Fisher-Price Jeep Push'n Scoot 72607 User manual

Jeep
Push’n Scoot™
Model Number: 72607
Front Axle Replacement Kit
• Adult assembly is required.
• Tools needed: Pliers, hammer, scrap block of wood
• Follow these instructions to replace the front axles on your vehicle.
Please replace both front axles at the same time, even if only
one of the front axles shows wear or damage.
• If you have any questions or are missing a part, please call
Mattel Australia’s Consumer Advisory Service at 1-800-800-812
(valid in Australia only).
®
’

Removing the Front Axles
2
Replacement Parts
“A” Front Axle “B” Front Axle 5 Cap Nuts*
• Remove the two cap nuts from each front axle assembly. Use pliers to firmly
squeeze the rim on a cap nut. Release, and reposition the pliers to squeeze
the cap nut in the opposite direction. Repeat this cycle until the cap nut
loosens and can be pulled off the front axle.
“A” “B”
*One extra cap nut has been included for your convenience.

• Remove the front axle assemblies from the vehicle body. Discard the front
axles and cap nuts only. Save all bushings, washers and the front wheels
for re-assembly.
Cap Nut Cap Nut
Front Axles
Front Wheel Front Wheel
Bushing
Bushing
Bushing
Bushing
Washer
Washer Washer
Washer
Removing the Front Axles
3
Save These Parts
4 Bushings 4 Washers 2 Front Wheels

• Identify and separate the "A" and "B" front axles.
• Place the "A" front axle on a scrap block of wood.
• Slide a washer onto the "A" front axle.
• Slide one of the wheels, spoke side up, onto the "A" front axle.
• Fit a cap nut onto the axle and tap the cap nut with a hammer. Make sure
the cap nut is secure on the axle.
A
Cap Nut
Wheel
Washer
Spoke Side Up
Scrap Block
of Wood
"A" Front
Axle
B
"A" Front
Axle
"B" Front
Axle
A
• Slide a washer onto the "A" front axle.
• Slide a bushing, narrow side up, onto the "A" front axle.
• Repeat steps 1and 2 to assemble the "B" front axle, washer, wheel, bush-
ing and cap nut.
Bushing
"A" Front Axle
Washer
2
2
1
1
4

Front Axle Assembly
• Lift the front end of the vehicle body and locate the side of the vehicle body
marked "A".
IMPORTANT! For proper wheel position, the "A" front axle assembly must be
inserted into the hole in the vehicle body marked "A".
• Insert the "A" front axle up into the hole underneath the vehicle body
marked "A".
• Make sure the bushing fits into the hole in the vehicle body.
Bushing
"A" Front Axle
"A" Marking Vehicle Body
3
3
5

Fisher-Price, Inc., a subsidiary of Mattel, Inc.,
East Aurora, New York 14052, U.S.A.
©2000 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc. Printed in U.S.A.
Thank you for choosing Fisher-Price®. If you have any questions, please call
Mattel Australia’s Consumer Advisory Service at 1-800-800-812 (valid in
Australia only) or, write to:
Mattel Australia Pty. Ltd.
658 Church Street
Locked Bag #870
Richmond, Victoria 3121
• Lower the vehicle body.
• Fit a bushing, narrow side down, onto the exposed end of the "A" front axle
and into the hole in the vehicle body.
• Fit a cap nut onto the end of the "A" front axle.
• Tap the cap nut with a hammer. Make sure the cap nut is secure.
• Repeat assembly steps 3and 4to assemble the "B" front axle to the side of
the vehicle body marked "B".
Front axle replacement is complete.
Cap Nut
"A" Front Axle
Bushing
Vehicle Body
4
4
6