Fisher-Price 79534 User manual

Model Number: 79534, 79545, 79546
Please save these instructions for future reference.
Tool needed for assembly: Phillips Screwdriver (not included).
Use only for a child who is unable to push up on hands and knees, pull up or sit unassisted.
BOUNCE ’N PLAY
ACTIVITY DOME
Product features may vary from picture above.

Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free, rather than
return this product to the store. Usually we can solve the problem on the telephone or by sending you replacement parts. Please call
Fisher-Price® Consumer Relations, toll-free at 1-800-432-KIDS, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers
using TTY/TDD equipment, please call 1-800-382-7470. Or, write to: Fisher-Price® Consumer Relations, 636 Girard Avenue, East Aurora,
New York 14052.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
• Never leave child unattended.
• To prevent suffocation from entrapment, use only the Fisher-Price®pad
provided. Never use additional padding or mattress.
• To prevent falls, use only for a child who is unable to push up on hands
and knees, pull up or sit unassisted.
• To prevent strangulation:
_Never place items with a string, such as hood strings or pacifier cords,
around a child's neck.
_Never place this product near a window where cords from blinds or
drapes can strangle a child.
• Never place product on an elevated surface.
• Never move or carry this product with a child in it. This product is not
designed to be used as a carrier and will become unstable.
• The Bounce ’n Play Activity Dome must be fully erected prior to each use.
• Never use plastic shipping bags or other plastic film as mattress covers.
They can cause suffocation.
WARNING
CONSUMER INFORMATION
WARNINGS
2

Base
Pad
Metal Canopy Stay
3 Toys
(Toys may
be different
than shown)
2 Base Wires
®
®
2 Covers
Plastic Mesh Cover Stay
In its unassembled state, this
product contains small parts.
Adult assembly is required.
CAUTION
PARTS
3
M5 x 113/16" Screw - 2
M5 Lock Nut - 2
M6 x 15/8" Screw - 8
M6 Lock Nut - 8
SHOWN ACTUAL SIZE
Spring - 4

• Insert an M6 x 15/8" screw through each frame tube and into
the frame.
• Fit an M6 lock nut (so that the protruding side is toward the
fabric) into each middle opening on the back of the frame.
Metal
Canopy
Stay
• Insert the metal canopy stay through the canopy tunnel.
• Open the base and position it upright on a flat surface,
as shown.
• Locate the end of the base with the mesh cover. Insert the
entire plastic mesh cover stay into one of the button holes
in the mesh cover.
• Be sure to tuck the plastic mesh cover stay away from the
button hole in the mesh cover.
Frame Tube Frame Tube
• Position the ends of the frame tubes against the middle holes
in a frame.
IMPORTANT! Before each use or assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed.
Never substitute parts.
M6 Lock Nut
Canopy Tunnel
Middle Hole Middle Hole
Frame
Frame
Frame Tube
Frame Tube
M6 x 15/8" Screw - 4 M6 Lock Nut - 4
Base
Mesh Cover
Button Hole Plastic Mesh
Cover Stay
Protruding
Side
4
ASSEMBLY
1
2
3
4

• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other ends of the frame
tubes to the frame on the other side of the base.
• Position the base wires around the base so that the ends point
upward and are against the lower holes in a frame.
• Place a spring onto an M6 x 15/8” screw.
• Insert the M6 x 15/8" screw with spring through a base wire and
into the frame.
• Fit an M6 lock nut (so that the protruding side is toward the
fabric) into each lower hexagonal opening on the back of
the frame.
• Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other ends of the base
wires to the frame on the other side of the base.
Base Wire
Lower Hole
Spring
Frame
• Position one end of the metal canopy stay against the upper
hole in a frame.
• Insert an M5 x 113/16" screw through the hole in the cover.
• Fit the end of the screw through the hole in the metal canopy
stay and into the upper hole in the frame.
• Push on the cover to insert and “snap” the tab on the cover into
the slot in the frame. Make sure you hear a “snap”.
• Fit an M5 lock nut (so that the protruding side is toward the
fabric) into the upper hexagonal opening on the back of
the frame.
• Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
• Repeat this procedure to attach the other end of the metal
canopy stay and the remaining cover to the frame on the other
side of the base.
Upper
Hole
Cover
Slot Tab
Lower Hole
M5 x 113/16" Screw -2
Metal Canopy Stay
M6 x 15/8" Screw - 4
M5 Lock Nut -2
Protruding
Side
Protruding Side
M6 Lock Nut - 4
5
5
ASSEMBLY
6
7
Spring - 4

®
• Fasten the pad fasteners to the base fasteners.
• Lift the canopy.
• Attach the toys to the canopy fasteners.
IMPORTANT! Assembly is now complete, but Bounce ‘n Play
Activity Dome is not ready for use. Please refer to the Use
instructions, on this page, beginning with step 2.
Pad
Fastener
Toys Canopy
Fasteners
Sides of Base Wire
• Position the product upright on a flat surface.
• Grasp both sides of a base wire.
• Pull both sides of the base wire outward and then let the base
wire rotate down.
Note: If the base wire does not freely rotate down, pull the sides
of the base wire further outward.
To Unfold
ASSEMBLY
8
6
USE
1
Frame
Groove Groove
• Lift the product up slightly so that each side of the base wire
“snaps” into the groove in each frame. Make sure you hear
a “snap”.
2
Sides of Base Wire

Using the Canopy
• Push down on the product to be
sure each side of the base wire is
in the correct position. The base
wire should rest in the groove in
each frame.
• Repeat Use steps 1 - 3 to unfold
the other base wire.
Base Wire
Groove
Frame
Correct
®
• Adjust the canopy and mesh cover up.
• While holding the mesh cover up, fasten the zipper closed.
Canopy Up
Mesh Cover Up
Zipper
®
• Adjust the canopy up or down.
Canopy
Down
Canopy Up
Using the Mesh Cover
7
USE
3
4
5
• Grasp both sides of a base wire.
• While lifting the product up slightly, pull both sides of the
base wire outward to remove the base wire from the groove
in each frame.
Frame
Groove Groove
To Fold for Portability
6
Sides of Base Wire

If you have any questions about this product:
In CANADA: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga,
Ontario L5R 3W2. Questions? 1-800-567-7724.
In GREAT BRITAIN: Mattel U.K., Ltd., Helpline: 01628 500303.
In AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond, Victoria 3121 Australia. Consumer Advisory Service 1-800-800-812
(valid only in Australia).
The pad and toys are machine washable. Wash the pad and toys
separately in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly. The
fabric and frame may be wiped clean using a mild cleaning
solution and a damp cloth.
Base Wire
• Rotate the base wire up.
• Repeat this procedure to fold the other base wire.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. 79534F-0920
©2000 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. Printed in Hong Kong
USE
7
CARE