Fisher-Price Sounds 'n Lights Deluxe Soothing Bouncer User manual

SOUNDS 'N LIGHTS DELUXE
SOOTHING BOUNCER
Model Number: 79024, 79439, 79613
Please save these instructions for future reference.
Tool needed for adult assembly: Phillips screwdriver (not included).
Requires one “D” (LR20) alkaline battery (not included) in the soothing unit.
Requires three “AA” (LR6) alkaline batteries (not included) in the toy bar.
Slide switch to
or AND bat
irror for sounds
and lights!

2
Occasionally a consumer may experience
a problem with one of our products.
If this should happen, please call us toll-free,
rather than return this product to the store.
Usually, we can solve the problem over the telephone
or send you replacement parts.
Please call Fisher-Price®Consumer Relations,
toll-free at 1-800-432-KIDS,
between 8 AM - 6 PM EST, Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment,
please call 1-800-382-7470.
Or write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
CONSUMER INFORMATION
WARNINGS
To prevent serious injury and/or falls:
• Never use on any elevated surface.
• Never use as a carrier or lift while
child is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Never use with a child able to sit
up unassisted.
WARNING

3
PARTS
#8 - 32 x 1/2" Screw - 2
Shown Actual Size
2 Flowers
Butterfly
2 Paddles
Toy Bar
Pad
Footrest with
Soothing Unit
Seatback
Tube
Right Base
Tube
Left Base
Tube
Base
Connector
#8 - 32 Nut - 2
Shown Actual Size

4
BATTERY INSTALLATION
Soothing Unit
• Locate the soothing unit on the footrest.
• Insert a coin into the battery compartment door and pry the battery
compartment door off.
• Insert one “D” (LR20) alkaline battery, as indicated inside the battery compartment.
Be sure to place the battery on top of the ribbon.
Hint: We recommend the use of an alkaline battery for longest battery life.
• Replace the battery compartment door and be sure it snaps securely closed.
Hint: For easy battery removal, simply lift the ribbon.
Battery Compartment
Door
1.5V
“D” (LR20)
SHOWN ACTUAL SIZE
+–

BATTERY INSTALLATION
Toy Bar
• Locate the battery compartment door on the back side of the toy bar.
• Loosen the screw in the battery compartment door with a Phillips screwdriver
and lift to remove the door.
• Insert three "AA" (LR6) alkaline batteries, as indicated inside the battery
compartment. Be sure to place the batteries on top of the ribbon.
Hint: We recommend the use of alkaline batteries for longest battery life.
• Replace the battery compartment door and tighten the screw with a
Phillips screwdriver. Do not over-tighten.
Hint: For easy battery removal, simply lift the ribbon.
Battery Tips
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use. Always remove the
exhausted batteries from the product. Battery leakage and corrosion can
damage the product. Dispose of the batteries safely.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the
“Battery Installation” instructions are to be used.
• If removable rechargeable batteries are used, they are only to be charged
under adult supervision.
• Rechargeable batteries are to be removed from the product before they
are charged.
• If you use a battery charger, it should be examined regularly for damage
to the cord, plug, enclosure and other parts. Do not use a damaged
battery charger until it has been properly repaired.
SHOWN ACTUAL SIZE
1.5V x 3
“AA” (LR6) +
–
5

6
ASSEMBLY
• Place the base connector on a flat surface as shown.
• Position the left and right base tubes as shown. Note the locations
of the colored dots on the left and right base tube.
• Fit the left base tube into the base connector.
• Fit the right base tube into the base connector.
• Make sure both colored dots on the base tubes are covered by the
base connector.
1
Base
Connector
Colored
Dots
Right Base
Tube
Left Base
Tube
This package contains small parts in
its unassembled state.
Adult assembly is required.
CAUTION

3
7
• Position the footrest so that the soothing
unit is upright.
• While flexing the base tubes toward each
other, hook the footrest onto the ends of the base tubes.
• Push the footrest down completely, below the colored dots on the
base tubes.
• Make sure the small tabs on the left and right base tubes are secure in
the base connector holes (see inset). If the small tabs are not secure in
the base connector holes, you have assembled the base incorrectly.
Disassemble all parts and refer back to Assembly Step 1.
ASSEMBLY
2
Base Tube
Colored Dot
Base Tube
Soothing
Unit
Footrest
Colored
Dot
• Position the seat back tube with the toy bar sockets upright.
• Fit the seat back tube completely onto the base tubes, so that each end
covers the colored dot on each base tube.
•Make sure the plastic covers on the seat back tube cover the colored
dots on the base tube.
Colored
Dot Plastic
Cover
Base
Tube
Toy Bar
Socket
Seat Back
Tube
Back View
Base
Connector
Base
Tube

8
ASSEMBLY
• Insert a screw through the outside of each plastic cover and tighten
with a Phillips screwdriver. Do not over-tighten.
• Pull up on the seat back tube to be sure it is secure. If you can remove
either end of the seat back tube, you have not assembled it correctly.
Remove the screws, re-read and repeat Assembly steps 3 and 4.
4
#8 x 32 Nut
Pull Up
Protruding Side
Plastic
Cover
• Fit the nut (so that the protruding side is
facing the seating area) into the hexagonal
opening on the inside of each plastic cover.

9
ASSEMBLY
5
Seat Back
Tube
Slot
Pad
Restraint
Belt
A
C
B
• Position the pad with the ruffle upright.
• Fit the upper pocket on the back
of the pad onto the seat back tube .
• Lift the footrest. Fit the lower pocket on
the back of the pad onto the footrest .
Lower the footrest.
• Fit the restraint belts through the slots in the pad .
C
B
A
C

10
ASSEMBLY
• Wrap the elastic straps on the pad
flaps around the outside of each
plastic cover.
• Hook the elastic straps to the peg on
the inside of each plastic cover.
6
Elastic
Strap
Elastic
Strap
Inside View
Elastic
Strap
Plastic
Cover
Plastic
Cover
Plastic
Cover
Peg