Fisher-Price L5188 User manual

www.fisher-price.co.uk
L5188
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
WARNING

2
• Please read these instructions before use of this product.
• Adult assembly is required.Tool needed for assembly: Phillips
Screwdriver (not included).
• Requires three “C” (LR14) alkaline batteries (not included)
for operation.
• Product features and decoration may vary from photos.
• Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303.www.service.mattel.com.
• Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond,Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
• New Zealand: 16-18 William Pickering Drive,
Albany 1331,Auckland.
•Asia: Mattel East Asia Ltd, Room 1106, South Tower,World Finance
Centre,Harbour City,Tsimshatsui, HK, China.
• Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ.Tel: [phone],
Fax: [phone].
Consumer Information
WARNING
CAUTION
This package contains small parts
in its unassembled state. Adult
assembly is required.
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this reclined cradle on an elevated
surface, since child's movement may
cause bouncer to slide or tip over.
Use only on a floor.
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion),
since seat can tip over and cause
suffocation in soft surfaces.
• Always use the restraint system.
• Never leave the child unattended.
• Never use as a car seat.
• Never use the toy bar as a handle.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. PRINTED IN CHINA
©2006 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. L5188pr-0726

3
Parts
IMPORTANT! Please remove all parts from the package
and identify them before assembly. Some parts may be
packed inside the pad.
4 mm x 30 mm Screw – 2
4 mm x 20 mm Screw – 2
Shown Actual Size
Assembly
• Insert the ends of the front base into the handle holes on the
seat back tube.
Hint: If you cannot insert the front base into the seat
back tube, turn the seat back tube over and try again!
• Insert two 4 mm x 20 mm screws through the hole in the
handles and the ends of the front base.Tighten the screws.
Hint: If the screw does not easily insert through the hole
in the handle and front base, you may not have pushed the front
base completely into the handle. Push the front base into the
handle to align the holes and then insert the screw.
Turn Tube Ends Up
• Place the seat back tube face down, as shown.
• Turn the ends of the tube upright.
Seat Back Tube Handles
Seat Back Tube
Front Base
IMPORTANT! Before assembly, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact
Mattel for replacement parts and instructions if needed.
Never substitute parts.
1
2
Infant Support
Bunny
Seat Pad
Seat Back Tube
Soothing Unit
Base Tube
Front Base
Toy Bar

4
Assembly
Handle Tubes
Back Base
• While pressing the buttons on the ends of the back base, insert
the ends into the tube ends in the handle. Make sure the back
base “snaps” into place.
• Pull the back base to be sure it is secure to the handle tubes.
• Turn the assembly upright.
• Position the soothing unit upright and fit the groove to the
front base, as shown.
• Insert two 4 mm x 30 mm screws through the front base and
into the soothing unit.Tighten the screws.
Soothing Unit Groove
Front Base
3
4
Front Base Lower Pocket
• Fit the pad lower pocket around the front base and soothing unit.
• Turn the assembly face down.
• Fasten both pad side flaps to the strap on the back of the pad.
Make sure you hear a “snap” on both sides.
Seat Back Tube
Upper Flap
• Fit the upper flap on the pad around the seat back tube.
5
6
PRESS
PRESS

5
• Fit the toy bar into the socket in the handle .Turn the toy
bar to secure in place .
5
Assembly
7
• Place the infant support on top of the pad.
• Insert the restraint pad through the slot in infant the support.
Make sure the restraint pad is not twisted.
• Thread the restraint straps through the slots in the infant support.
• Attach the bunny to any of the fastener tabs on the sides of the
pad or toy bar, as shown.
Assembly is now complete.
8
Infant Support
Toy Bar
Socket



6
Battery Compartment
1,5V x 3
“C” (LR14)
Front Tube
• Remove the pad lower pocket from the front tube.
• Loosen the screw in the battery compartment door and
remove the battery compartment door.
• Insert three “C” (LR14) alkaline batteries into the
battery compartment.
• Replace the battery compartment door and tighten the screw.
• Fit the pad lower pocket around the front base and
soothing unit.
1
Hint: We recommend using alkaline batteries for
longer battery life.
2
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product.
To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use.Always
remove exhausted batteries from the product. Dispose
of batteries safely. Do not dispose of product in a fire.
The batteries inside may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only
to be charged under adult supervision.
Battery Installation Battery Safety Information

7
Setup and Use
WARNING
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this reclined cradle on an elevated
surface, since child's movement may
cause bouncer to slide or tip over.
Use only on a floor.
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion),
since seat can tip over and cause
suffocation in soft surfaces.
• Always use the restraint system.
• Never leave the child unattended.
• Never use as a car seat.
• Never use the toy bar as a handle.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
Restraint Pad
Restraint Strap
Free End
To tighten the restraint straps:
• Feed the anchored end of the restraint strap up through the
buckle to form a loop . Pull the free end of the restraint strap .
To loosen the restraint straps:
• Feed the free end of the restraint strap up through the buckle
to form a loop . Enlarge the loop by pulling on the end
of the loop toward the buckle. Pull the anchored end of the
restraint strap to shorten the free end of the restraint strap .
Securing your Infant
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten the restraint straps to the restraint pad. Make sure you
hear a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child.The restraint system should
remain attached.
Anchored End
TIGHTEN
1
2
Anchored End
Free End
LOOSEN

8
• Make sure your child is properly secured in the seat.
• Slide the power switch to for music; to for vibrations; to
music and vibrations; to off to turn vibrations and music off.
Hint: Vibrations/Music turn off after approximately 15 minutes.
To turn vibrations/music back on, slide the power switch off
and then to the desired on mode.
IMPORTANT! Low battery power causes this product to operate
erratically: no vibrations/music and the product may not turn off.
Remove and discard all three batteries and replace with three,
new “C” alkaline batteries.
Soothing Unit
Button
Back Tube
• The pad, bunny and infant support are machine washable.
Wash them separately in cold water on the gentle cycle.
Do not use bleach.
Tumble dry separately on low heat and remove promptly.
• The frame and toy bar may be wiped clean using a mild
cleaning solution and a damp cloth. Do not use bleach. Do
not use harsh or abrasive cleaners. Rinse clean with water to
remove residue.


• Turn the seat upright.
• First remove the bottom pocket of the pad . Then, remove
the upper pad flap .
To replace the pad, refer to Assembly steps 5 - 6.
To remove the pad:
• Place the seat face down on a flat surface.
• Unfasten the side buckles.
1
2
Care
• While pressing the buttons on the handles, push the back tube
towards the front tube.
Hint: To set-up this seat again, simply pull the back tube back
until it “snaps” into place.