING
Upright
• Fasten the straps on the back of the seat. Make sure you hear
a “click”.
Recline
• Unfasten the straps on the back of the seat.
To prevent serious injury or death: Use
the upright position only when child has
developed enough upper body control to sit
without leaning forward.
RECLINE
Setup
Strap
Straps
UPRIGHT
WARNING
Seat
• Pull the tab on each front kickstand out and then rotate the
kickstand down.
• Rotate the rear kickstands down.
Kickstand
Kickstand
Rocker
• Rotate the front and the rear kickstands inward.
To prevent serious injury or death:
• Fall Hazard - Never use on any elevated
surface, since child’s movement may cause
the product to slide or tip over. Use only on
a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since the
product can tip over and cause suffocation
in soft surfaces.
SEAT
ROCKER

9
LIFT
Extend Frame
• Lift the seat back to extend the frame for toddler use.
Shorten Frame
• While pressing the buttons on the back of the frame, push the
seat back to shorten the frame for newborn or older baby use.
PUSH
PRESS
PRESS
Setup
WARNING
Toy Bar
Clamp
Toy Bar
• Fit the toy bar clamp to the top of the front rail. Push the toy bar
clamp down to “snap” it into place.
Hint: To remove the toy bar, lift the edge of the clamp and pull
to remove.
To prevent serious injury or death: Never
use the toy bar as a handle.
EXTEND FRAME
SHORTEN FRAME

10
WARNING
To prevent serious injury or death:
• Never leave child unattended.
• Never use as a carrier or lift while child
is seated.
• Always use the restraint system until
child is able to climb in and out of the
product unassisted.
Secure Your Child
• Turn the toy bar out of the way or remove it altogether.
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten the waist belts to each side of the restraint pad. Make sure
you hear a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
Waist Belt Waist Belt
Restraint Pad
1
Anchored End
Free End
To tighten:
• Feed the anchored end of the waist belt up through the buckle to
form a loop A. Pull the free end of the waist belt B.
To loosen:
• Feed the free end of the waist belt up through the buckle to form
a loop A. Enlarge the loop by pulling on the end of the loop
toward the buckle. Pull the anchored end of the waist belt to
shorten the free end of the waist belt B.
• Tighten each waist belt so that the restraint system is snug against
your child. Please refer to the next section for instructions to
tighten the waist belts.
Anchored End
Free End
TIGHTEN LOOSEN
3
2

11
Soothing Vibrations and Fun Music Fold for Portability and Storage
• Lift the back rails from the side rails.
LIFT
• Press both frame release buttons.
PRESS
1
2
• Make sure your child is properly secured in the seat.
• Slide the power switch on the soothing unit to for vibrations
and Oto turn vibrations off.
Note: If vibrations from the soothing unit become faint, or if there
are no vibrations, remove the battery from the soothing unit and
dispose of it properly. Replace the battery with a new “D” (LR20)
alkaline battery.

12
• Push the back rails toward the front rails.
PUSH
LOWER
3
• Lower the seat back.
4
Fold for Portability and Storage Care
• The pad is machine washable. Wash it separately in cold water
on the gentle cycle. Do not use bleach. Tumble dry separately on
low heat and remove promptly. The frame, toy bar and toys may
be wiped clean using a mild cleaning solution and a damp cloth.
Do not use bleach. Do not use harsh or abrasive cleaners. Rinse
clean with water to remove residue. Do not immerse the frame or
the toys.
To remove the pad:
• Unfasten the pad flaps.
• Remove the pad clips from the front bar.
• Remove the hardboard from the pocket in the pad.
• Press the seat back tube release buttons on each side of the front
rails. Pull to remove the seat back tube. Remove the seat back
tube from the sleeve in the pad.
To replace the pad, first insert the seat back tube into the sleeve in
the top of the pad. Then, follow the assembly instructions.
PRESS
PRESS