Fisher-Price GDD39 Quick setup guide

ASSEMBLY AND USE
GDD39
Scan it. Watch it.
Build it.
fisher-price.com/assembly/GDD39
EASY
ASSEMBLY
VIDEO

2
WARNING:
Prevent serious injury or death:
•Neverleavechildunattended.
•Thisproductisnotintendedforunsupervisedorprolongedperiodsofsleep.
•Alwaysusetherestraintsystem.
•Neveruseforachildabletositupunassisted.
•Fall Hazard –Neveruseonanyelevatedsurface,sincechild’smovementmay
causetheproducttoslideortipover.Useonlyonafloor.
•Suffocation Hazard–Neveruseonasoftsurface(bed,crib,sofa,cushion)since
theproductcantipoverandcausesuffocation.
•Thetoybarisnotacarryhandle.Neverusetoybartoliftorcarryproduct.
•Neveruseasacarrierorliftwhilechildisseated.

3
BEFORE YOU BEGIN
IMPORTANT!
Keep this instruction sheet for future reference, as it contains
important information.
Before assembly and each use, inspect this product for damaged hardware,
loose joints, missing parts or sharp edges. Do not use the product if any parts
are missing, damaged or broken. Do not use accessories or replacement parts
other than those approved by the manufacturer. Never substitute parts.
Adult assembly is required. Tool needed for assembly: Phillips screwdriver
(not included).
Please read these instructions before assembly and use of this product.
Product features and decorations may vary from images.
Set aside at least 20 minutes for assembly.
One D (LR20) alkaline battery is required for the soother (not included).
For longer life, use alkaline batteries.
20
1,5V
D
(LR20)
x1
Requires an AC adapter (input 100 - 240 VAC, 50 – 60 Hz, with an output of
6V, 1A) for operation (included).
The AC adapter is not a toy.
Use from birth until child is able to sit up unassisted.
This product may come with replacement warning labels which you can apply
over the factory applied warning label if English is not your primary language.
Select the warning label with the appropriate language for you.
Some features of this product only work with the Fisher-Price® Smart
Connect™ app.
Download the Fisher-Price® Smart Connect™ app to control the glider from
your smart device (not included). The app is available on the App Store® and
Google Play™. The app does not control seat vibration.
The Smart Connect™ app is compatible with most iOS and Android™ devices.
Visit fisher-price.com/SmartConnect/ for a list of compatible devices.

4
PARTS
IMPORTANT! Please remove all parts from the package and identify them before assembly.
Some parts may be packed in the pad.
x 2 x 2
We recommend installing batteries
in the soothing unit before
beginning assembly.

5
PARTS
M3,5 x 15 mm Screw
x 8
Note: Tighten or loosen all screws
with a Phillips screwdriver. Do not
over-tighten the screws.

6
ASSEMBLY
1
3
2
Push the base tube until it
“snaps” into place. Pull on
it to be sure it’s assembled
to the base.
Rotate the tube up and
then pull it out. Go back to
assembly step 1.
Oh, no! If you snapped one end of the base
tube into the base and can’t assemble
the other end, you can remove the base
tube. See the next step for instructions to
remove the base tube.

7
ASSEMBLY
4
5
Push the other base tube
until it “snaps” into place.
Pull on it to be sure it’s
assembled to the base.
During shipping, the
seat base tubes may
have moved. Press the
latch and make sure
the ends of the tubes
align on both sides.
6
It’s easier to complete assembly
if the seat base tubes are turned.
If the seat back does
not snap to the tubes,
try assembling it
to the tubes on the
opposite side of the
seat base.

8
7
ASSEMBLY
8
Make sure the socket
is upright.
9
Make sure the socket
is upright.

9
10
Turn the assembly
over and fit a seat rail
to the frame.
11
ASSEMBLY
x 4

10
ASSEMBLY
13
12
x 4

11
ASSEMBLY
14
Turn the assembly
upright to attach the
seat pad.
Hint: Before attaching the seat pad in the next step, you may want to install the soother battery.
Go to page 13 for battery installation instructions.
Attach the pad around
the soother.
15

12
ASSEMBLY
17
16
Fasten the pad button
holes to the pegs.
Buckle the straps on
the pad. Make sure you
hear a “click”.
18
Tuck the pad around the toy bar retainers.

13
19
Fit the restraint belts
through the slots
in the body support.
ASSEMBLY
SOOTHER BATTERY INSTALLATION
The battery compartment is
located on
the underside of the soother.
Remove the seat pad from
around
the soother.
Loosen the screw in the battery
compartment door and lift to
remove the door.
Insert one D (LR20) alkaline
battery.
Replace the battery
compartment door and
tighten the screw.
Replace the seat pad around
the soother.

14
The toy bar is removable.
Simply press the the ends of
the latches and lift the toy bar.
TOY BAR
ADJUST SEAT BACK
The seat back can be raised or lowered for upright or recline seating when used as a rocker
or glider.
Press the latch on the seat frame and then push the seat back or the seat bottom into
upright or recline positions.

15
GLIDER
“Snap” the seat to the
base to use as a glider.
Place the glider near
a standard wall outlet.
First plug the AC adapter into
the glider base and then the
wall outlet.
Use the AC adapter only in
a wall outlet. Do not plug the
adapter into a ceiling outlet.
1
2

16
Before using the Smart Connect™ app for the first time,
you will need to pair your device with the glider.
PAIRING YOUR DEVICE
Open the Smart Connect™ app on your device. Be sure your device is within approximately
1,8 m (6 ft) of the glider to pair.
Press and hold the pairing button (power button) on the glider control panel for about
5 seconds. The glider stays in pairing mode for approximately 30 seconds.
Hint: If you cannot pair your device with the glider, try moving the device closer to
the glider.
The glider icon will be highlighted in green in the app when the glider is connected to your
device. This indicates that you can use your device to control the glider.

17
App features and decorations shown in photographs and illustrations may vary.
SMART CONNECT™ APP
Touch to customize the
glider name.
Touch to connect or
disconnect your device
from the glider.
Touch to increase
gliding speed.
Touch to start settling
music that transitions to
calming music. Make sure
you choose the amount of
time for each stage.
You can save up to two
custom settings.
Touch to start selections
(gliding, sounds or
music). Touch again
to pause.
Touch to decrease
gliding speed.
Choose the amount of
gliding time.
Touch and drag the
button to increase or
decrease volume.
Choose how long you’d
like music or sound
effects to entertain baby.
Touch a button to choose
music or sound effects.

18
RESTRAINT SYSTEM
1
2
Position the restraint pad between your child’s
legs and fasten the restraint belts to each side of
the restraint pad. Make sure you hear a “click” on
both sides.
Check to be sure the restraint system is securely
attached by pulling it away from your child. The
restraint system should remain attached.
Tighten each waist belt so that the restraint
system is snug against your child.
To tighten: Feed the attached end of the restraint
belt into the buckle to form a loop. Then, pull the
free end of the restraint belt.
To loosen: Feed the free end of the restraint belt
into the buckle to form a loop. Then, pull the
anchored end of the restraint belt.

19
3
GLIDER
Touch the power button on the glider
base to turn power ON or OFF.
Touch the speed buttons or to select
the desired gliding speed or to turn gliding
motion off.
Touch or for music or nature sounds.
Touch the same button again and again to
cycle through music or sounds or to turn
music or sounds off.
Touch or to adjust volume up
or down.
If the glider begins to operate erratically,
you may need to reset the electronics.
Unplug the AC adapter from the glider
base and then plug back in again.

20
ROCKER SEAT
SOOTHING VIBRATIONS
Slide the soother power switch to turn
vibrations ON or OFF.
Low battery power or a static charge
may cause the soother to operate
erratically. If vibration does not turn on
or will not turn off, remove and reinstall
the battery. If you still experience
a problem, replace the battery.
Lift to remove the seat
from the base to use as
a rocker.