Fisher-Price Sparkling Symphony 79635 User manual

w
w
w.
fi
s
he
r
-p
r
i
c
e
.
c
o
m
Bouncer
Sparkling Symphony™
Model Number: 79635
Please keep this instruction sheet for future reference,
as it contains important information.
Read all instructions before use of the infant bouncer seat.
Adult assembly is required.Tool required for assembly:
Phillips Screwdriver (not included).
Requires three “C” (LR14) alkaline batteries (not included).
79635a-0920.qrk 10/26/01 12:06 AM Page 1

2
Warnings
IMPORTANT!
To prevent serious injury and/or falls:
•Never use on any elevated surface,
since child’s movement may cause
bouncer to slide or tip over.
•Never use as a carrier or lift while child
is seated.
•Always use the restraint system.
•Never leave child unattended.
•Never use as a car seat.
•Never use with a child able to sit
up unassisted.
WARNING
Do not use this infant bouncer seat if it is damaged or broken.
79635a-0920.qrk 10/26/01 12:06 AM Page 2

Parts
3
3/4
" Screw - 3
Pad
Footrest
Mobile Base
Soothing Unit
Mobile Arm
Mobile
Connector
Seat Back
Tube
Right Base Wire
Left Base Wire
Base Tube
Both Shown Actual Size
Lock Nut - 3
79635a-0920.qrk 10/26/01 12:06 AM Page 3

Battery Installation
4
1.5V x 3
“C” (LR14)
SHOWN ACTUAL SIZE
+
–
Battery Compartment Door
Battery Tips
•Do not mix old and new batteries.
•Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
•Remove the batteries during long periods of non-use. Always remove the
exhausted batteries from the product. Battery leakage and corrosion can
damage the product. Dispose of the batteries safely.
•Do not dispose of batteries in a fire. Batteries may explode or leak.
•Never short circuit the battery terminals.
•Non-rechargeable batteries are not to be recharged.
•Only batteries of the same or equivalent type as recommended in the
“Battery Installation” instructions are to be used.
•If removable rechargeable batteries are used, they are only to be charged
under adult supervision.
•Rechargeable batteries are to be removed from the product before they
are charged.
•If you use a battery charger, it should be examined regularly for damage to
the cord, plug, enclosure and other parts. Do not use a damaged battery
charger until it has been properly repaired.
•Loosen the screw in the soothing unit battery compartment door with
a Phillips screwdriver. Remove the battery compartment door.
•Insert three "C" (LR14) alkaline batteries, as indicated inside the
battery compartment.
•Replace the battery compartment door. Tighten the screw with a Phillips
screwdriver. Do not over-tighten.
Hint: We recommend the use of alkaline batteries for longest battery life.
79635a-0920.qrk 10/26/01 12:06 AM Page 4

•Place the base tube on a flat surface as shown.
•Position the left and right base wires as shown. Note the location
of the colored tabs on the left and right base wires.
•Fit the left base wire into the base tube.
•Fit the right base wire into the base tube.
Assembly
Base Tube
Left Base
Wire
Colored Tabs
Right Base
Wire
1
•Loosen the screw in the soothing unit clip with a Phillips screwdriver.
•Slide the soothing unit onto the footrest, as shown. Make sure the
footrest is completely in the grooves around the sides and back
end of the soothing unit.
•Tighten the screw in the soothing unit clip with a Phillips screwdriver.
Do not over-tighten.
Soothing Unit
Clip Screw
Footrest
Soothing Unit
2
5
This package contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
79635a-0920.qrk 10/26/01 12:06 AM Page 5

•Position the mobile base so that the opening is upright.
•Slide the mobile base onto the right base wire.
Assembly
Tabs
Flex Base
Wires Inward
3
6
Base Tube
Colored Tab
Back View
Base Wire
Footrest with
Soothing Unit
Right Base Wire
Mobile Base
Opening
4
•Position the footrest so that the soothing unit is upright.
•While flexing the base wires toward each other, hook the footrest
onto the ends of the base wires.
•Push the footrest down completely to the tabs on the base wires.
•Make sure the colored tabs on the left and right base wires are visible
through the base tube holes (see inset). If the colored tabs are not
visible through the base tube holes, you have assembled the base
incorrectly. Disassemble all parts and refer back to Assembly Step 1.
79635a-0920.qrk 10/26/01 12:06 AM Page 6

•Fit the seat back tube completely onto the
base wires.
•Align the screw holes in the mobile base, seat back tube and
base wire.
•Fit a lock nut (rounded side outward) into the hexagonal openings on the
inside of the mobile base.
•Insert two screws into the holes in the outside of the mobile base.
•Tighten the screws with a Phillips screwdriver. Do not over-tighten.
Assembly
5
7
Seat Back Tube
Mobile
Base
Base Wires
Lock Nut
Rounded Side
Hint: You will need to fit the seat back tube into the mobile base on one side of
the assembly.
79635a-0920.qrk 10/26/01 12:06 AM Page 7

•Fit the connector onto the seat back tube,
as shown.
•Align the holes in the connector, seat back tube and left base wire.
•Fit a lock nut (rounded side outward) into the hexagonal opening on
the inside of the connector.
•Insert a screw through the hole in the outside of the connector.
•Tighten the screw with a Phillips screwdriver. Do not over-tighten.
Assembly
6
8
Seat Back Tube
Connector
Left Base Wire
7
Pull Up
•Pull up on the seat back tube to be sure it is secure. If you can
remove either end of the seat back tube, you have not assembled
it correctly. Remove the screws and lock nut. Re-read and repeat
Assembly steps 5 – 7.
Lock Nut
Rounded Side
79635a-0920.qrk 10/26/01 12:07 AM Page 8

•Unbuckle the restraint belts from the
buckle pad. Push the restraint belts
through the slots in the pad .
•Fit the pad upper pocket onto the
seat back tube .
•Lift the footrest. Fit the pad lower pocket onto the footrest .
Lower the footrest.
B
•Fit both restraint belts back through the pad slots, as shown.
Assembly
Seat Back
Tube
Footrest
8
9
9
Restraint Belts
B
79635a-0920.qrk 10/26/01 12:07 AM Page 9

•Tuck the pad flap loop underneath and around the mobile base.
•Hook the pad flap loop to the peg on the underside of the mobile
base.
Assembly
10
10
Pad Flap
Pad Flap
Loop
Mobile Base
Mobile Base
Peg
Pad Flap Loop
Back View
79635a-0920.qrk 10/26/01 12:07 AM Page 10