Fisher-Price V4557 User manual

www.fisher-price.co.uk
V4557
IMPORTANT!
KEEP FOR FUTURE REFERENCE.

2
To prevent serious injury or death:
• Fall Hazard - Never use on any elevated
surface, since child's movement may cause
the product to slide or tip over. Use only on
a floor.
• Suffocation Hazard- Never use on a soft
surface (bed, sofa, cushion) since the product
can tip over and cause suffocation in
soft surfaces.
• Always use restraint system.
• This product is not intended to replace a cot
or bed for prolonged periods of sleep.
• Never leave child unattended.
• Do not use product once child can sit unaided.
• Never use as a car seat.
• Never use toy bar to carry product.
• Never use as a carrier or lift while child
is seated.
WARNING
Consumer Information
IMPORTANT! Please keep this instruction sheet for future reference,
as it contains important information.
• Please read these instructions before assembly and use of this product.
• Adult assembly is required. Tool needed for assembly: Phillips
Screwdriver (not included).
• Requires one "D" (LR20) alkaline battery (not included) for
soothing unit operation.
• Use from birth until child is able to sit upright unassisted.
• The maximum weight for this product is 9 kg (20 lbs).
• This product does not replace a cot or bed. If your child needs to
sleep, place the child in a suitable cot or bed.
• Product features and decorations may vary from photographs.
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked
Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory
Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance
Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Pad
Retainer
Body Support
Left Base Wire
Base Tube
2 Feet
Right Base Wire
Seat Back Tube
Footrest
Retainer
Toy Bar
Parts
IMPORTANT! Please remove all parts from the package and identify
them before assembly. Some parts may be packed in the pad.
Note: Screw shown actual size. Tighten or loosen all screws
with a Phillips screwdriver. Do not over-tighten the screws.
M5 x 20 mm Screw – 4
V4557pr-0726
PRINTED IN CHINA
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.

3
3
1
• Place the base tube on a flat surface.
• Position the left and right base wires as shown.
• Fit the left base wire and right base wire into the base tube.
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price®
for replacement parts and instructions if needed. Never substitute parts.
Right Base Wire
Base Tube
Left Base Wire
2Non-Skid Surface Down
• Position the feet so the non-skid surface is down.
• Fit the feet on the base tube, as shown.
• Insert a screw through each foot and tighten.
Assembly
This package contains small parts in its
unassembled state. Adult assembly is required.
CAUTION

4
5
Assembly
Seat Back Tube
• Fit the seat back tube onto the ends of the base wire.
• Push the seat back tube to be sure it is completely on the
base wires.
6
• Fit a retainer to the outside of the seat back tube, as shown.
Make sure the socket in the retainer is upright.
• Insert a screw through the hole in the seat back tube, base wire
and into the inside of the retainer.
• Repeat this procedure to assemble the other retainer to the other
side of the seat back tube.
• Pull the seat back tube up to be sure it is secure. If you can
remove either end of the seat back tube, you have not assembled
the retainers correctly. Remove the screws, re-read and repeat
Assembly steps 5 and 6.
Retainer Socket Up
7
Pad Seat Back Pocket
• Position the pad above the frame.
• Fit the upper pocket on the back of the pad onto the seat back tube.
4
• Position the footrest so that the soothing unit is upright.
• Fit the footrest onto the ends of the base wires.
Base Wires
Footrest

5
Assembly
8
Pad Lower Pocket
• Lift the footrest. Fit the lower pocket on the back of the pad onto
the footrest.
9
Retainers
• Fit the retainers through the side openings in the pad.
• Fit the edges of the soothing unit through the large opening in the
front of the pad.
Soothing Unit
10
Toy Bar Plugs
Sockets
• Insert and “snap” the toy bar plugs into each retainer socket.
Hint: The toy bar is removable. Press the ends of the latches and
lift the toy bar.
11
• Press the body support strap to the fastener on the back of
the pad.
Hint: You can move the body support up or down for your
baby's comfort.

6
Battery Installation
Hint: We recommend using an alkaline battery for longer
battery life.
+
–1,5V
“D” (LR20)
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
• Pull to remove the pad from around the retainers and the
soothing unit A.
• Remove the pad bottom pocket from the footrest B.
1
B
A
A
• Loosen the screw in the battery compartment door. Remove the
battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
• Replace the battery compartment door and tighten the screw.
• Pull and fit the pad seat bottom pocket around the soothing unit
and footrest.
• If this product begins to operate erratically, you may need to reset
the electronics. Slide the power switch off and then back on.
2
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.

7
1
2
• Tighten each waist belt so that the restraint system is snug against
your child. Please refer to the next section for instructions to
tighten the waist belts.
Restraint System
Restraint Belts
Securing Your Infant
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten the restraint belts to the restraint pad. Make sure you hear
a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
Restraint Pad
Setup and Use
3
To tighten the restraint belts:
• Feed the anchored end of the restraint belt up through the buckle
to form a loop A. Pull the free end of the restraint belt B.
To loosen the restraint belts:
• Feed the free end of the restraint belt up through the buckle to
form a loop A. Enlarge the loop by pulling on the end of the loop
toward the buckle. Pull the anchored end of the restraint belt to
shorten the free end of the restraint belt B.
Anchored End Anchored End
TIGHTEN LOOSEN
Free End Free End
To prevent serious injury or death:
• Fall Hazard - Never use on any elevated
surface, since child's movement may cause
the product to slide or tip over. Use only on
a floor.
• Suffocation Hazard- Never use on a soft
surface (bed, sofa, cushion) since the product
can tip over and cause suffocation in
soft surfaces.
• Always use restraint system.
• Never leave child unattended.
• Do not use product once child can sit unaided.
• This product is not intended to replace a cot
or bed for prolonged periods of sleep.
• Never use as a car seat.
• Never use toy bar to carry product.
• Never use as a carrier or lift while child
is seated.
WARNING

8
Power Switch
• Make sure your child is properly secured in the seat.
• Slide the power switch to: Vibrations or Off.
IMPORTANT! Low battery power causes this product to operate
erratically: no vibrations and the product may not turn off.
Remove and discard the battery and replace with a new
“D” (LR20) alkaline battery.
Soothing Unit Care
B
C
A
A
To remove the pad:
• Pull to remove the pad from around the retainers and the soothing
unit A.
• Remove the bottom pocket of the pad from the footrest B.
• Lift to remove the pad C.
• To replace the pad, refer to Assembly steps 7 - 9.
• The pad and body support are machine washable. Wash them
separately in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly.
• The frame, toy bar and toys may be wiped clean using a mild
cleaning solution and damp cloth. Do not immerse the toy bar.
Do not use bleach. Do not use harsh or abrasive cleaners.
Rinse clean with water to remove residue.