Fisher 29801 User manual

1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning disassembly process.
SAFETY
Dimensions
A 14 3/8”
B 14”
C 9 3/4”
D 2 1/2”
E 6 1/8”
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding. Turn over the page for more detailed instructions and drawing configuration.
This reel is configured to be wall mounted. The hose reel is equipped with a universal mounting bracket so that it can
be mounted on the floor, wall or ceiling. In order to modify it’s factory set position the hose guide arm can be moved
to the position desired by removing the screws fastening the guide bracket to the reel base. Shift the guide arm bracket
so the hose comes off the reel at the desired position and replace the screws. NOTE: For proper installation in wall mount
applications, ensure reel is mounted with inlet on the right as you are facing the reel. Failing to do so could cause latching issues.
Hose reel spring and bearings are factory lubricated and require no further lubrication.
LUBRICATION:
REPLACING HOSE:
1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
MOUNTING:
Operating Instructions
Model:29801
Spring Driven Reel
Fisher Manufacturing Co. • 1900 “O” Street, Tulare, CA 93274
Ph: 800-421-6162 / 559-685-5200 • Fax: [phone]
Part No.75004 Rev.A

Model: 29801 Spring Driven Hose Reel
Model: 74988 Reel Kit Pro Spray Valve
Page 2
Item # Description # Req. 29801
2980-R027
75079
9 Bumper Stop Assembly 1
10 Hose Assembly 1
14 Drive Spring 1
31 Swivel Assembly 1
32 Swivel Union 1
Hose I.D. and Length 3/8” x 30 FT
Reel Inlet Connection 3/8” F.P.T.
Max. Operating Pressure 200 P.S.I.
Max. Operating Temperature 160 °F
Item # # Req. Description
Item # Req.# Part Description
Item # # Req. Description Item # # Req. Description
12
1” Snap
31 1
75066 Hose RR 3/8m x 1/2f x 1 1/2 ft
32 12980-R020 Tube vinyl clear 6 inch
33 12913-3/8 Handle 3/4-14f X 3/8f
34 12922-5000 Gasket Handle
35 12990 Pro Spray Valve
36 13298 PST Thread Sealant
Ring 11 1 Guide Arm Assembly 21 1 Latch Bushing
22
Spacing Washer 12 1 Base Assembly 22 1 Latch Spring
33
1/4-10 x 5/8”
Self Tapping Screw 15 1 Spring Case Stud 24 1 O-ring
41
Sheave Flange 16 1 3/8-16 x 1/2” Set Screw 25 1 Latch Plate Assembly
51
Sheave Disk 17 1 Spring Case & Hub Assembly 26 1 10-32 x 1” Machine Screw
61
Latch Cam 18 8 10-32 x 3/8” Nyloc Nut 27 1 U-bolt Hose Clamp
72
Spring Arbor 19 1 Latch Plate Bumper 28 2 1/4-20 Nyloc Nut
87
10-32 x 1/2” Machine Screw 20 1 10-24 x 3/8”Self Tapping Screw 30 1 Main Shaft
31
32
33
34
35
36
1. Connect the lead-in line (31) to the reel (29801) inlet located on the right-hand side of the hose reel,
by appling PST (36) or plumbers tape on the male 3/8” NPT threads on the lead-in line (31) and thead it
to the reel (29801) using a wrench to support the swivel while tightening the lead-in line.
2. Connect the 1/2” female end of the lead-in line (31) to the water supply using PST (36) or plumbers tape
and tighent.
3. Turn on water supply and flush the reel line to remove any debis from the reel for a few seconds and
then turn off water supply.
4. Slide the clear vinyl tube (32) over the reel hose up to the bumper (9).
5. Attach the handle (33) to the reel hose (10). By appling PST (36) or plumbers tape on the 3/8” NPT male threads on reel hose
and tighen.
6. Insert the gasket handle (34) into the handle (33) and then connect the pro spray valve (35).
7. Turn water supply on and check for leaks.
NOTE: Apply PST or Plumber Tape on
the following locations to prevent any
leaks.
1
1
1